Daewoo RCC-9508HR Bedienungsanleitung
March.2006
Service Manual
VACUUM CLEANER
MODEL : RCC-9508HR
DAEWOO ELECTRONICS CO., LTD
S/M No : RCC9508001
Page
1.SPECIFICATIONS ------------------------------------------------------------
-
2
2. EXTERNAL VIEWS
2-1. ASSEMBLY ------------------------------------------------------------------------------------- 3
3. DIAGRAM
3-1. WIRING DIAGRAM --------------------------------------------------------------- 4
3-2. CIRCUIT DIAGRAM ------------------------------------------------------------------- 5
4. TRBOUBLE SHOOTING GUIDE ----------------------------------------- 67
5. DISASSEMBLING AND TREATMENT
5-1. CLEANER ASSEMBLY ---------------------------------------------- 89
5-2. BODY ASSEMBLY ------------------------------------------------------------ 10
5-3. COVER ASSEMBLY ------------------------------------------------ 11
5-4. CORDREEL ASSEMBLY ------------------------------------------------ 12 13
5-5. MOTOR ASSEMBLY ---------------------------------------------------------------- 14
5-6. FILTER EXHAUST ASSEMBLY ----------------------------------------------------------
-
15
5-7. HOSE ASSEMBLY ---------------------------------------------------------------- 16 17
5-8. DUST BOX ASSEMBLY ---------------------------------------------------------------- 18 19
5-9. PIPE ELBOW ASSEMBLY ---------------------------------------------------------------- 20
5-10. BRUSH SLIM ASSEMBLY -------------------------------------------------------------- 21
5-11. BRUSH WIDE ASSEMBLY -------------------------------------------------------------- 22
5-12. BRUSH FLOOR ASSEMBLY ------------------------------------------------------------
-
23
5-13. BRUSH PEDAL ASSEMBLY ------------------------------------------------------------
-
24
6. EXPLODED VIEW AND PARTS LIST
6-1. CLEANER ASSEMBLY ---------------------------------------------- 25 26
6-2. BODY ASSEMBLY ----------------------------------------------- 27 28
6-3. COVER SIDE ASSEMBLY ----------------------------------------------- 29
6-4. CASE MOTOR ASSEMBLY ----------------------------------------------------- 30 31
6-5. CORDREEL ASSEMBLY ------------------------------------------------------ 32 33
6-6. COVER BODY ASSEMBLY ----------------------------------------------------- 34
6-7. COVER TOP ASSEMBLY ----------------------------------------------------- 35
6-8. DUST BOX ASSEMBLY ----------------------------------------------------- 36 37
6-9. FILTER EXHAUST ASSEMBLY ----------------------------------------------------- 38
6-10. HOSE ASSEMBLY -------------------------------------------------------- 39 40
6-11. PIPE ELBOW ASSEMBLY ---------------------------------------------------------- 41 42
6-12. PIPE ASSEMBLY ---------------------------------------------------------- 43
6-13. BRUSH SLIM ASSEMBLY -------------------------------------------------------- 44 45
6-14. BRUSH WIDE ASSEMBLY -------------------------------------------------------- 46 47
6-15. BRUSH FLOOR ASSEMBLY -------------------------------------------------------- 48 49
6-16. BRUSH PEDAL ASSEMBLY -------------------------------------------------------- 50 56
CONTENTS
1. SPECIFICATIONS
MODEL RCC-9508HR
Rating AC 230V, 50Hz
Watts 1800W
Weight(body) 5.5Kg
Dimension
(WxHxD) 430 X 295 X 295 mm
Anti-biotic
NanoSilver Dust Box
Hose PVC transparency
1.6M
Pipe One touch
Elbow Pipe ○
Main Brush Slim+Wide+Front
Pedal
Sub Brush Dusting/Crevice/
Upholstery
Exhaust Filter System HEPA Filter
Functional Filter Carbon Deodorization Filter
convenience transparency dust box / 360 degree rotational hose /
stand keeping and body keeping temporary / convnient handle for moveing
- 2 -
RCC-9508HR
A- Dust Box ○
B- System HEPA Filter ○
C- High Quality LED Display ○
D- Hose (PVC 1.6M) ○
E- Elbow Pipe ○
F- Pipe (One touch aluminum) ○
G- Main Brush (Slim+Wide Brush) ○
H- Main Brush (Floor Brush) ○
I - Main Brush (Pedal Brush) ○
J- Dusting, Crevice Nozzle ○
K- Upholstery nozzle ○
Part Name
2-1. ASSEMBLY
2. EXTERNAL VIE
W
- 3 -
3. DIAGRAM
1) MODEL
1) LED PCB
3-1. WIRING DIAGRAM
3-2. CIRCUIT DIAGRAM
- 4 -
2) MAIN PCB
- 5 -
4. Trouble Shooting Guide
☞
CAUTION ! Please surely unpluged power plug before repairing.
TROUBLE CAUSE CHECKING COUNTERMEASURE
Dust box is full with dust Dust Box (See 5-8) Remove the dust
Dust box is installed incorrectly Dust Box (See 5-8) Reinstall dust box
Filter in dust box is clogged with dust Dust Box (See 5-8) Cleaning→drying→using
Exhaust filter is clogged with dust Exhaust Filter (See 5-6) Cleaning→drying→using
Defective motor Motor (See 5-5) Replace the motor
Filter in motor assembly is clogged with dust Motor (See 5-5) Clean the filter
Pressure switch is defective Body (See 5-2) Replace pressure switch
Clogging or tear in hose Hose (See 5-7 ) Remove obstacle or replace the hose
Telescopic/elbow pipe is clogged with large dust Elbow Pipe (See 5-9) Remove obstacle
Brush nozzle or hose is clogged with large dust Brush (See 5-7,10~12) Remove obstacle
Dust Box (See 5-8) Remove dust
PCB (See 5-1) Replace PCB
Hose (See 5-7 ) Remove obstacle
Elbow Pipe (See 5-9) Remove obstacle
Breaking in power cord Replace power cord
Bad contacts in cord reel assembly Repair bad contact
Breaking of connections in cord reel assembly Repair Disconnection
Defective terminal connection of PCB in body PCB (See 5-1) Check terminal connection state
Wire disconnection in body Body (See 5-2) Repair Disconnection
Pressure switch disconnection in body Body (See 5-2) Repair Disconnection
Defective terminal contact between body and hose Body, Hose (See 5-2, 5-7) Repair bad contact
Breaking of connections in hose Replace hose
Defective terminal contact in hose handle Repair bad contact
Defective slide volume in hose handle Replace slide volume
Defective PCB PCB (See 5-1) Replace PCB
Defective contact between PCB and motor/cord reel PCB (See 5-1) Repair bad contact
Motor out Motor (See 5-5) Replace Motor
Fuse disconnection Cord reel (See 5-4) Replace fuse
Broken reel sping of cord reel Cord reel (See 5-4) Replace Cord reel
Power cord is interwined Cord reel (See 5-4) Repair interwinement
Power cord is not
wound up
Suction power
is weak
(Red light blink)
Vacuum cleaner
does not work
Motor does not stop
even if switch off
Red light on the body
blink and suction
power is low and high
repeatedly
Motor protect system will be executed when dust
box is filled up with dust or hose is clogged
with obstacle over 15 seconds.
Cord reel (See 5-4)
Hose (See 5-7 )
Defective PCB PCB (See 5-1) Replace PCB
Be careful when breaking up the cord reel, the reelspring may spring out of the spring cover.
CAUTION
- 11 -
TROUBLE CAUSE CHECKING COUNTERMEASURE
Abrasion of the roller tire of cord reel Cord reel (See 5-4) Replace tire
Broken lever Cord reel (See 5-4) Replace lever
Lever spring broken away from cord reel bracket Cord reel (See 5-4) Repair lever spring
Bobbin is transformed Cord reel (See 5-4) Replace bobbin
Bracket is transformed Cord reel (See 5-4) Replace bracket
Lever is pushed by handle Cover (See 5-3) Repair handle
Brush does not rotate
any direction
Power cord does
not stop at an
arbitraty position
Clogged impurites in rotational part Brush (See5-10) Remove impurites
- 12 -
5. DISASSEMBLING AND TERATMENT
◈NOTE
First of all take cover top(5) out of cover Assy(4) and then take LED terminal out of main PCB
If do not remove LED terminal, main PCB may be damaged.
1) Remove dust box Assy(1) form body assembly(6).
2) Open cover filter(2) of cover Assy(4) then unscrew 6 screws(3).
3) Remove cover top(5) form cover assembly(4).
4) Remove cover Assy(4) from body assembly(6).
5) Remove cord reel Assy(7) and Motor Assy(8) from body assembly(6)
5-1. CLEANER ASSEMBLY
- 8 -
1) Check dust leakage between dust box(1) and clearner body(7) (Cause of defective motor).
2) Check inlet(9) of clearner body(7) clogged with dust (Cause of low suction power).
3) Check connection between wire connector(2) of cord reel and PCB (Cause of malfunction).
4) Check connection between wire connector(3) of motor and PCB (Cause of malfunction).
5) Check connection between wire connector(4) of body and PCB (Cause of malfunction).
6) Check connection between wire connector(5) of pressure switch and PCB (Cause of malfunction).
7) Check PCB circuit (Cause of of malfunction).
8) Check connection between hose adapter(10) and body(7) (Cause of malfunction).
- 9 -
Inhaltsverzeichnis
Andere Daewoo Staubsauger Handbücher
Daewoo
Daewoo Cyclone Freedom Pro Bedienungsanleitung
Daewoo
Daewoo TORNADO PET Bedienungsanleitung
Daewoo
Daewoo CYCLONE DIGI ONE Bedienungsanleitung
Daewoo
Daewoo Cyclone Freedom FLR00010 Bedienungsanleitung
Daewoo
Daewoo DAVC 90-20L Bedienungsanleitung
Daewoo
Daewoo HURRICANE CAT 3 Bedienungsanleitung
Daewoo
Daewoo RC-350BKN Bedienungsanleitung
Daewoo
Daewoo RC-400B Bedienungsanleitung
Daewoo
Daewoo RC-370F Bedienungsanleitung
Daewoo
Daewoo RC-4008S Bedienungsanleitung
Daewoo
Daewoo RC-6003F Bedienungsanleitung
Daewoo
Daewoo RCP-1000 Bedienungsanleitung
Daewoo
Daewoo RC-382A Bedienungsanleitung
Daewoo
Daewoo RC-320B Bedienungsanleitung
Daewoo
Daewoo FLR00046 Bedienungsanleitung
Daewoo
Daewoo RCU-3006 Series Bedienungsanleitung
Daewoo
Daewoo RCG-100 Bedienungsanleitung
Daewoo
Daewoo Daema RCW-120AW Bedienungsanleitung
Daewoo
Daewoo A2161 Bedienungsanleitung
Daewoo
Daewoo RC-4008BA Bedienungsanleitung
Beliebte Staubsauger Handbücher anderer Marken
Bissell
Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung
Panasonic
Panasonic MC-YL637S147-AE Bedienungsanleitung
NEFF
NEFF N17XH10 0 Series Bedienungsanleitung
LG
LG A9 Series Bedienungsanleitung
Oreck
Oreck Cordless Captura BK51700 Series Bedienungsanleitung
Kogan
Kogan KAVACROBVWA Bedienungsanleitung
