Edelbrock Russell 651107 Bedienungsanleitung

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock Honda TRX300EX Betriebsanleitung

Edelbrock

Edelbrock 6893 Bedienungsanleitung

Edelbrock

Edelbrock 6567 Bedienungsanleitung

Edelbrock

Edelbrock 70080 Bedienungsanleitung

Edelbrock

Edelbrock 5734 Bedienungsanleitung

Edelbrock

Edelbrock Victor Jr. 70067 Bedienungsanleitung

Edelbrock

Edelbrock 5786 Bedienungsanleitung

Edelbrock

Edelbrock Performer RPM 7167 Bedienungsanleitung

Edelbrock

Edelbrock Performer 2261 Bedienungsanleitung

Edelbrock

Edelbrock 15041 Bedienungsanleitung

Edelbrock

Edelbrock 5776 Bedienungsanleitung

Edelbrock

Edelbrock 6502 Bedienungsanleitung

Edelbrock

Edelbrock 6566 Bedienungsanleitung

Edelbrock

Edelbrock 68003 Bedienungsanleitung

Edelbrock

Edelbrock 15016 Bedienungsanleitung

Edelbrock

Edelbrock Nitrous Refill Station 78000 Bedienungsanleitung

Edelbrock

Edelbrock 72285 Bedienungsanleitung

Edelbrock

Edelbrock Russell R09392S Bedienungsanleitung

Edelbrock

Edelbrock 2994 Bedienungsanleitung

Edelbrock

Edelbrock Honda TRX450R Betriebsanleitung

Edelbrock

Edelbrock 6700 Bedienungsanleitung

Edelbrock

Edelbrock 60509 Bedienungsanleitung

Edelbrock

Edelbrock Performer-Plus 2157 Bedienungsanleitung

Edelbrock

Edelbrock 5223 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung

©

2008 Edelbrock Corporation

Brochure No. 63-651107

Catalog #651107

Rev. 3/08 - AJ/mc

Page 1

CHRYSLER & DODGE 5.7L & 6.1L HEMI FUEL HOSE KIT

For ‘06-‘08 Chargers; ‘05-‘08 Magnums & ‘05-‘08 300Cs

Catalog #651107

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new fuel hose assembly. If you have any questions, please call our

Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday - Friday, Pacific Standard Time or e-mail us at

[email protected].

TOOLS & SUPPLIES RECOMMENDED

❑EFI Fuel Disconnect Tool ❑Shop Towels/Rags

❑ 11/16” Wrench

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in

poor performance and engine or vehicle damage.

WARNING:

MAKE SURE TO DISCONNECT YOUR BATTERY TO AVOID THE

POTENTIAL FOR SPARKS IN THE WORK AREA!

INSTALLATION

1. Disconnect negative cable from battery in the trunk of the

vehicle and wait for fuel pressure to drop.

2. Remove engine cover by pulling upwards (The engine cover

is retained by rubber grommets).

3. Remove the factory push-on type fuel fitting on the fuel rail

by depressing the plastic clips located on the sides of the

fuel fitting (Figure 1). Use shop rags to catch any fuel that

might spill from the fuel fitting removal process.

4. Remove the fuel hose from the hard tube line located on the

chassis by using a fuel disconnect tool. (Figure.2) Use shop

rags to catch any fuel that might spill from the fuel hose

removal process.

5. Ensure that the Russell EFI push-on fittings are properly

tightened on the Russell fuel hose assembly. Install Russell

fuel hose assembly on the vehicle with the 5/16” fitting

(smaller of the two) on the chassis side and the 3/8” fitting

on the fuel rail side. Push on the Russell EFI fittings until the

plastic clip is fully seated on the fuel supply tube and the

fuel rail tube. Tug on the push-on fittings to ensure a proper

connection. (Figure 3).

6. Once the Russell Hose has been installed, reconnect the

negative battery cable and turn the ignition key to the “on”

position to allow fuel pressure to build. Start the vehicle and

let idle while watching for fuel leaks.

7. Re-install the engine cover.

FIGURE 1

FIGURE 2

FIGURE 3

Edelbrock Corporation • 2700 California St. • Torrance, CA 90503

Tech Line: 800-416-8628 • E-Mail: [email protected]