Ekwb EK-Momentum AORUS Z390 MASTER Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on July 31th 2019

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

GENERAL INFORMATION Sample photo of AORUS Z390 MASTER motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 1: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are screws on

the back of the motherboard that need to be removed in order to remove the factory

installed MOSFET cooling solution. Additional screws need to be removed to remove

the plastic I/O cover.

CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be

trimmed in order to fit the voltage regulation area (MOSFETs and coils) on the

motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURE BELOW ARE

SCALED.

Installation manual for EK-Momentum AORUS Z390 MASTER water block

Cpu socket

Mosfets

Aorus Z390 Master

chipset heatsink

1. Thermal pad F –1.0mm

(EAN: 3830046996732)

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on July 31th 2019

PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads on PCB as

shown on the picture.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE

THERMAL PADS PRIOR TO INSTALLATION!

PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads on PCB as

shown on the picture.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE

THERMAL PADS PRIOR TO INSTALLATION!

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PLACING THE BLOCK ON TO THE MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat

spreader (IHS) with enclosed EK-TIM Ectotherm thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

Install three (3) M2.5 self adhesive PVC washers under marked standoffs as shown on

the picture below.

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-AORUS Z390

MASTER D-RGB Monoblock series water block gently to the motherboard. Make sure

that mounting holes are aligned.

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use three M2,5x5 AX1 screws. Tighten the screws evenly. Do not

use excessive force when tightening the screws!

B) CPU part: Use four M4x8 DIN7984 screws and washers.

Tighten the screws using enclosed 2.5mm allen key.

Use the enclosed screws and washers as shown on picture below:

Place the M2,5 self-adhesive PVC washers under marked standoffs!

M4x8 screws

Plastic washer

M2.5x5 Screws

Place 1mm thermal pads over

marked area and make sure all

mosfet chips and coils are

covered.

1.AORUS Z390 MASTER

2.AORUS Z390 ULTRA

Place 1mm thermal pads over marked area and

make sure all mosfet chips and coils are covered.

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on July 31th 2019

STEP 5: CONNECTING THE RGB LED STRIP (optional)

CONNECTING THE D-RGB LED (LED with 3 wires)

Plug the 4-pin connector from Monoblock D-RGB LED strip to the motherboard.

Please ensure that the arrow indicated on the connector is plugged into the +5V

line as indicated on your motherboard. Failure to do so will damage your

motherboard or LED strip.

For the EK- AORUS Z390 MASTER D-RGB Monoblock series water block to operate

properly the G1/4 port nearest to the right edge of the water block MUST BE USED

AS THE INLET PORT. EK recommends the use of EK- Fittings. When using fittings

other than EK- series please use hose clamps or appropriate substitute to secure the

tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is

always recommended for any liquid cooling system.

OPTION TO MOUNT WATER BLOCK WITH PLASTIC COVER:

If you want to install the plastic cover along with water block on the motherboard,

you need to bend or remove small piece of plastic, which is indicated in the photo.

REQUIRED TOOLS AND MOUNTING SCREWS:

Scissors Philips screwdriver Allen key

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Bend or remove marked

part from plastic cover!

Andere ekwb Zubehör Handbücher

ekwb

ekwb EK-FB ASUS Z 170S Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB ASRock X470 Taichi RGB Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Classy Backplate Leitfaden

ekwb

ekwb EK-FB ASUS Z270I/Z370I Strix Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB MSI X470 M7 RGB Bedienungsanleitung

ekwb

ekwb EK-FC7990 SE Leitfaden

ekwb

ekwb EK-FB ASRock X470 Gaming K4 RGB Bedienungsanleitung

ekwb

ekwb EK-XTOP Dual DDC 3.2 PWM Leitfaden

ekwb

ekwb EK-FC GV100 PRO Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB RTX A100 Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-FC980 GTX TF5 R2.0 Backplate Leitfaden

ekwb

ekwb EK-FB ASUS Maximus XI EXTREME Bedienungsanleitung

ekwb

ekwb EK-FB GA Z170X Monoblock Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX Ti Handbuch

ekwb

ekwb EK-Momentum ROG Strix Z390I RGB Bedienungsanleitung

ekwb

ekwb EK-FC 1070 GTX Ti ASUS Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX WF3 Backplate Leitfaden

ekwb

ekwb EK-SF3D Critical Point Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX TF6 Bedienungsanleitung

ekwb

ekwb EK-FB ASUS X99 Monoblock Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ekwb EK-Momentum AORUS Z390 MASTER Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken