Crosswater MPRO US-PRO110 Bedienungsanleitung

Installation Instructions

4-3/4"

5-1/2"

15/8”

2-1/2"

1-1/4"

1-3/4"

US-PRO114

6-1/2"

2-3/8"

2-1/2"

1-1/4"

1-3/4"

US-PRO110

US-PRO110-K

6-3/4"

14-1/4"

10-1/8"

2-1/2"

1-1/4"

1-3/4"

US-PRO112

3/4"

3/4”

Adjustable

wrench

Channel

locks

Plumbers’ putty

or caulking

Flat head

screwdriver

Cross head

screwdriver

Hexagonal

key

MPRO Single-hole Basin Faucet US-PRO110 / US-PRO110-K

MPRO Single-hole Mini Basin Faucet US-PRO114

MPRO Vessel Faucet US-PRO112

Introduction

Installation notes

The faucets in this range are single flow (hot and cold water mix in the

body) and should therefore be supplied with hot and cold water at

balanced pressures. If the faucets are not supplied at balanced

pressures then the mixer will not function correctly.

The minimum water pressure required for these faucets is 20 psi. The

maximum water pressure is 60 psi beyond which pressure-reducing

valves must be installed.

The faucets are fitted with half-turn ceramic disc cartridges which

provide a good flow rate with very smooth movement.

IMPORTANT: Please read these instructions carefully before you

begin and retain for future reference. These instructions have been

prepared for your guidance, you must exercise due care at all

times.

Before beginning installation, check for any damage that may have

occurred during transport. Note: Damage claims cannot be made

during or after installation.

We do not accept responsibility for any problems that may occur

through incorrect installation.

Dimensions

Tools required

The installation must comply with all plumbing codes including

local

codes and be installed by a licensed plumbing contractor.

WARNING! Before installing a new faucet it is essential that the supply

pipes are thoroughly flushed in order to remove any remaining debris,

solder or other impurities. Failure to carry out this simple procedure

can cause problems or damage to the working of the faucet.

Installing shut-off valves on incoming supply lines is recommended

for ease of maintenance.

Turn off the main water supply before connecting to any existing

pipework or doing any maintenance.

WARNING! Please check for any hidden pipes and cables, electric

or otherwise,before drilling holes in a wall or floor.

Note:Illustrations not drawn to scale.

3/4"

HANDLE

WASHER

MIXER

BASE RING

C-SHAPED

BLACK

WASHER

FLEXIBLE

PIPES

C-SHAPED

RETAINING

PLATE

NOZZLE

FIXING

NUT

THREADED

STUD

BODY

CARTRIDGE

Replacement part

US-MCARP110

AERATOR

Replacement part

US-AERPROWS

HANDLE

BODY

RETAINING

NUT

COVER

HEXAGONAL

KEY

COVER

CAP

Note:

Generic illustration shown.

Note:

Generic illustration shown.

lShut off the water heating system then, with the main water

supply turned off, open the lowest hot and cold faucets and allow

to drain until the pipes are empty.

lScrew the flexible pipes into the body and fully hand tighten.

Be careful not to overtighten! The hot water should be

connected to the left inlet when the faucet is viewed from the

front.

lPlace the mixer in position to determine if any alteration to the

existing pipework is necessary.

lAfter making any necessary alterations, pass the mixer base ring

and washer over the flexible pipes and threaded stud to form a seal

on the counter/basin top.

lPass the flexible pipes and threaded stud through the hole in the

counter/basin and place the faucet into position.

lSlide the C-shaped black washer and then the C-shaped retaining

plate up the flexible pipes and secure with the fixing nut, finger

tight only.

lCheck that the faucet is positioned correctly and tighten the fixing

nut. The faucet needs to be fixed firmly but do not overtighten as

damage may be caused to the counter/basin.

Copper tails

lIf using copper tails they will need to be gently turned outwards,

then supported approximately halfway down and turned inwards

making the two pipes parallel thus allowing room for couplings. It

is recommended that 1/2” fittings be used to connect mixer to

supply pipes.

ATTENTION:Check all new connections for leaks.

lTurn on the main water supply, close all faucets except the new

mixer and as the system refills, check for leaks.

lOnce satisfied there are no leaks, switch on the heating system.

1Installation

Cleaning the cartridge

lThe concealed cartridge should give trouble-free service

however servicing is a straightforward process.

To remove the cartridge

lWith the water supply turned o, carefully remove the cover cap

and using a hexagonal key loosen the screw but do not remove.

lPull off the handle and unscrew the cover.

lUsing a 7/8” wrench, unscrew and remove the retaining nut.

lPull out the cartridge taking note of its orientation.

lWash the cartridge with clean running water, dry and lightly grease

the seal, (only use silicone grease).

lReplace the cartridge followed by the nut, cover and handle

2 Maintenance

Flow rate (PSI)

Flow rate (GPM)

100

0.2

0.4

0.6

0.8

1.0

1.2

20 30 40 50 60 70 80

Flow rate

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.

For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757

Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-0433 fax: 508-381-6068

www.crosswaterlondon.com

email: technical@crosswaterlondon.com

Issue date: 15092019

3 Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any

overspray. This will maintain the finish and avoid water spotting.

To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.

Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow

instructions to ensure optimum results.

Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or

disinfectants will alter the surface finish and void the warranty.

Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass

cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.

We DO NOT recommend using any household cleaners as many can cause damage to the finish.

Please see the website for care instructions for specific finishes.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crosswater Sanitärprodukte Handbücher

Crosswater

Crosswater US-AL7005CW Bedienungsanleitung

Crosswater

Crosswater Taos Deck-mount Tub Faucet with Handshower Trim... Bedienungsanleitung

Crosswater

Crosswater UNION US-UN399 Bedienungsanleitung

Crosswater

Crosswater Darby 15-15P-T Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-15P-T Bedienungsanleitung

Crosswater

Crosswater Solo Produkthandbuch

Crosswater

Crosswater US-ARC953 Bedienungsanleitung

Crosswater

Crosswater US-SP380 Bedienungsanleitung

Crosswater

Crosswater ATOLL SQUARE EXPOSED THERMO SHOWER VALVE... Bedienungsanleitung

Crosswater

Crosswater INFINITY 500mm FURNITURE Bedienungsanleitung

Crosswater

Crosswater Classic Console Series Bedienungsanleitung

Crosswater

Crosswater 28-07 Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-20-T Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC14 Bedienungsanleitung

Crosswater

Crosswater Leyden Robe Hook 14-51 Bedienungsanleitung

Crosswater

Crosswater WS2001RC Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC600 Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL440 Bedienungsanleitung

Crosswater

Crosswater US-PRO120 Bedienungsanleitung

Crosswater

Crosswater Belgravia Wall Union US-BL004 Bedienungsanleitung

Crosswater

Crosswater 11-04 Bedienungsanleitung

Crosswater

Crosswater Taos 17-19-T Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL422 Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC15 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema