Elcometer 456 Bedienungsanleitung
English
Elcometer 456
Duct Deposit Measuring System
Operating Instructions
456_ductkit_TMA_0436_00_03_ A6.fm Page -1 Wednesday, October 21, 2009 12:27 PM
English
R
This product meets the Radio and Telecommunications Terminal Equipment Directive.
Bluetooth SIG QDID = B014393.
is a registered trademark of Elcometer Limited.
®and Bluetooth®are trademarks owned by Bluetooth SIG Inc and licensed to Elcometer Limited.
ElcoMaster®is a registered trademark of Elcometer Limited.
All other trademarks acknowledged.
© Copyright Elcometer Limited. 2009.
All rights reserved. No part of this Document may be reproduced, transmitted, transcribed, stored (in a retrieval system
or otherwise) or translated into any language, in any form or by any means (electronic, mechanical, magnetic, optical,
manual or otherwise) without the prior written permission of Elcometer Limited.
A copy of this Instruction Manual is available for download on our Website via www.elcometer.com.
Doc.No. TMA-0436 Issue 03
Text with Cover No: 20382
456_ductkit_TMA_0436_00_03_ A6.fm Page 0 Wednesday, October 21, 2009 12:27 PM
R
1
CONTENTS
Section Page
1 About this equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Getting started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Taking a reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Using the duct cleaning template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Calibrating your gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6 Printing readings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7 Transferring readings to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8 Producing reports using ElcoMaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9 Probe technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
10 Spares and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
11 Related equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
456_ductkit_TMA_0436_00_03_ A6.fm Page 1 Wednesday, October 21, 2009 12:27 PM
R
2
Thank you for your purchase of this Elcometer 456 Duct Deposit Measuring System. Welcome to
Elcometer.
Elcometer are world leaders in the design, manufacture and supply of coatings inspection equipment. Our
products cover all aspects of coating inspection, from development through application to post application
inspection.
The Elcometer 456 Duct Deposit Measuring System is a world beating product. With the purchase of this
product you now have access to the worldwide service and support network of Elcometer. For more
information visit our website at www.elcometer.com.
1 ABOUT THIS EQUIPMENT
The Elcometer 456 Duct Deposit Measuring System is designed for measurement of the thickness of dust
and grease deposits within ventilation systems and kitchen ducts made of ferrous metals.
Use the template supplied to help you take readings of deposit thickness over the test area and then save
your measurements in the gauge memory. When you have finished testing, download your measurements
to a PC via Bluetooth
®
or cable and then produce a professional survey report using the pre-designed
reports in ElcoMaster software. This is the DTT (Deposit Thickness Test) in HVCA guide TR/19.
To maximise the benefits of your new Elcometer 456 Duct Deposit Measuring System, please take
some time to read these Operating Instructions and the separate instruction manual for the
Elcometer 456 gauge. Do not hesitate to contact Elcometer or your Elcometer supplier if you have
any questions.
456_ductkit_TMA_0436_00_03_ A6.fm Page 2 Wednesday, October 21, 2009 12:27 PM
R
3
1.1 CHECKING THE CONTENTS OF THE BOX
• Elcometer 456 Coating Thickness Gauge - Top model
• T456F1D Duct Probe
• Probe calibration foils (x3) and ferrous zero plate
• Duct Cleaning Template
• ElcoMaster™ Software, including Duct Deposit Report template
• Batteries, x2
• Wrist Harness
• Black Plastic Carry Case
• Operating Instructions
1.2 PACKAGING
The equipment is packed in cardboard and plastic packaging. Please ensure that this packaging is disposed
of in an environmentally sensitive manner. Consult your Local Environmental Authority for further guidance.
456_ductkit_TMA_0436_00_03_ A6.fm Page 3 Wednesday, October 21, 2009 12:27 PM
R
4
2 GETTING STARTED
Before you use your gauge for the first time, remove the paper strip from the battery compartment.
2.1 FIT PROBE
Align probe connector keyway with the socket on the base of the gauge and push in
direction illustrated. The connector locks automatically.
2.2 SWITCH ON GAUGE
Switch on - press .
Switch off - press and hold .
2.3 INTERFACING WITH A PC
Your gauge has a Bluetooth
®
interface. Connect your gauge to your PC using Bluetooth
®
for quick and easy data transfer and welcome screen download - see “Transferring
readings to a computer” on page 11.
If your PC does not have a Bluetooth
®
interface, use a Bluetooth
®
to USB convertor (see
“Spares and accessories” on page 16) or connect your gauge using the serial interface
located on the side of your gauge. Connect your gauge to the PC using the optional PC
connection cable.
456_ductkit_TMA_0436_00_03_ A6.fm Page 4 Wednesday, October 21, 2009 12:27 PM
R
5
3 TAKING A READING
3.1 BEFORE YOU START
Have you calibrated the gauge?........see page 8 of these instructions.
Do you require statistics?..................press STATS.
Do you want to save readings?.........press DATA.
Have you selected units (µm, etc)?...press MENU>SETUP>UNITS.
3.2 PROCEDURE
1. Switch on the gauge.
2. Hold the probe and press firmly against the surface you are
measuring. The reading may be inaccurate if the probe is not
held flat against the surface.
3. Read the depth shown on the display.
456_ductkit_TMA_0436_00_03_ A6.fm Page 5 Wednesday, October 21, 2009 12:27 PM
R
6
4 USING THE DUCT CLEANING TEMPLATE
Take readings (see page 5) in accordance with the appropriate HVCA
a
method of measurement.
Use the Duct Cleaning Template supplied and the procedure described below to help you take a group of
20 readings before and after cleaning in the test location. Then output your readings to ElcoMaster™.
1. Place the Duct Cleaning Template
in the duct.
2. Mark the position of each corner.
3. Use your gauge to take a reading in
each of the holes in the template
and save all these readings in a
batch.
4. Remove the template and clean
the surface of the duct within the
boundaries of the corner marks.
a. Heating and Ventilating Contractors’ Association, Guide to Good Practice TR/19, Cleanliness of Ventilation Systems
(www.hvca.org.uk).
(1) (2)
(3) (4)
456_ductkit_TMA_0436_00_03_ A6.fm Page 6 Wednesday, October 21, 2009 12:27 PM
R
7
5. Replace the Duct Cleaning
Template in the duct ensuring that it
is in the same position as before -
use the corner marks as
positioning guides.
6. Use your gauge to take a second
set of readings in the same order
as the first set and save your
readings in the same batch.
7. Connect your gauge to a PC and
use the Duct Deposit Report
template in ElcoMaster™ to
produce a professional report of
your readings - see “Producing
reports using ElcoMaster” on page 12.
(5) (6)
456_ductkit_TMA_0436_00_03_ A6.fm Page 7 Wednesday, October 21, 2009 12:27 PM
R
8
5 CALIBRATING YOUR GAUGE
Before taking measurements, always calibrate your gauge.
Follow steps 1 to 9 below to calibrate your gauge. Complete instructions on how to calibrate your gauge are
provided in the separate instruction book supplied with the gauge.
(1) Place the plastic shims on the
ferrous zero plate supplied with
your gauge. If necessary, the
shims should be stacked upon
each other until the thickness
totals approximately 250 µm.
(2) Switch on the gauge, hold the
probe well away from any metal
and press CAL.
(3) Place probe on shim stack.
Take a number of readings (to
obtain the average thickness of
the stacked shims).
456_ductkit_TMA_0436_00_03_ A6.fm Page 8 Wednesday, October 21, 2009 12:27 PM
Andere Handbücher für 456
13
Inhaltsverzeichnis
Andere Elcometer Messgerät Handbücher
Elcometer
Elcometer 112 Bedienungsanleitung
Elcometer
Elcometer 500 Bedienungsanleitung
Elcometer
Elcometer Protovale 331 Bedienungsanleitung
Elcometer
Elcometer 331 H Bedienungsanleitung
Elcometer
Elcometer Zahn 2210 Bedienungsanleitung
Elcometer
Elcometer protovale P330 Bedienungsanleitung
Elcometer
Elcometer 119 Bedienungsanleitung
Elcometer
Elcometer MTG2 Bedienungsanleitung
Elcometer
Elcometer 415 Bedienungsanleitung
Elcometer
Elcometer 139 Bedienungsanleitung
Elcometer
Elcometer 456 Model E Bedienungsanleitung
Elcometer
Elcometer 456 Bedienungsanleitung
Elcometer
Elcometer E224C-BI Bedienungsanleitung
Elcometer
Elcometer 138/2 Bedienungsanleitung
Elcometer
Elcometer 456 Ultra Bedienungsanleitung
Elcometer
Elcometer 407L Bedienungsanleitung
Elcometer
Elcometer 456 Bedienungsanleitung
Elcometer
Elcometer Adhesion Verification Unit Bedienungsanleitung
Elcometer
Elcometer 138 Bedienungsanleitung
Elcometer
Elcometer Novo-Gloss 401 Bedienungsanleitung
