Crosswater Leyden 14-05 Bedienungsanleitung

15122806

For ease of installation you will need:

To read the installation instructions completely before beginning.

To read all warnings, care, and maintenance information.

Leyden Floor-mount Tub Filler

14-05

Installation Instructions

Before beginning installation, check for any damage that

may have occurred during transport.

Note: Damage claims cannot be made during or after

installation.

Anti-scald protection is the responsibility of the installer

and according to applicable codes.

14-05

Installation Instructions

15122806 2

1 2

FRONT

HOT

COLD

FRONT

SEALING TAPE

Adequate floor support is required. The WOOD SUPPORT

must be a minimum of 2" (51mm) thick by 10" (254mm)

wide. 2x6 lumber is NOT adequate for this application.

WOOD SUPPORT must be located with in the MIN. and

MAX. arrows that are marked on the front of the PLASTER

GUARD .

IMPORTANT: Use a ROUND BUBBLE LEVEL to level the

WOOD SUPPORT . The WOOD SUPPORT must be

perfectly level. Secure WOOD SUPPORT to floor joists.

Check for level again.

Locate the position on the wood support where the

MANIFOLD MOUNTING BASE will be installed. Use the

MANIFOLD MOUNTING BASE as a guide to mark the four

mounting hole locations.Drill pilot holes if required.

Secure the MANIFOLD MOUNTING BASE to the WOOD

SUPPORT with SCREWS provided.Verify that the

MANIFOLD MOUNTING BASE is level and then fully

tighten SCREWS .

Finish all Hot and Cold supply connections to the

MANIFOLD MOUNTING BASE .Loosen the two PLASTER

GUARD SCREWS and remove the PLASTER GUARD.

Make sure the two TEST PLUGS are tight, but do not over

tighten.Turn on water supplies and test for leaks.

Turn off water supplies. Replace PLASTER GUARD and

attach with SCREWS.

Sweat together Hot and Cold Supply assemblies. Apply

sealing tape to threaded connections. With the maximum

and minimum measurement in front, the hot supply is to be

installed on the left inlet and the cold on the right as shown

in the image above.

Note: The inlets are marked hot and cold on the bottom of

the MANIFOLD MOUNTING BASE for reference.

HOT

COLD

FRONT

MIN 2 11/16

MAX 4 13/16

ROUND BUBBLE LEVEL

MIN 2"

10"-12"

FLOOR JOIST

MIN 10"

FINISHED FLOOR LINE

WOOD SUPPORT

HOT

COLD

14-05-PC

14-05-SN

14-05-PN

14-05-BZ

15122806 6 151228063

Applicable Standards/Codes

Installation Dimensions

IAPMO certified to meet or exceed the following:







4 9/16

3 11/16

5 1/16

4 15/16

MAX 4 13/16

1 5/16

2-1/2-14 NPT

MIN 2 11/16

Complete the installation of the Finished Floor. Tile as close

to the PLASTER GUARD as possible.Caulk between

Finished Floor and PLASTER GUARD.

When you are ready to install the TUB FILLER cut the

exposed part of the PLASTER GUARD flush with the

finished floor. Be careful not to damage the floor.

FINISHED FLOOR

8 1/4

11 1/4

10 3/8

8 7/16

1 15/16

38 5/8

35 3/8

30 9/16 32 11/16

24 13/16 26 15/16

32 5/16 34 7/16

1 9/16

5 1/8

4

8 1/8

3 3/8

FINISHED FLOOR

ROUGH FLOOR

Turn off water supplies. With a wrench remove the center

TEST PLUG as shown in Figure A. If the TEST PLUGS

cannot be removed in one piece as shown in Figure A, the

lower half will have to be removed using the supplied 6mm

Hex Wrench as show in Figure B.

Repeat step for the second TEST PLUG.

Remove PLASTIC CAP from bottom of the TUB FILLER.

Before final installation, check that all sealing surfaces are

clean and that the two O-RINGS are installed in the

MOUNTING ADAPTER.Install the MOUNTING ADAPTER

into the MANIFOLD MOUNTING BASE.Install the four

MOUNTING SCREWS and WASHERS through the

MOUNTING PLATE and into the MANIFOLD MOUNTING

BASE. Do not tighten.Rotate the TUB FILLER right or left

to align with Tub.Tighten MOUNTING SCREWS supplied

with 6mm Hex Wrench to secure TUB FILLER.

FIGURE “A” FIGURE “B”

FRONT

6mm HEX WRENCH

FRONT

O-RING SEALS

REMOVE PLASTIC CAP

151228065

14-05-PC

14-05-SN

14-05-PN

14-05-BZ

Replacement Parts

15122806 4

NO. Description Part No.

1 Hand Shower 5F0M0178

Aerator Assembly

5Q0M0025PL

Hand Shower Hose

51014603

3 Diverter Knob Assembly 9Q241700

Hot & Cold Supply 5G0M0237CC

9Q241800

Mounting Assembly 9Q221900NT

5L0P0120Finished Cartridge Dome

9Q241900NT

9Q241500

Hex screw and Key

Cartridge Nut

Mounting Base Screw

5T1A0003AL

Cartridge 5D0M0041PL

Hand Shower Outlet 5Y00111000

Diverter Cartridge 5MD0M0006

5T0F0143NT

Escutcheon

12 Handle Plug & Screw 9Q1229

Handle

Mount handheld bracket onto spout base. Tighten using

supplied hex wrench.

Attach hose to spout and handheld shower.

Once hand shower is attached turn on TUB FILLER and

test the diverter

Turn on water supplies and check all connections for leaks.

Check MANIFOLD connections for leaks.Remove foam

protector and apply sealant to under side edge on

ESCUTCHEON . Slide ESCUTCHEON down to finish floor.

Press into place.Clean up excess sealant.

APPLY SEALANT

FOAM PROTECTOR

Installation is complete.

6mm hex wrench

5T4000400ZZ0

6mm HEX WRENCH

2.5mm HEX WRENCH

13mm HEX WRENCH

2.5mm HEX WRENCH

151228065

Replacement Parts

15122806 4

NO. Description Part No.

1 Hand Shower 5F0M0178

Aerator Assembly

5Q0M0025PL

Hand Shower Hose

51014603

3 Diverter Knob Assembly 9Q241700

Hot & Cold Supply 5G0M0237CC

9Q241800

Mounting Assembly 9Q221900NT

5L0P0120Finished Cartridge Dome

9Q241900NT

9Q241500

Hex screw and Key

Cartridge Nut

Mounting Base Screw

5T1A0003AL

Cartridge 5D0M0041PL

Hand Shower Outlet 5Y00111000

Diverter Cartridge 5MD0M0006

5T0F0143NT

Escutcheon

12 Handle Plug & Screw 9Q1229

Handle

Mount handheld bracket onto spout base. Tighten using

supplied hex wrench.

Attach hose to spout and handheld shower.

Once hand shower is attached turn on TUB FILLER and

test the diverter

Turn on water supplies and check all connections for leaks.

Check MANIFOLD connections for leaks.Remove foam

protector and apply sealant to under side edge on

ESCUTCHEON . Slide ESCUTCHEON down to finish floor.

Press into place.Clean up excess sealant.

APPLY SEALANT

FOAM PROTECTOR

Installation is complete.

6mm hex wrench

5T4000400ZZ0

6mm HEX WRENCH

2.5mm HEX WRENCH

13mm HEX WRENCH

2.5mm HEX WRENCH

14-05

Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean,

soft cloth after each use. Rinse completely with water and

dry any overspray. This will maintain the finish and avoid

water spotting.

To remove mineral deposits, use a 50/50 solution of white

vinegar and water. Do not allow the solution to soak on the

product.

Simichrome Polish® contains a protective film to enhance

maintenance and is helpful in preventing water spot

buildup. Follow instructions to ensure optimum results.

Never use an abrasive material such as a brush or scouring

pad to clean the surface. The use of abrasive cleaners,

cleansers or disinfectants will alter the surface finish and

void the warranty.

Do not allow certain materials such as toothpaste, cologne,

shaving cream, nail polish remover, vinegar, wine, drain

and glass cleaners to remain on the surface. Prolonged

contact will alter surface finishes and void the warranty.

We DO NOT recommend using any household cleaners

as many can cause damage to the finish.

Please see the website for care instructions for specific

finishes.

15122806 6 151228063

Applicable Standards/Codes

Installation Dimensions

IAPMO certified to meet or exceed the following:







4-1/2"

3-3/4"

1 5/16

2-1/2-14 NPT

MIN 2-3/4"

MAX 4-3/4"

Complete the installation of the Finished Floor. Tile as close

to the PLASTER GUARD as possible.Caulk between

Finished Floor and PLASTER GUARD.

When you are ready to install the TUB FILLER cut the

exposed part of the PLASTER GUARD flush with the

finished floor. Be careful not to damage the floor.

FINISHED FLOOR

8-1/4

11-5/8"

10-3/8

8-1/2"

36-3/4" - 39"

35-3/8

30-1/2"  32-3/4"

24-7/8"  27"

32-1/4" - 34-1/2"

1-1/2"

5-1/8

4

8-1/8

3-3/8

FINISHED FLOOR

ROUGH FLOOR

Turn off water supplies. With a wrench remove the center

TEST PLUG as shown in Figure A. If the TEST PLUGS

cannot be removed in one piece as shown in Figure A, the

lower half will have to be removed using the supplied 6mm

Hex Wrench as show in Figure B.

Repeat step for the second TEST PLUG.

Remove PLASTIC CAP from bottom of the TUB FILLER.

Before final installation, check that all sealing surfaces are

clean and that the two O-RINGS are installed in the

MOUNTING ADAPTER.Install the MOUNTING ADAPTER

into the MANIFOLD MOUNTING BASE.Install the four

MOUNTING SCREWS and WASHERS through the

MOUNTING PLATE and into the MANIFOLD MOUNTING

BASE. Do not tighten.Rotate the TUB FILLER right or left

to align with Tub.Tighten MOUNTING SCREWS supplied

with 6mm Hex Wrench to secure TUB FILLER.

FIGURE “A” FIGURE “B”

FRONT

6mm HEX WRENCH

FRONT

O-RING SEALS

REMOVE PLASTIC CAP

14-05

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.

For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757

Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-0433 fax: 508-381-6068

www.crosswaterlondon.com

email: [email protected]

Issue date: 20102020

2-15/16"

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crosswater Sanitärprodukte Handbücher

Crosswater

Crosswater LIBRA LB6117C Series Bedienungsanleitung

Crosswater

Crosswater UNION US-UN800 Bedienungsanleitung

Crosswater

Crosswater WS2001RC Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-20-T Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Crosswater

Crosswater 11-04 Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-15P-T Bedienungsanleitung

Crosswater

Crosswater US-SP380 Bedienungsanleitung

Crosswater

Crosswater KWC DOMO 10.061.033.000 Kurzanleitung

Crosswater

Crosswater Solo Produkthandbuch

Crosswater

Crosswater Berea 11-02-T Bedienungsanleitung

Crosswater

Crosswater 1000 Series Bedienungsanleitung

Crosswater

Crosswater Wisp US-WP418 Bedienungsanleitung

Crosswater

Crosswater KWC 10.441.004.000FL Handbuch

Crosswater

Crosswater BTW0241C Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL002 Bedienungsanleitung

Crosswater

Crosswater Belgravia Wall Union US-BL004 Bedienungsanleitung

Crosswater

Crosswater UNION US-UN399 Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL422 Bedienungsanleitung

Crosswater

Crosswater Darby 15-15P-T Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF135 Bedienungsanleitung

Crosswater

Crosswater MPRO US-PRO418 Bedienungsanleitung

Crosswater

Crosswater Darby 15-16-T Bedienungsanleitung

Crosswater

Crosswater INFINITY 500mm FURNITURE Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema