CYP CH-507TX Bedienungsanleitung
CH-507TX & RX
HDMI to CAT5e/6 with LAN/IR/RS-232
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VS1 29/02/12 First Release
VR2 02/03/12 POE Supports only family's device
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Transmitter Front and Rear Panels..3
6.2 Receiver Front and Rear Panels .....5
7. D-Sub 9 Pin Denitions........................... 6
8. Connection Diagram ............................ 7
9. Specications ........................................ 8
10. Acronyms ............................................. 9
1
1. INTRODUCTION
The HDMI with RS-232 over Single CAT5e/CAT6 transmitter and receiver
set can send uncompressed audio/video over a single run of CAT5e/6
cable up to 100m with POE feature and the added benet of control
through the built-in RS-232 and IR ports and a bi-directional LAN
connection.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1× HDMI to CAT5e/6 (with LAN/IR/RS-232) Transmitter
• 1× CAT5e/6 to HDMI (with LAN/IR/RS-232) Reciever
• 1× IR Blaster
• 1× IR Receiver
• 1× 24 V/1.25 A DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
Input HDMI source equipment such as DVD/Blu-ray player and HDMI
equipped output display (TV or monitor).
2
5. FEATURES
• HDMI 1.4 with 3D, 4k×2k support, HDCP & DVI Compliant
• Supports CEC bypass
• Simultaneous transmission of uncompressed data over a single
100 m/328 ft CAT6/CAT5e cable
• Uncompressed video 1080p, 60 Hz, 36-bit
• Audio support up to 7.1CH & Dolby TrueHD, DTS-HD
• 5Play™ convergence: HDMI, LAN, POE & Control (IR & RS232)
• Installation Friendly
Note:
1. This system was tested with CAT-6E/23AWG cables, results may
vary with cables of a different specication.
2. The POE function is designed to support the same family type's
receiver devices, it is not designed to power other devices.
3. The POE function is designed to support the same family type of
device(here it means receiver) only. It is not design to power other
non-family type of devices.
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
RearFront
RS-232 In
LAN
HDMI In
HDMI to CAT5e/6 with LAN/IR/RS232
Transmitter
CAT5e/6 Out
Link
IR2 Extender
IR1 Blaster
DC 24V
Power
2 31 64 7 8 95
1HDMI In
Connect to HDMI source equipment such as a DVD or Blu-ray
player.
2LAN
Connect to an internet or network connection.
3RS-232 In
Connect to a PC or laptop with D-Sub 9 pin male cable for the
transmission of RS-232 commands.
4Power LED
This blue LED will illuminate when the device is connected to a
power supply.
5DC 24V
Plug the 24 V DC power supply into the unit and connect the
adaptor to an AC outlet.
6IR 1 Blaster
Connect to the supplied IR blaster cable for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be
controlled.
7IR 2 Extender
Connect to the supplied IR receiver cables for IR signal reception.
Ensure that remote being used is within the direct line-of-sight of
the IR extender.
4
8Link LED
The yellow LED will illuminate when both the input and output
signals are connected.
9CAT5e/6 Out
Connect to the reciever unit with a Single CAT5e/6 cable for
tranmission of all data signals.
5
6.2 Receiver Front and Rear Panels
RS-232 Out
LAN
HDMI Out
CAT5e/6 to HDMI with LAN/IR/RS232
Receiver
RearFront
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
2 31 65 7 84
1HDMI Out
Connect to a HDMI equipped TV/monitor for display of the HDMI
input source signal.
2LAN
Connect to a PC or Laptop to the Internet or network connection.
3RS-232 Out
Connect to the device that is to be controlled (via D-Sub 9 pin
female cable) by RS-232 commands.
4Power LED
This blue LED will illuminate when the device is connected to a
power supply.
5IR 2 Blaster
Connect to the supplied IR blaster cable for IR signal transmission.
Place the IR blaster in direct line of sight of the equipment to be
controlled.
6IR 1 Extender
Connect to the supplied IR receiver cables for IR signal reception.
Ensure that remote being used is within the direct line-of-sight of
the IR extender.
7Link LED
The yellow LED will illuminate when both the input and output
signals are connected.
8CAT5e/6 In
Connect to the transmitter unit with a Single CAT5e/6 cable for
tranmission of all data signals.
Andere Handbücher für CH-507TX
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere CYP Empfänger Handbücher
CYP
CYP PUV-1810RX-AVLC Bedienungsanleitung
CYP
CYP PRO-HDMIFO-KIT Bedienungsanleitung
CYP
CYP COH-TX1 Bedienungsanleitung
CYP
CYP CH-2603RX Bedienungsanleitung
CYP
CYP PU-107 Bedienungsanleitung
CYP
CYP AVIP-P5104R-B1C Bedienungsanleitung
CYP
CYP PUV-1650TX Bedienungsanleitung
CYP
CYP CH-2540RX Bedienungsanleitung
CYP
CYP CH-526RX Bedienungsanleitung
CYP
CYP CH-527RXVBD Bedienungsanleitung
CYP
CYP CH-1507TX Bedienungsanleitung
CYP
CYP 5-Play HDBaseT PU-507WPRX Bedienungsanleitung
CYP
CYP HDBaseT 5Play PUV-1510RX Bedienungsanleitung
CYP
CYP PU-1109KIT Bedienungsanleitung
CYP
CYP 5-Play HDBaseT PU-507WPRX Bedienungsanleitung
CYP
CYP CH-2535TX Bedienungsanleitung
CYP
CYP CA-HDMI250R Bedienungsanleitung
CYP
CYP PU-607BD-RX Bedienungsanleitung
CYP
CYP RXWPBD Bedienungsanleitung
CYP
CYP PUV-3050RX-UA Bedienungsanleitung
