DFI G586OPB Bedienungsanleitung

G586OPB

Rev. 0 +

System Board

User’s Manual

-D27850601-

No part of this document may be copied, reproduced in

any form or by any means or used to make any trans-

formation/adaptation without the prior written consent

of DFI, Inc.

DFI, Inc. makes no warranties with respect to this

documentation and disclaims any implied warranties of

merchantability, quality, or fitness for any particular

purpose. The information in this document is subject to

change without notice. DFI, Inc. reserves the right to

make revisions to this publication and to make changes

to any and/or all parts of its content, at any time,

without obligation to notify any person or entity of such

changes. Further, DFI, Inc. assumes no responsibility

for any errors that may appear in this document.

DFI is a registered trademark, and G586OPB is a

trademark of Diamond Flower, Inc. All other product

names mentioned are trademarks or registered trade-

marks of their respective companies.

vFCC Statement on Class B

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

the receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio TV

technician for help.

Notice:

1. The changes or modifications not expressly

approved by the party responsible for compliance

could void the user's authority to operate the

equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

v Table of Contentsv

Introduction ..............................................................................

Features and Specifications .........................................

Package Checklist ........................................................

Installation Overview ...............................................................

Preparing the Area ..............................................................

Handling the System Board ................................................

Tips in Handling the System Board ..............................

Hardware Installation...........................................................

Memory Installation .......................................................

Installing the Modules ............................................

Board Configuration ......................................................

Jumper Settings for Flash EPROM, PS/2 Mouse

and Display Type....................................................

Jumper Settings for Parallel Port ...........................

Cache Configuration .....................................................

Jumper Settings for Cache Memory ......................

CPU Installation ............................................................

Jumper Settings for CPU .......................................

Installing Upgrade CPUs .......................................

Built-in Ports ........................................................................

Serial Ports ...................................................................

Parallel Port ..................................................................

Floppy Disk Drive Connector ........................................

IDE Hard Disk Connector .............................................

PS/2 Mouse Port ...........................................................

Installing Expansion Cards ..................................................

Installing the System Board ................................................

1-1

1-2

1-5

2-1

2-2

2-3

2-6

2-7

2-8

2-11

2-13

2-14

2-17

2-18

2-21

2-26

2-27

2-28

2-30

2-31

2-34

2-35

2-36

3-1

3-2

3-5

3-7

3-8

3-9

3-16

3-17

3-18

3-19

3-20

4-1

5-1

A-1

B-1

C-1

D-1

E-1

F-1

G-1

Initial Setup Program ..............................................................

Award BIOS CMOS Setup Utilities .....................................

Standard CMOS Setup .................................................

BIOS Features Setup ....................................................

Chipset Features Setup ................................................

Power Management Setup ...........................................

PCI Configuration Setup ...............................................

Load BIOS Defaults ......................................................

Load Setup Defaults .....................................................

Password Setting ..........................................................

IDE HDD Auto Detection ..............................................

Save & Exit Setup .........................................................

Exit Without Saving .......................................................

IDE Device Drivers ..................................................................

Troubleshooting Checklist .....................................................

Appendix A:Types of Modules ..............................................

Appendix B:System Error Report .........................................

Appendix C:Memory & I/O Maps ..........................................

Appendix D:PCI I/O Pin Assignments ..................................

Appendix E:ISA I/O Pin Assignments ..................................

Appendix F:Connector Pin Assignments ............................

Appendix G:Award BIOS Hard Disk Table ...........................

PCI/ISASystemBoard

1-1 uIntroduction

vIntroduction

The G586OPB system board offers several advanced

features integrated into the system board. Its design is

based on the new Peripheral Component Interconnect

(PCI) local bus and Industry Standard Architecture

(ISA) standards.

The G586OPB supports a 321-pin Zero Insertion Force

(ZIF) CPU socket for PentiumTM processors running at

75MHz, 90MHz, 100MHz, 120MHz, 133MHz or

150MHz frequency. This ZIF socket allows users to

easily upgrade their CPUs. It also supports a Flash

EPROM for easy BIOS upgrades. Flash EPROM is a

memory chip for the storage of BIOS which can be

erased in bulk or modified using a software utility.

The G586OPB is equipped with three PCI slots, three

ISA slots and one shared PCI/ISA slot.

Equipped with two built-in PCI IDE connectors, the

G586OPB system board can control four drives and

supports fast Mode 3 and 4 hard drives and hard drives

larger than 528MB under DOS. The system board is

also equipped with two NS16C550A-compatible serial

ports, an ECP/EPP parallel port, a floppy disk drive

controller, and one mini-DIN-6 connector for the PS/2

mouse.

The G586OPB can support 2MB to 128MB of memory

using 256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 and

8Mx36 72-pin SIM modules.

G586OPB

Features and Specifications

Introduction u1-2

Processor

•Intel PentiumTM 75/90/100/120/133/150MHz

Chipset

•OPTI: Viper chipset

Energy Efficient Design

•Supports 3.3V CPUs

•Supports system power management

•Supports CPU stopped clock

Power Management

•Three power-saving stages: Doze, Standby and

Suspend

•Microsoft APM 1.1 supported

PCI IDE Interface

•Fast PCI local-bus interface

•Supports Mode 3, 4 Enhanced IDE

•Two IDE connectors to control four drives (e.g.

two HDDs, one tape drive and one CD-ROM)

Super I/O Interface

•Two NS16C550A-compatible serial ports

•PS/2 mouse port

•One parallel port with EPP and ECP support

•Supports 360KB, 720KB, 1.2MB, 1.44MB and

2.88MB floppy drives

•Uses NS PC87332VF super-I/O controller

BIOS

•Award Flash BIOS supports Windows 95 Plug &

Play

•Supports enhanced IDE larger than 528MB under

DOS (LBA mode only)

PCI/ISASystemBoard

1-3 uIntroduction

Architecture

•PCI/ISA

Cache Memory

•256K, 512K or 1MB direct map write-back or

write-through cache

•Uses 32Kx8, 64Kx8 or 128Kx8 SRAM

•Supports 3.3V or 3.3V/5V mixed voltage SRAM

Memory Onboard

•Up to 128MB

•Four 72-pin SIMM sockets

•Supports single and/or double density SIMMs

•256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 or

8Mx36 SIMMs

•Supports 60ns or 70ns fast page mode DRAM or

EDO DRAM

Expansion Slots

•Three dedicated PCI slots

•One shared PCI/ISA slot

•Three dedicated 16-bit ISA slots

Due to the height of the heat sink, once the 3.3V

Pentium Upgrade Processor is in place, you cannot

install full-length add-in cards in slot connectors 1,

2 and 4 (ISA), and 1 and 2(PCI). These slots are

limitted to 2/3 length of add-in cards.

ZIF Socket

•321-pin ZIF socket (Intel Socket 7)

Board Dimensions

•33cm (12.87") x 22cm (8.58")

Baby AT form factor

G586OPB

Package Checklist

The G586OPB package contains the following items:

•The G586OPB system board

•The G586OPB user’s manual

•One set of IDE driver diskettes

•One 34-pin floppy disk drive cable

•Two 40-pin IDE hard disk cables

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial and mouse port

cables

If any of these items are missing or damaged, please

contact your dealer or sales representative for assistance.

Introduction u1-4

PCI/ISASystemBoard

vInstallation Overview

This chapter summarizes the steps in installing the

G586OPB system board into your system unit. It also

includes a description of the area in which you must

work and directions for memory installation. Before

installing the system board, obtain the memory you plan

to install. Please refer to the memory chart, on pages 2-3

and 2-4, for the number and type of SIM modules

needed for the amount of memory you require.

Preparing the Area

Before unpacking the system board, make sure the

location you have selected is relatively free of dust and

static electricity. Excessive exposure to dust, static

electricity, direct sunlight, excessive humidity, extreme

cold, and water can damage the operational capabilities

of your system board. Avoid placing the unit on soft

surfaces such as beds and carpeted floors which can

hinder air circulation. These areas also attract static

electricity which can damage some circuits on your

system board.

Make sure that the power source has a properly

grounded, three-pronged socket. It is essential that the

power connection be properly grounded for correct

functioning of your system board. For further protection,

we recommend that you use a surge suppressor. This

will protect the system board from damage that may

result from a power surge on the electrical line.

Move items that generate magnetic fields away from

your system board, since magnetic fields can also

damage your system board. Once you have selected the

2-1 uInstallation Overview

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI NP900-B16C Bedienungsanleitung

DFI

DFI WL171/WL173 Bedienungsanleitung

DFI

DFI LanParty X58-T3eH8 Bedienungsanleitung

DFI

DFI LanParty 925X-T2 Bedienungsanleitung

DFI

DFI LanParty UT RDX200 series Bedienungsanleitung

DFI

DFI G586IPV Bedienungsanleitung

DFI

DFI AL051 Bedienungsanleitung

DFI

DFI MB630-CRM Bedienungsanleitung

DFI

DFI AK74-SC Bedienungsanleitung

DFI

DFI CP330-NRM Bedienungsanleitung

DFI

DFI Blood-Iron G41-T33 Bedienungsanleitung

DFI

DFI CR100-CRM Bedienungsanleitung

DFI

DFI LanParty LT P35 Bedienungsanleitung

DFI

DFI CW35-TC Bedienungsanleitung

DFI

DFI BT253 Bedienungsanleitung

DFI

DFI CL60-LX Bedienungsanleitung

DFI

DFI KD330-H110 Bedienungsanleitung

DFI

DFI GIC88-B Bedienungsanleitung

DFI

DFI LT600-DR/D/L Bedienungsanleitung

DFI

DFI NB80-EA Bedienungsanleitung

DFI

DFI P2XBL/D Bedienungsanleitung

DFI

DFI CA64-TC Bedienungsanleitung

DFI

DFI QB701-B Series Bedienungsanleitung

DFI

DFI G586OP Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung