Crosswater 11-04 Bedienungsanleitung

15122805

Berea Floor-mount Tub Filler

11-04

Installation Instructions

Before beginning installation, check for any damage

that may have occurred during transport.

Note: Damage claims cannot be made during or

after installation.

For ease of installation you will need:

To read the installation instructions completely before beginning.

To read all warnings, care, and maintenance information.

Anti-scald protection is the responsibility of the installer and

according to applicable codes.

11-04

Installation Instructions

15122805 2

3 4 5

Adequate floor support is required. The WOOD SUPPORT must be a minimum of

2" (51mm) thick by 10" (254mm) wide. Wood support must be located within

the MIN. and MAX. arrows that are marked on the plaster guard.

Use 4 screws to install and fix the mounting base to the wood support board.

Use level from bottom on both directions to make sure wood support board is flat.

Secure wood support to floor joists.

Assure the valves are centered in

holes that are 3-1/4" to 3-5/8" diameter.

This is required to allow mounting base

to be installed properly.

Turn water supply off. Remove the

plaster guards and the test plugs with

the supplied hex wrench.

Thread and securely tighten 1/2" male

NPT hot and cold supply lines into the

mounting base. Make sure the hot line

is installed on the left side of the

mounting base when facing the

mounting base from the front of where

the floor tub filler will fill the bathtub.

Slide escutcheons onto riser pipe.

Thread hot and cold riser pipes into the

appropriate side of the mounting base

making sure the hot riser is attached to

the hot water supply as noted in the

image above.

FINISHED FLOOR

MIN 2"

MAX 3 1/8"

10"-12"

MIN 10"

FLOOR JOIST

MIN 2"

WOOD SUPPORT

FINISHED FLOOR LINE

en -

vel

uslot

Hot

Cold

1/2-14 NPT

Mounting base

Hot

Cold

FINISHED FLOOR

3 3/8＂- 3 9/16

FOR HOT SIDE ONLY

5mm HEX WRENCH

Mount valve body on the riser pipe

assembly. Assure the washers are in

place.

Attach hose to spout and handheld

shower. Turn on the water supply to

test the hot, cold and diverter water

flow.

Installation is complete.

Attach handshower yoke to valve

body. Assure the washer is in place.

7 86

9 10 11

Replacement Parts

151228053

Before final installation, check that all

sealing surfaces are clean.Install the

mounting adapters onto the mounting

base. Install the mounting screws and

washers through the mounting plate.

And into the mounting base. Do not

tighten. Rotate the tub filler right or left

to align with tub. Tighten mounting

screws to secure tub filler.

Hot

FOR HOT SIDE ONLY

FINISHED FLOOR

FOR HOT SIDE ONLY

To adjust the handshower yoke to

reverse direction, unscrew the nut and

rotate the yoke by 180 degree and

then tighten the nut.

5mm HEX WRENCH

11-04

Installation Instructions

15122805 4

NO. Description Part No.

Handshower

5F0M0159010A0

Cartridge - Hot

52009335NT

Cartridge - Cold

52009347NT

Diverter Handle

Handle Assembly- Hot

9Q240700

9Q240500

Handle Assembly- Cold 9Q240600

5Y00103000

9Q241000NT

9Q241200NT

9Q241100NT

Hex screw and Key

5P00031000

Riser Pipe Assembly- Cold

5y00102000

9Q240800NT

Diverter cartridge

9Q240900

Riser Pipe Assembly- Hot

Handshower Yoke

Mounting Base

Escutcheon

5T0F0143NT

Cold Riser Washer

Washer

5R9R0042PL

Aerator Assembly 5Q0M0443PL

5N0C0583NT

Mounting Plate

Mounting plate

Mounting Base

5R4R0128PL

9Q241300NTDiverter Washer Assembly

Handshower Hose

9Q242500

5T4F0006ZZ

5mm HEX WRENCH

2.5mm HEX WRENCH

11-04

Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean, soft

cloth after each use. Rinse completely with water and dry any

overspray. This will maintain the finish and avoid water spotting.

To remove mineral deposits, use a 50/50 solution of white vinegar

and water. Do not allow the solution to soak on the product.

Simichrome Polish® contains a protective film to enhance

maintenance and is helpful in preventing water spot buildup.

Follow instructions to ensure optimum results.

Never use an abrasive material such as a brush or scouring pad to

clean the surface. The use of abrasive cleaners, cleansers or

disinfectants will alter the surface finish and void the warranty.

Do not allow certain materials such as toothpaste, cologne, shaving

cream, nail polish remover, vinegar, wine, drain and glass cleaners

to remain on the surface. Prolonged contact will alter surface

finishes and void the warranty.

We DO NOT recommend using any household cleaners as

many can cause damage to the finish.

Please see the website for care instructions for specific finishes.

Installation Dimensions

IAPMO certified to meet or exceed the following:







11-1/2"

8-1/2"

7/8



34-5/8 - 35-3/4"

43-1/4" - 44-1/2"

2 - 3-1/8

31" - 32-1/4"

5-7/8

7-7/8

9 "

2-1/2-14NPT

5-7/8

1-1/4"

1-1/8

3-1/8

3/4"

Finished Floor

Replacement Parts

15122805

11-04

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.

For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757

Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-0433 fax: 508-381-6068

www.crosswaterlondon.com

email: technical@crosswaterlondon.com

Issue date: 20102020

Inhaltsverzeichnis

Andere Crosswater Sanitärprodukte Handbücher

Crosswater

Crosswater KL322DC Bedienungsanleitung

Crosswater

Crosswater US-SP380 Bedienungsanleitung

Crosswater

Crosswater US-BSW0101 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF422175 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC15 Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL130 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF0613 Bedienungsanleitung

Crosswater

Crosswater Berea 11-19-T Bedienungsanleitung

Crosswater

Crosswater Solo Produkthandbuch

Crosswater

Crosswater UNION US-UN800 Bedienungsanleitung

Crosswater

Crosswater Wisp US-WP418 Bedienungsanleitung

Crosswater

Crosswater Berea 11-02-T Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC14 Bedienungsanleitung

Crosswater

Crosswater INFINITY 500mm FURNITURE Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-20-T Bedienungsanleitung

Crosswater

Crosswater SIMPONS CLIC DOUBLE PANE BATH SCREEN... Bedienungsanleitung

Crosswater

Crosswater Leyden 14-05 Bedienungsanleitung

Crosswater

Crosswater UNION US-UN399 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC600 Bedienungsanleitung

Crosswater

Crosswater US-ARC953 Bedienungsanleitung

Crosswater

Crosswater PRO125DNJ Bedienungsanleitung

Crosswater

Crosswater Belgravia Wall Union US-BL004 Bedienungsanleitung

Crosswater

Crosswater Darby 15-16-T Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-15P-T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema