Dji GOGGLES Racing Edition Bedienungsanleitung

DJI GOGGLES

Racing Edition

Quick Start Guide

V1.0

DJI Goggles Racing Edition

DJI Goggles Racing Edition (hereafter abbreviated as “DJI Goggles”)are equipped

with high-performance displays and an ultra-low latency video downlink for use

with DJITM aircraft, giving you a real-time aerial First Person View (FPV) experience.

DJI Goggles can also be used to display HD videos, bringing you an immersive

high-definition viewing experience. DJI Goggles support head tracking, allowing

aircraft and gimbal to be controlled using head movements, introducing a new

style of flying.*

The DJI Goggles Racing Editionfeatures the advanced OCUSYNCTMvideo

transmission, supporting both theAnalog Video Downlink and 2.4 / 5.8GHz

dual-band Digital Video Downlink, providing a high video downlink performance

with as low as 50ms latency and up to 2km transmission distance, a variety of

Antennas can be usedfor more application scenarios. For third-party racing aircraft,

DJI OcuSync Air Unit can be used directly with DJI Goggles to provide you with

acamera, video transmission, controls and displays integrated, high-quality racing

flight experience.

1. Touch Panel

2. Headband

3. Charging Status Indicator

4. Micro USB Port

5. Headband Knob

6. Speaker

7. Power Button

8. Battery Level Indicators

9. Back Button

10. Function Button

11. Link Button

12. Linking Status Indicator

13. IPD (Interpupillary

Distance) Knob

14. Lens

15. Proximity Sensor

16. Headband Buckle

17. Heat Vent

18. Micro SD Card Slot

19. 3.5 mm Audio Port

20. HDMI Type-D Port

21. Speaker

22. SMAAntenna Port

1. Camera Port

Connect with the DJI OcuSync Camera. Note

that both this port and the camera connector

plug are customize Type-C interface and they

are not compatible with third-party equipment.

2. SBUS Port

Connect with the 3 in 1 Cable(power, S.Bus,

UART), and connect to power, flight controller

and the OSD port based on the sequence

below.

RED: Power

BLACK: Power GND

GRAY: UART RX(Connects toOSD)

WHITE: UART TX (Connects toOSD)

BROWN: GND

YELLOW: SBUS(Connects toFlight Controller

RX)

3. Micro SDCard Slot

Insert Micro SD Card to store the video

recorded.



4. Antenna Ports

Used to attach the Air Unit antennas.

5. Micro USB Port

Connects to your PC for firmware

upgradesthrough the DJI Assistant 2.

6. PPM Port

Connects to the aircraft’s gimbal with the

PPM Cable to control the aircraft or gimbal by

DJI Goggles. (supported later)

7. Link Button

Press this button to link the DJI OcuSync Air

Unit with the DJI Goggles.

8. Linking Status Indicator

Indicate the linking status of the DJI OcuSync

Air Unit and the DJI Goggles.

Module Connections

Analog Video Downlink

Install the pagoda antenna (SMA interface) to the SMA Port of DJI Goggles directly.

The provided pagoda antenna (SMA interface) also support two-way

digital transmission.A directional antenna with higher gain can be used

for better analogue transmission performance,.

Digital Video Downlink

When using the Digital Video Downlink, In addition to install the pagoda antenna

(SMA interface) to the SMA Port of DJI Goggles, you will also need to install the DJI

OcuSync Air System on a third-party racing aircraft to work with DJI Goggles. Refer

to the below connection illustration and then mount the modules onto the aircraft.

z It is recommended to use a lighter dipole antennawithin a short

distance flight, while a pagoda antenna (SMA interface) or a

cylindrical antenna is recommended when the flight distance is 100 m

or more.

z It is recommended to mount the DJI OcuSync Air Unit with its screw

side facing down.

z The SBUS Port and the PPM Port on the Air Unit are only used when

transmitting the remote control signal, these ports are not need to be

connected if only video downlink is used.

z Place the two antennas on the Air Unit in a mutually vertical manner

and with at least 30mm apart. Note that avoidinggood conductor

block at the antenna level, and keep the bottom of the antennafrom

the good conductor (cable, carbon fiber frame, battery and metal,

etc.) at least 25mm.

You can connect the coach port of a third-party remote controllerand the audio

port onDJI Gogglesthrough the coach cable to transmit the control signal to the

racing aircraft when using the Digital Video Downlink

Installation and Wearing

Check the Battery Level and Charging

Press once to check the battery level.

Press once, then again and hold to turn on/off.

The Battery is fully charged when the Charging Status Indicator or the BatteryLevel

Indicators turn off.

Charge time: ~ 4 hours Maximum run-time: ~ 6 hours

Activation and Connection

First-time activation is required before using your new DJI Goggles.

Ensure all devices are powered on and that the Aircraft is linked with the Remote

Controller. Make sure both are updated to the latest firmware versions.

MAVICTMSeries

INSPIRETM 2

PHANTOMTM 4

Series

SPARKTM**

INSPIRESeries

PHANTOM 4 PRO+

PHANTOM 4 ADVANCED+

Video Play

Device

OCUSYNCTM Micro USB cable HDMI cable HDMI cable

Press the Link

Buttons on the

Mavic Pro and DJI

Goggles, or enter

Tools > Setting >

Linking Setting

toconnect.

* Prepare an OTG

cable and connect it

to the Micro USB port

of the remote

controller.

Live view only.

Follow the steps below to link with the third-party racing aircraft.

1. Power on the DJI OcuSync Air Unit, press the link button on the air unit with an

appropriate tool when the linking status indicator is solid green, the indicator

will turn solid red when the air unit is waiting for linking.

2. Power on the DJI Goggles, directly press the link button with an appropriate

tool in the main menu, or swipe downward with two fingers on the touch panel

to enter the shortcut menu and select RacingDrone (Digital)> Linking Settings.

Inhaltsverzeichnis

Andere dji Drohnen- und Quadcopter-Zubehör Handbücher

dji

dji Avata ND8 Bedienungsanleitung

dji

dji BTU Bedienungsanleitung

dji

dji Goggles Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji Motion Controller Combo Bedienungsanleitung

dji

dji ZENMUSE L1 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji E800 Bedienungsanleitung

dji

dji RC 2 Bedienungsanleitung

dji

dji ZENMUSE L2 Bedienungsanleitung

dji

dji ZENMUSE XT S Bedienungsanleitung

dji

dji RC 2 Bedienungsanleitung

dji

dji Ronin Series Battery Power Distributor Bedienungsanleitung

dji

dji OSMO ACTION 3 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji Takyon Updater Bedienungsanleitung

dji

dji MATRICE 300 RTK Bedienungsanleitung

dji

dji ZENMUSE H20T Bedienungsanleitung

dji

dji AGRAS T40 Bedienungsanleitung

dji

dji Phantom 4 RTK Bedienungsanleitung

dji

dji Osmo Z-Axis Bedienungsanleitung

dji

dji MG Bedienungsanleitung

dji

dji FPV GOGGLES Bedienungsanleitung

dji

dji MATRICE 30 Series Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Bedienungsanleitung

ParaZero

ParaZero SafeAir Mavic Bedienungsanleitung

JT SS125 Bedienungsanleitung

RunCam

RunCam Phoenix HD Bedienungsanleitung

DRS

DRS DRS-M210-V2 Bedienungsanleitung

Kogan

Kogan 4K GALAXY Bedienungsanleitung

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Bedienungsanleitung

Flycolor

Flycolor X-Cross Mini 4in1 Bedienungsanleitung

ParaZero

ParaZero SafeAir Phantom Bedienungsanleitung

HOBBYEAGLE

HOBBYEAGLE A3 Mini Bedienungsanleitung

TCMM RC

TCMM RC AC 220 Bedienungsanleitung

iKarus

iKarus Profi Gyro Bedienungsanleitung

R2TECK

R2TECK NEXG1 Bedienungsanleitung

Hesai

Hesai Pandar40P Bedienungsanleitung

Flycolor

Flycolor X-Cross HV 2 Series Bedienungsanleitung

CZZN

CZZN GL60 ZOOM Bedienungsanleitung

PowerVision

PowerVision PowerEgg Bedienungsanleitung

A2Z Drone Delivery

A2Z Drone Delivery RDS1 Bedienungsanleitung

dji GOGGLES Racing Edition Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken