Crosswater Wisp US-WP418 Bedienungsanleitung

Installation Instructions

6-3/4"

2-5/8"

11-3/4"

4-7/8" dia.

38-3/4"

33-5/8”

Adjustable

wrench

Channel

locks

Plumbers’ putty

or caulking

Flat head

screwdriver

Cross head

screwdriver

Hexagonal

key

Wisp Thermostatic Floor-mount Tub Filler

US-WP418

Introduction

Installation notes

The faucets in this range are single flow (hot and cold water mix in the

body) and should therefore be supplied with hot and cold water at

balanced pressures. If the faucets are not supplied at balanced

pressures then the mixer will not function correctly.

The minimum water pressure required for these faucets is 20 psi.

The maximum water pressure is 60 psi, (beyond which pressure-

reducing valves must be installed).

The faucets are fitted with quarter-turn ceramic disc cartridges which

provide a good flow rate with very smooth movement.

IMPORTANT: Please read these instructions carefully before

beginning and retain for future reference. These instructions have

been prepared for your guidance, you must exercise due care at all

times.

Before beginning installation, check for any damage that may have

occurred during transport.

Note: Damage claims cannot be made during or after installation.

We do not accept responsibility for any problems that may occur

through incorrect installation.

Dimensions

Tools required

The installation must comply with all plumbing codes including

local

codes and be installed by a licensed plumbing contractor.

US-418ROUGH must be installed first using the instructions

provided with it.

WARNING! Before installing a new faucet it is essential that supply

pipes are thoroughly flushed in order to remove any remaining debris,

solder or other impurities. Failure to carry out this simple procedure

can cause problems or damage to the working of the faucet.

Installing shut-off valves on incoming supply lines is recommended

for ease of maintenance.

Turn off the main water supply before connecting to any existing

pipework or doing any maintenance.

WARNING! Please check for any hidden pipes and cables, electric

or otherwise, before drilling holes in a wall or floor.

PLASTIC

PLATE

SCREWS x4

(Retain for

future use)

VALVE

BODY

COVER

PLATE

VALVE

BODY

UPSTAND

PIPE

34”

LENGTH

SCREWS x4

(Retained)

HANDSHOWER

WASHER

FAUCET

BODY

HOSE

NUT

HOSE

CONE

IMPORTANT:

For valve body installation see installation instructions for

US-418ROUGH before following the trim installation detailed

below.

lWith the main water supply turned o.

lRemove the 4 screws securing the plastic plate.

lRemove the plastic plate with the two plugs.

lKeep the 4 screws in a safe place for future

use.

Installation

lSlide the cover plate up the upstand pipe, taking care not to mark

the surface.

lTurn the body so that the spout is facing the correct direction.

lPush the faucet body down into the valve body.

lThis is a pre-tested product so care should be taken not to put

undue stress on the tails as this could damage the seals within the

body of the faucet.

lFix the faucet body onto the valve body using the 4 screws.

lAt this point the water supply can be switched on and the unit

tested for leaks.

lExtra care and time should be taken to check for leaks as the

valve body will be concealed once installation is complete.

lPosition the cover plate and use a suitable sealant to seal.

lConnect the hose cone, with sealing washer to the handshower.

lConnect the hose nut to the faucet body.

ATTENTION:Check all new connections for leaks.

lOnce satised there are no leaks, switch on the heating system.

Installation

Installation

WASHER

HANDLE

RETAINING

NUT

BRASS

SLEEVE

SCREW

GASKET

SLEEVE

CAP

HEXAGONAL

KEY

DIVERTER

CARTRIDGE

WASHER

HANDLE

RETAINING

NUT

BRASS

SLEEVE

SCREW

LIMIT RING

GASKET

STOP

CAP

HEXAGONAL

KEY

THERMOSTATIC

CARTRIDGE

Cleaning the diverter cartridge

lThe diverter cartridge should give trouble-free service however

servicing is a straightforward process.

To remove the diverter cartridge:

lWith the water supply turned o, carefully remove the cover cap.

lUsing a hexagonal key loosen the set screw but do not remove.

lRemove the handle and gasket.

lUndo the retaining nut and pull the diverter cartridge out with the

sleeve and brass sleeve attached.

lWash the diverter cartridge with clean running water, dry and

lightly grease the seal, (only use silicone grease).

lReplace the diverter cartridge followed by the retaining nut, gasket

and handle.

Thermostatic cartridge

lThe thermostatic cartridge should give trouble-free service,

however servicing is a straightforward process.

To remove the thermostatic cartridge:

lWith the water supply turned o, carefully remove the cover cap.

lUsing a hexagonal key loosen the set screw but do not remove.

lRemove the handle and gasket.

lRemove the temperature limit ring, (take note of the orientation).

lUndo the retaining nut and pull the thermo cartridge out with the

brass sleeve attached.

lWash the thermo cartridge with clean running water and make

sure that any trapped debris has been removed.

lDry and lightly grease the seals, (only use silicone grease), and

replace the thermo cartridge.

lTo re-assemble, reverse the sequence above taking care to replace

the temperature limit ring in the same orientation before removal.

Maintenance

TEMPERATURE

Vertical marking

HANDLE

STOP

RING

STOP

RING

HEXAGONAL

KEY

THERMOSTATIC

CARTRIDGE CAP

Thermo cartridge - Set temperature to the desired maximum

To set the thermo cartridge:

lWith the water supply turned o, carefully remove the cover cap.

lUsing a hexagonal key,loosen the set screw but do not remove.

lRemove the handle and gasket.

lRemove the stop ring, taking note of the orientation of the stop

ring.

lAdjust the temperature of the thermo cartridge to the desired

maximum .

lTo re-assemble, reverse the sequence above taking care to replace

the stop ring in the same orientation as it was before removal.

5 Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any

overspray. This will maintain the finish and avoid water spotting.

To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.

Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow

instructions to ensure optimum results.

Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or

disinfectants will alter the surface finish and void the warranty.

Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass

cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.

We DO NOT recommend using any household cleaners as many can cause damage to the finish.

Please see the website for care instructions for specific finishes.

Warranty: This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.

For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757

Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-0433 fax: 508-381-6068

www.crosswaterlondon.com

email: technical@crosswaterlondon.com

Issue date: 18112019

Inhaltsverzeichnis

Andere Crosswater Sanitärprodukte Handbücher

Crosswater

Crosswater US-BTW0201 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC14 Bedienungsanleitung

Crosswater

Crosswater Darby 15-16-T Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF0613 Bedienungsanleitung

Crosswater

Crosswater 1000 Series Bedienungsanleitung

Crosswater

Crosswater LIBRA LB6117C Series Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL422 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC600 Bedienungsanleitung

Crosswater

Crosswater UNION US-UN800 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF422175 Bedienungsanleitung

Crosswater

Crosswater KWC 10.441.004.000FL Handbuch

Crosswater

Crosswater Leyden Robe Hook 14-51 Bedienungsanleitung

Crosswater

Crosswater WS2001RC Bedienungsanleitung

Crosswater

Crosswater US-ARC953 Bedienungsanleitung

Crosswater

Crosswater Berea 11-01 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC15 Bedienungsanleitung

Crosswater

Crosswater 11-04 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF135 Bedienungsanleitung

Crosswater

Crosswater Berea 11-02-T Bedienungsanleitung

Crosswater

Crosswater PRO125DNJ Bedienungsanleitung

Crosswater

Crosswater 28-07 Bedienungsanleitung

Crosswater

Crosswater US-PRO120 Bedienungsanleitung

Crosswater

Crosswater Leyden 14X-03-T Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-15P-T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema