Elation Waterfall 250 Bedienungsanleitung

User Manual

Software Version 1.60 Revised 10/2003

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 2

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 3

Table of Contents

Introduction........................................................................................................................... 5

Unpacking.................................................................................................................... 5

Customer Support...................................................................................................... 5

Discharge Lamp Precautions.................................................................................. 6

1Fixture Layout....................................................................................................................... 7

1.1 Safety Instructions ...................................................................................................... 7

2Preparation and Installation ............................................................................................. 9

2.1 Mounting.....................................................................................................................11

2.1.1 Clamps............................................................................................................11

2.1.2 Mounting Plate...............................................................................................12

2.2 Rigging the Power Spot ™......................................................................................12

2.3 Connections ..............................................................................................................13

2.3.1 Power Supply.................................................................................................13

2.3.2 DMX .................................................................................................................13

2.4 Fuse ............................................................................................................................13

3Menu Field ...........................................................................................................................15

3.1 Setting the DMX - Address (D001)..........................................................................18

3.2 Test Menu (TEST).......................................................................................................18

3.3 Lamp On/Off (LAMP).................................................................................................19

3.4 Reset (RESE)..............................................................................................................19

3.5 Running Time (lamp/unit) (TIME)............................................................................19

3.6 Invert Pan Movement (RPAN)..................................................................................20

3.7 Invert Tilt Movement (RTLT).......................................................................................20

3.8 DMX Mode ..................................................................................................................20

3.9 Special Functions (SPEC)........................................................................................21

3.9.1 Manual Drive (MANU)....................................................................................21

3.9.2 Lamp On (automatic) (LAAU)......................................................................22

3.9.3 Lamp Off (via DMX).......................................................................................22

3.9.4 DMX Input (DLOF)..........................................................................................22

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 4

3.9.5 LED Display (DISP)......................................................................................23

3.9.6 Fixture Temperature (TEMP).........................................................................23

3.9.7 Fan Control (FANS)......................................................................................24

3.9.8 Adjustments and Calibrations (ADJU).....................................................24

3.9.9 Default Settings (DFSE)................................................................................25

3.9.10Feedback (FEED)...........................................................................................25

3.9.11Fault Corrections (EFLD).............................................................................26

3.10 Error and Information Messages...........................................................................26

4DMX Channel Selection (DMX Protocol)........................................................................27

5Lamp Change .....................................................................................................................33

5.1 Safety Regulations ...................................................................................................33

5.2 Realize the Lamp Change......................................................................................33

5.3 Lamp Adjustment .....................................................................................................34

6Change a Gobo...................................................................................................................37

6.1.1 Safety Regulations........................................................................................37

6.1.2 Realize the Gobo Change..........................................................................37

7Maintenance and Cleaning the Power Spot 250™....................................................39

7.1 Safety Regulations ...................................................................................................39

7.2 Circumference and Interval.....................................................................................39

7.3 Cleaning the Optical System..................................................................................40

8Technical Specification ...................................................................................................32

9Warranty..............................................................................................................................33

10 Index.....................................................................................................................................35

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 5

INTRODUCTION: Congratulations, you have just purchased one of the most innovative

and reliable lighting fixtures on the market today! The Power Spot 250™, has been

designed to perform reliably for years when the guidelines in this booklet are followed.

Please read and understand the instructions in this manual carefully and thoroughly before

attempting to operate this unit. These instructions contain important information regarding

safety during use and maintenance.

UNPACKING: Thank you for purchasing the Power Spot 250™ by Elation Professional®.

Every Power Spot 250™ has been thoroughly tested and has been shipped in perfect

operating condition. Carefully check the shipping carton for damage that may have occurred

during shipping. If the carton appears to be damaged, carefully inspect your unit for

damage and be sure all accessories necessary to operate the unit have arrived intact. In

the event damage has been found or parts are missing, please contact our customer

support team for further instructions. Please do not return this unit to your dealer without

first contacting customer support at the number listed below.

CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to

provide set up help and to answer any question should you encounter problems during

your set up or initial operation. You may also visit us on the web at www.elationlighting.com

for any comments or suggestions. For service related issue please contact Elation

Professional®. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific

Standard Time.

Voice: (323) 582-3322

Fax: (323) 582-3108

E-mail: [email protected]

Forum: www.ElationLighting.com/forum/

Warning!To prevent or reduce the risk of electrical shock or fire, do not expose this unit to

rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself, doing so will void your manufactures warranty.

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

WARRANTY REGISTRATION:The Power Spot 250™ carries a two year (730 days) limited

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 6

warranty. Please fill out the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid and accompany a

return authorization (R.A.) number. The R.A. number must be clearly written on the outside

of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper and included in the shipping container. If the unit

is under warranty, you must provide a copy of your proof of purchase invoice. Items

returned without a R.A. number clearly marked on the outside of the package will be refused

and returned at cutomers exspence. You may obtain a R.A. number by contacting customer

support at (323) 582-3322, extension 170.

DISCHARGE LAMP WARNING:This fixture is fitted with a discharge

lamp, which is highly susceptible to damage if improperly handled.

Never touch the lamp with your bare hands, as the oil from your hands

will shorten lamp life. Also, never move the fixture until the lamps have

had ample time to cool. Remember, lamps are not covered under

warranty conditions.

This fixture emits intense UV radiation, which is harmful to the eyes and skin. The intense

luminance of the lamp can cause severe damage to the retina. Never operate this fixture

withtheprotectivecoversremoved,thes e covers have been specially designed to shield

against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the

lamp at all times.

Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce lamp

life and intensity.

To achieve the intensity associated with discharge lamps, these lamps use a gas sealed

in a high-pressure environment to emit a brilliant output. Due to the high pressure involved

with the construction of the lamp, the lamp may explode during prolonged extensive use.

This risk is increased with age; added care is encouraged when dealing with older lamps.

Thus, lamp should always be replaced at the end of their recommended duty cycle.

Extreme caution should be used when operated this or any fixture fitted with a gas

discharge lamp.

Never open this fixture while in use!

During the initial operation of this fixture, a light smoke or smell may emit from the interior

of the fixture. This is a normal process and is caused by excess paint in the interior of the

casing burning off from the heat associated with the lamp.

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 7

Safety Instructions

The Power SPOT 250™ is an extremely sophisticated piece of

electronic equipment. To guarantee a smooth operation, it is

important to follow the guidelines in this manual. The

manufacturer of this device will not accept responsibility for

damages resulting from the misuse of this fixture due to the

disregard of the information printed in this manual.

1. Always be sure that the fan and the air inlets remain clean and are never blocked.

Allow about 6” (15cm) between this fixture and other devices or a wall to allow for

proper cooling.

2. Never touch the fixture during normal operation. This can cause severe personal

injuries and/or damage to the fixture.

3. Be sure to unplug the POWER SPOT 250™ from the power outlet before

performing any service related issues.

4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power

before you open the POWER SPOT 250™. To prevent personal injury, never touch

the lamp if you are not absolutely sure it has cooled.

5. Never look directly into the lamp beam. You risk injury to your retina, which may

induce blindness.

6. Be sure to track and record the lamp running time. The lamp should be changed

at the end of the specified lamp life, regardless of lamp output. You may also have

to change the lamp if it shows any deformations or damage. The same is with all

glass components, color filters, lenses and mirrors.

7. For safe operation, follow the Installation guide described in chapter two of this

manual. Operating the POWER SPOT 250™ without suited safety aids such as

safety cables or clamps can increase the risk of damage and/or personal injury.

8. Installation should only be performed by qualified and certified personal.

9. When mounting this fixture, use only the original rigging parts included with this

fixture. Any structural modification will void the original manufactures warranty and

may increase the risk of damage and/or personal injury.

10. To reduce the risk of fire or shock, do not expose this unit to rain or moisture.

11. Do not attempt to operate this fixture if the power cord is frayed or damaged.

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 8

1. Fixture Layout

1. Lens Assembly

2. Arm

3. Base

4. Carrying Handles

5. Up Button

6. Down Button

7. Enter Button

8. Mode Button

9. LED Display

10. Firmware Connection

11. Microphone Sensitivity

12. DMX Input Jack

13. DMX Output Jack

14. Power On/Off Switch

15. Fuse Housing

16. Cooling Fan (air inlet)

MaxMin

DMX IN DMX OUT

Software Update

1 . Groun d

2.Data-

3.Data+

POWER

210V~

230V~

250V~

50Hz

60Hz

Power input

FUSE:

T3.15A @250V

LAMP:

MSD 250W

Serial

n um ber:

Fuse

Mic Sensitive

PUSH

FUSE

MODE ENTER UPDOWN

MODEEN T E RUP DOWN

87 65

12 13 14

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 9

1. Lens Assembly - This high quality lens is a fully focusing. Focus the lens by

manually turning the lens in a clockwise or counter-clockwise direction until the

desired effect is achieved.

2. Retaining Arm – This Arm serves as a conduit for all electronic from the base to

the lens assembly.

3. Base – The fixture base holds all main electronic for the fixture and provides a

means to secure the fixture to wall or ceiling.

4. Carrying Handles - The includes built-in carrying handles. Be sure to always

handle the fixture by the built-in handles. Never lift or carrying the fixture by head or

yoke. Pulling on or transporting the fixture by moving head may severely damage

the fixture and will void the fixture warranty.

5. Up Button - This button is used to scroll forward when navigating through the

system menu.

6. Down Button - This button is used to scroll backwards when navigating through

the system menu.

7. Enter Button - This button is used to select and confirm a function when working in

the system menu.

8. Mode Button – This button is used to access the fixture’s main system menu and

programming functions.

9. LED Display – This display is detail the menu and operating functions.

10.Firmware Connection – This connection is designed to be used solely by a

qualified technician to upgrade and test the fixture.

11.Microphone - This microphone receives external low frequencies to trigger the

fixture in Sound-Active and Master/Slave mode.

Power Spot 250™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 10

12.DMX Input Jack – This jack is used to receive an incoming DMX signal or

Master/Slave signal.

13.DMX Output Jack – This jack is used to transmit the incoming DMX signal to

another DMX fixture, or transmit a Master/Slave signal to the next Power Wash

250™ in the chain. For best results in DMX or Master/Slave mode terminate this

jack if it is the last fixture in the chain. See “Terminator” on page 14.

14.Power Switch – This switch is used to control main power to the fixture.

15.Fuse Holder – This housing stores a 6.3 amp (3.15 amp 220v) GMA protective

fuse. Never defeat the fuse, the fuse is designed to protect the electronics in the

event of sever power fluctuations. Always be sure to replace the fuse with an exact

match as to the one being replaced, unless otherwise told to do so by an

authorized Elation®service technician.

16.Cooling Fan - This fixture is equipped with a high velocity variable fan to aid in the

cooling process. This fan is designed to vary its’ velocity at different operating

temperatures, to provide better cooling when the fixture reached higher operating

temperatures associated with long usage. Be sure to never obstruct the cooling

fan during normal usage. Also, be sure to keep this vent clean at all times. A

blocked or malfunctioning cooling system may shorten lamp life and fixture

reliability.

Andere Handbücher für Waterfall 250

Inhaltsverzeichnis

Andere Elation Scheinwerfer Handbücher

Elation

Elation RAYZOR BEAM 2R Bedienungsanleitung

Elation

Elation E Spot Led Bedienungsanleitung

Elation

Elation Design LED 36MH Bedienungsanleitung

Elation

Elation WW PROFILE Bedienungsanleitung

Elation

Elation ELED DW PAR56 Bedienungsanleitung

Elation

Elation TVL2000 II Bedienungsanleitung

Elation

Elation DW CHORUS 24 Bedienungsanleitung

Elation

Elation VISION 250 Bedienungsanleitung

Elation

Elation ELAR EXFLOOD Bedienungsanleitung

Elation

Elation DESIGN SPOT 575E Bedienungsanleitung

Elation

Elation Arena Par CW Bedienungsanleitung

Elation

Elation ELARQUADBAR Bedienungsanleitung

Elation

Elation KLF832 Bedienungsanleitung

Elation

Elation DESIGN SPOT 575E Bedienungsanleitung

Elation

Elation ProTron LED Bedienungsanleitung

Elation

Elation Design LED 108IP Bedienungsanleitung

Elation

Elation Design LED 108IP Bedienungsanleitung

Elation

Elation ACL PAR 200 Bedienungsanleitung

Elation

Elation VOLT Q5E SIX PACK Bedienungsanleitung

Elation

Elation PROTEUS LUCIUS PRL546 Bedienungsanleitung

Elation

Elation Waterfall 250 Bedienungsanleitung

Elation

Elation Waterfall 250 Bedienungsanleitung

Elation

Elation KL FRESNEL 4 Bedienungsanleitung

Elation

Elation VISION 250 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung