Ekwb EK-FC GV100 PRO Bedienungsanleitung

INSTALLATION MANUAL

EK-FC GV100 PRO

GPU WATER BLOCK

- 2 -

This product is compatible with Nvidia Quadro GV100 graphic card.

It is intended for installation only by expert users. Please consult with

a qualiﬁed technician for installation. Improper installation may result

in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor

their installation. The following instructions are subject to change

without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice,

disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic

guidelines:

Please carefully read the manual throughly before beginning

with the installation process!

Please remove your graphics card from computer to assure

safest mounting process in order to prevent any possible

damages to your GPU and/or graphics card circuit board(PCB).

The EK ﬁttings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

Do not use pure distilled water! For best results EK recommends

the use of EK-CyroFuel coolants!

- 3 -

TABLE OF CONTENT

PREPARING YOUR GRAPHICS CARD 4

INSTALLING THE WATER BLOCK 6

CHECKING FOR CONTACTS 8

INSTALLATION OF FITTINGS AND TUBING 8

INSERTING THE CARD IN YOUR PC CASE 9

REQUIRED TOOLS 9

SUPPORT AND SERVICE 10

SOCIAL MEDIA 10

- 4 -

PREPARING YOUR GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Remove all encircled screws using Phillips screwdriver. All heat

sink assembly screws should be removed, including self-adhesive

washers on both sides of the PCB (if present). Also remove encircled

screws on the IO bracket.

STEP 1

Remove all screws on

the IO bracket using

Phillips screwdriver

STEP 2

CLEANING THE PCB

Carefully detach the original stock cooler after removing all screws

securing in to the board. Wipe off the remains (by using non-

abrasive cloth or q-tip, as shown on sample photo) of the original

thermal compound until the components and circuit board are

completely clean. EKWB recommends the use of denatured alcohol

for removing TIM leftovers.

STEP 2

- 5 -

STEP 3

APPLYING THERMAL COMPOUND

Wipe off the remains(by using non-abrasive cloth or q-tip) of the

original thermal compound until the components and circuit board

are completely clean.

Apply thermal compound: lightly coat GPU chip with enclosed EK-

TIM Ectotherm thermal grease. EKWB recommends to apply thermal

grease in cross form for best performance (see sample photo).

STEP 4

CUTTING THERMAL PADS

Your block comes with thermal pad (F=1.0mm) which needs to be cut

to smaller chunck in order to cover all the VRM components such as

MOSFETs, IC memory and coils.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE

THERMAL PADS PRIOR TO INSTALLATION.

Replacement thermal pads:

1. Thermal PAD F 1.0mm - (120x16mm) - (EAN: 3830046996732)

STEP 5

PLACING THERMAL PADS ON PCB

Place thermal pads on the circuit board as shown in the picture below.

Refer to numbering in previous picture when applying thermal pads of

different sizes or thickeness. EK made sure to provide customers with

more than adequate quantity of thermal pads to complete this step.

STEP 3

Thermal pad F – 1.0 mm

120

STEP 4

STEP 5

- 6 -

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON TO THE GRAPHICS CARD

Carefully position the water block with preinstalled standoffs on to

the graphics card. During this process please make sure you align

mounting holes on the PCB with holes on the water block (same

applies for other tops). Also pay attention not to use too much

force by pressing the block down to the PCB. Chip dies are prone

to cracking.

STEP 1

M2.5 x 6 AX1

13 pcs

M 2.5 PVC washer

16 pcs

M2.5 x 4 AX1

16 pcs

M2.5 x 8 AX1

2 pcs

M3 x 4 DIN7985

2 pcs

Phillips-head

screwdriver

M 2.5 PVC washer

13 pcs

M 2.5 PVC washer

13 pcs

BAG CONTENT

Bag content is universal for all water blocks, you may not need all screws

M2.5 Helix nuts

6 pcs

M2.5 Helix nuts

2 pcs

- 7 -

STEP 2

ATTACHING THE BLOCK TO THE GRAPHIC CARD

Use a Phillips screwdriver screw with the enclosed M2.5x4 AX1

screws. EKWB recommends users to start tightening the screws

around the GPU core and continue outwards. Always use a plastic

washer under each and every screw! If the washer is already present

on the circuit board there is no need for additional washer.

STEP 2

M2.5 Helix nuts

M2.5x4 AX1 Screw

Plastic washer

M 2.5 PVC washer

13 pcs

M2.5 Helix nuts

2 pcs

M2.5 x 6 AX1

2 pcs

M2.5 x 4 AX1

11 pcs

M2.5x6 AX1

Screws

- 8 -

INSTALLATION OF FITTINGS AND TUBING

STEP 1

Screw in the two G1/4 threaded male ﬁttings. Attach the liquid

cooling tubes and connect the water-block(s) into the cooling circuit.

EKWB recommends using EK- ﬁttings.

You can use any opening as an inlet/outlet port. Do not forget to plug

the remaining two opening with enclosed EK-Plug G1/4 or equivalent.

CAUTION: In case of using connectors other than EK- series

compression ﬁttings, take special attention to the length of the

ﬁttings’ male G1/4” thread. 5mm is the maximum allowed G1/4”

thread length!

STEP 1

Tubing

EK- Plug G1/4

EK-Fitting

CHECKING FOR CONTACTS

If necessary temporarily remove the water block to check for uniform

surface contact between the block and the components, pay special

attention to the VRM section of the graphics card. Check whether

the water block makes contact with the intended integrated circuit.

Then repeat sub-steps in previous section to re-attach the block.

In case you fail to obtain good contact, please check again that

your thermal pad thickness or contact our support service at

http://www.ekwb.com/support.

- 9 -

INSERTING THE CARD IN YOUR PC CASE

Carefully lift your graphics card with installed block and insert it in

your PC’s motherboard PCI express expansion slot. Please bear in

mind that your graphics card is probably heavier than when it was

equipped with original heat sink fan assembly. One needs to be

very careful when handling the graphics card. Avoid all un-needed

manipulation of the VGA/water block assembly that might damage

your card or water block during ﬁnal installation.

Phillips-head screwdriver Scissors

REQUIRED TOOLS

For assistance please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Andere Handbücher für EK-FC GV100 PRO

Inhaltsverzeichnis

Andere ekwb Zubehör Handbücher

ekwb

ekwb EK-FC970 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-Velocity WS Series Bedienungsanleitung

ekwb

ekwb EK-FC 1070 GTX Ti ASUS Bedienungsanleitung

ekwb

ekwb EK-DCP 4.0 X-RES Leitfaden

ekwb

ekwb EK-FB KIT GA-X99 Handbuch

ekwb

ekwb EK-FC970 GTX TFX Backplate Leitfaden

ekwb

ekwb EK-Pro GPU WB RTX 6000 - Ni + Inox Bedienungsanleitung

ekwb

ekwb EK-Momentum AORUS Z390 MASTER Bedienungsanleitung

ekwb

ekwb EK-FB ASUS MAXIMUS III FORMULA Leitfaden

ekwb

ekwb EK-FB GA Z170X Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC Radeon Pro Duo Leitfaden

ekwb

ekwb EK-FB ASUS Maximus XI EXTREME Bedienungsanleitung

ekwb

ekwb EK-Momentum ROG Strix Z390I RGB Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX TF6 Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-Vector Strix RTX 2070 RGB Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-FB MSI X470 M7 RGB Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Maximus XI EXTREME Bedienungsanleitung

ekwb

ekwb EK-FB ASUS X399 GAMING RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB RTX A100 Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Z270I/Z370I Strix Monoblock Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ekwb EK-FC GV100 PRO Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken