Crosswater PRO125DNJ Bedienungsanleitung

BASIN 2 HOLE SET NO WASTE DECK MOUNTED PRO125DNJ/C/V

INSTALLATION INSTRUCTIONS

For any further information please contact

Crosswater on: 0845 873 8840

Or visit our web-site at www.crosswater.co.uk

The manufacturer reserves the right to make technical

modifications without prior notice.

P5-208560F8-PR-E A/0

This product should only be fitted by a qualified plumber to NVQ (National Vocational

Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3. Should

the installation be completed by a non-qualified person then the guarantee may be

considered invalid.

For a claim made under our warranty written certification of your installers credentials

can be required. For further information or to find a qualified installer in your area

please visit the Institute of Plumbers website - www.iphe.org.uk

At present, to be a plumber you need to follow the National Vocational Qualification

(NVQ) route (Scottish National Vocational Qualification - SNVQ - in Scotland). These

qualifications are made up of theory and practical work in the classroom/purpose built

training facility and work based experience with a working plumber. Colleges should

help students find a work placement, although many students organise it themselves.

The S/NVQ qualification works in levels. All recently qualified plumbers should hold

S/NVQ Level 2 as basic with Level 3 as the preferred level. Level 2 will give you the

foundation you need for a career in plumbing and teach you domestic plumbing to a

satisfactory level. Level 3 is more comprehensive and deals with domestic,

commercial and industrial plumbing along with aspects such as gas - if you want to one

day set up your own business, this is the level to reach. The Institute of Plumbing and

Heating Engineering, and the industry as a whole recommends that all plumbers reach

a minimum of Level 3.

Reaching Level 3 has other advantages. The Institute runs a Master Plumber

Certificate, which only those attaining Level 3 or equivalent can reach as long as they

have the relevant experience as well. Those with S/NVQ Level 3 can (once in

membership with the Institute for five years as a Member MIPHE) gain Engineering

Technician EngTech status with the Engineering Council (UK).

THE QUALIFICATIONS

DIMENSIONS

NOTE: ALL DIMENSIONS IN MILLIMETRES

INTRODUCTION

Please read these instructions carefully and keep in a safe place for future reference.

General Installation Requirements.

The installation must comply with regulations of the Local Water Authority as contained in

their bylaws. All of the taps in this range are single flow (the hot and cold water mix in the

body) and should therefore be supplied with hot and cold water at balanced pressures,

both from the tank or both from the mains (via a combination boiler for example). If the taps

are not supplied at balanced pressures then the mixer will not function correctly. It will also

be necessary to fit non-return valves on both hot and cold feeds.It is very important that all

pipework is flushed thoroughly after installation to avoid damaging the ceramic discs.

Minimum/Maximum working pressure HP1

These taps are suitable for high These taps are suitable for high pressure installations

They are fitted with a half turn ceramic disc cartridge which provides a good flow rate with

very smooth movement. The maximum water pressure is 6 bar (note: mains cold water is

normally supplied at between 2 and 3bar). For installations where the mains pressure

exceeds 6 bar a pressure reducing valve should be fitted.

The tap is fitted with an aerator for use in high pressure installations. If your water is

supplied at low pressure you may prefer to change the nozzle to a flow straightener.

Approvals

All products are manufactured using materials tested and approved under the Water Bylaws

Scheme and comply with requirements of British Standard 5412:1996 where applicable.

Preparation and byelaw requirements

These taps are single flow so the hot and cold water mix in the body. Water byelaws require

that where the hot water is supplied from a tank and cold from the mains, non return valves

are fitted on both hot and cold pipes as close as possible to the tap. These are not supplied.

Where combination boilers are fitted it is only necessary to shut off the incoming mains and

turn the boiler off and non return valves are not required.

WARNING

Before installing the new mixer it is essential that you thoroughly flush through the

supply pipes in order to remove any remaining swarf, solder or other impurities.

Failure to carry out this simple procedure could cause problems or damage to the

working of the mixer.

These hints have been prepared for your guidance, you must exercise due care at all times.

We do not accept responsibility for any problems that may occur through incorrect

installation.

178

PRO125DNJ/C/V

50 50

206

SCREWSCREW

INSTALLATION INSTALLATION

First shut off your water heating system then, with your mains stop cock closed, open the

lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes

are empty (the hot water storage cylinder always remains full).

Fitting isolating valves to the inlet feeds is recommended for ease of maintenance.

The basin spout must be firstly screw the two flexible hoses (as illustrated) into the basin spout

then inserted through the centre tap hole on the basin (or work top) ensuring that there is

enough thread to tighten the spout to the unit .Slide the C- shaped black washer and then the

metal retaining plate up the threaded screw and secure screwing the fixing nut with an

adjustable spanner. Both side bodies must then be fitted (from the under-side of the basin or

work top, without the chrome flanges fitted) making sure that the “back nuts ” are already

screwed onto the threads .The outlets of both side bodies must then be aligned so that the

flexible pipes can supply water to the spout (which have already been secured) .Once this

alignment is achieved the back nuts under the basin can be tightened to allow the chrome

flanges to be fitted from above the controls .The copper pipes then need to be secured using

the compression fittings and washers supplied for the hot and cold supplies.

The Hot (to the left side) and Cold (to the right side) water supplies can then be connected to

the 1/2” fittings at the bottom of each side body.

The tap then must be examined for any leaks under the basin.

INSTALLATION

Remember to turn off the mains water supply before connecting to any existing

pipe work.

ATTENTION

Having first checked all new connections, turn on the mains stop cock, close all taps except the

new mixer and as the system starts to refill check for leaks.

Once you have satisfied yourself that there are no leaks, switch on the water heating.

PRO125DNJ/C/V

THREADED

STUD

WASHER

NOZZLE

HANDLE

NUT

WASHER

NUT

SLEEVE

WASHER

FLEXIBLE

PIPES

SCREW

MAINTENANCE

Once the valve has been set

correctly the collar can be screwed

down to secure the unit. The handle

is then pushed onto the spline and

tightened with the hex key.

CLEANING

The chrome and gold plate we use on our taps is very durable, nevertheless care should

be taken when cleaning them. They should be cleaned only with warm soapy water

followed by rinsing with clean water and drying with a soft cloth. All finishes are vulnerable

to acid attack and some strong substances such as household cleaners, disinfectants,

denture cleaners, hair dyes, wine making and photographic chemicals can cause the

surface to go black or peel.

HEXAGONAL KEY

HANDLE

The hose is connected with the

washer provided. A thread sealant

may also be used such as PTFE tape.

HOT

INLET COLD

INLET

PRO125DNJ/C/V

NUT

WASHER

SCREW

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crosswater Sanitärprodukte Handbücher

Crosswater

Crosswater INFINITY 500mm FURNITURE Bedienungsanleitung

Crosswater

Crosswater Darby 15-15P-T Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-15P-T Bedienungsanleitung

Crosswater

Crosswater 17-20-T Bedienungsanleitung

Crosswater

Crosswater Leyden Robe Hook 14-51 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF422175 Bedienungsanleitung

Crosswater

Crosswater US-ARC953 Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL440 Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL130 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF135 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC600 Bedienungsanleitung

Crosswater

Crosswater Taos Deck-mount Tub Faucet with Handshower Trim... Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF130 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC14 Bedienungsanleitung

Crosswater

Crosswater ATOLL SQUARE EXPOSED THERMO SHOWER VALVE... Bedienungsanleitung

Crosswater

Crosswater 28-07 Bedienungsanleitung

Crosswater

Crosswater Belgravia Wall Union US-BL004 Bedienungsanleitung

Crosswater

Crosswater MPRO US-PRO110 Bedienungsanleitung

Crosswater

Crosswater Berea 11-19-T Bedienungsanleitung

Crosswater

Crosswater Wisp US-WP418 Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-20-T Bedienungsanleitung

Crosswater

Crosswater 28-16-T Bedienungsanleitung

Crosswater

Crosswater US-SP380 Bedienungsanleitung

Crosswater

Crosswater US-BTW0201 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema