Emerson Dixell XRi30T Bedienungsanleitung

1569005020 XRi30-31T QRG EN v1.2 2020.08.26 XRi30T - XRi31T 1/2

FULL TOUCH –XRi30T AND XRi31T

Please put this label near the controller in order to keep

all information you need at your fingertips!

CONTACT: dixell.service@emerson.com

SAFETY INFO

•This manual is part of the product and should be kept near the instrument for easy and quick reference.

•The instrument shall not be used for purposes different from those described hereunder. It cannot be used as a safety device.

•Dixell Srl reserves the right to change the composition of its products, even without notice, ensuring the same and unchanged functionality.

•In case of failure or faulty operation contact the local distributor or “Dixell S.r.l.” with a detailed description of the fault.

•The instrument must not be opened.

•Check the application limits and the correct power supply voltage before proceeding.

•Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high

atmospheric humidity to avoid condensation

•Warning: disconnect the power supply and all other electrical connections before any kind of maintenance.

•Observe the maximum current value which can be applied to each relay (see Technical Data).

•Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without crossing or intertwining.

USER INTERFACE

SCREEN

APPEARANCE

SCREEN

APPEARANCE

Home

Info

Virtual

Keyboard

Programming

Mode

Parameter

Set Point Menu

SCREEN NAME

DESCRIPTION

Home

This screen shows temperature value, measurement unit and active alarms only. This is the first screen after power

on or after exit from other status.

Virtual Keyboard

This screen shows available functions. Activated function will blink when this screen is visualized.

Info

This screen shows activated functions and regulation outputs (compressor, ventilators)

Programming Mode

This screen enables the modification of Set point or parameters.

Parameter Menu

These screens enable the modification of all parameter values.

Set Point Menu

This screen enables the modification of the Set Point value.

USER INTERACTION

HOME NAVIGATION

PROG MENU ACTIVATION

SET POINT MODIFICATION

PROG MENU NAVIGATION

GESTURE

HOW-TO

DESCRIPTION

ONE TAP

Press a specific area of the

surface with a finger for 1 sec

Switch ON / Switch OFF: when in Virtual Keyboard, use this to turn on/off a specific

function. When into programming mode, use this to select a parameter or a

parameter value.

TAP and

HOLD

Press anyplace of the surface with

a finger for 3 sec

Enter / Save: use this to enter programming mode or parameter menu and to save

modifications. When in Virtual Keyboard, use this on the “ONOFF” to switch OFF

and ON the device.

H-SWIPE

Drag a finger across surface, from

left to right or from right to left

Browse: use horizontal swipe (right to left or left to right) to browse through HOME,

Virtual Keyboard and Info View. When in Programming menu: use horizontal swipe

to browse through parameter menu.

V-SWIPE

Drag a finger across surface, from

top to bottom or from bottom to top

(overlapping only one of the digits)

Modify: use vertical swipe (from top to bottom or bottom to top) to change a

parameter value.

H-SWIPE

TAP and HOLD

TAP and HOLD on SET

TAP and HOLD on PRG

H-SWIPE

1569005020 XRi30-31T QRG EN v1.2 2020.08.26 XRi30T - XRi31T 2/2

H-SWIPE

to browse

PROGRAMMING MENU

(…)

and icons are blinking

TECHNICAL SPECIFICATIONS

FEATURES

DESCRIPTION

Housing

Self-extinguishing PC

Dimensions

Front fascia 38x80 mm; case depth 81mm

Mounting device

Panel, 71x29mm panel cut-out

Degree of Protection

NEMA –UL 50e

Indoor use only, type 1 enclosure

IP-IEC/EN 60529

Front panel: IP66

Rear Housing: IP00

Power Supply

230Vac 10%, 50/60Hz; 110Vac 10%, 50/60Hz; 100 to 240VAC10%, 50/60Hz

Overvoltage Category

Rated Power

12VAC: 3VA; 110VAC: 4VA; 230VAC: 4VA; 100-240VAC: 3VA

FEATURES

DESCRIPTION

Rated Impulse Voltage

2500V

Display

White display, LED type, 3 digits with decimal point and multi-function icons

Buzzer

Internal, always present

Software Class

Terminal blocks / Terminal

Connections

Plug-in or screw terminal block, wire section between 0,5 and 2,5 mm2

Max tightening force: 0.3 N/m for 3,5mm pitch, 0.4 N/m for 5,0mm pitch

Data Storing

Real Time Clock: Data maintenance up to 6 months with lithium battery. Other parameters: internal flash.

Type of Action

1.B

Pollution Degree

2, non-condensing humidity

Ambient Operating

Temperature and Humidity

IEC/EN

0T60°C; 20-85 rH% (non-condensing humidity)

UL-CAN/CSA

-20T60°C; 20-85 rH% (non-condensing humidity)

Shipping and storage

temperature

-40T85°C; 20-85 rH% (non-condensing humidity)

Resistance to Heat

UL 94 V-0

Measurement range

NTC: -40T110°C, resolution 0.1°C or 1°C (selectable); PT1000: -100T150°C, resolution 0.1°C or 1°C

(selectable); PTC: -50T150°C, resolution 0.1°C or 1°C (selectable)

Accuracy

±1% compared to the full scale

Inputs

Up to 4 NTC, PTC or PT1000 (configurable); Up to 2 voltage free contacts

Relay Outputs

Nominal

IEC

oA1

SPST 16A,

250VAC

10FLA, 60LRA, 30k cycles

12A resistive, 230Vac, 50k cycles

Pilot Duty B300, 6k cycles

10(4)A, 240 Vac, 50-60 Hz,

100K cycles

oA2

SPDT 8A,

250VAC

½ hp, 230 Vac, 30k cycles

10A resistive, 230Vac, 30k cycles

Pilot Duty B300, 30k cycles

8(3)A, 240 Vac, 50-60 Hz,

50K cycles

Maximum ampacity on common

terminal of oA1 and oA2

16 A

Analogue Outputs

1Ao

Frequency output; Supply max voltage=12Vdc; Max supply

current=2mA; duty cycle 50%; 0 to 166 Hz

A3: Freq

A4: GND

2Ao (*)

0-10Vdc; Max supply current=5mA

A1: V+

A2: GND

I/O port

HOT-KEY: MAX voltage allowed is 5 VDC. DO NOT CONNECT ANY EXTERNAL POWER SUPPLY.

XH-REP: remote display support available only for specific models. XH-REP must be connected to the

HOTKEY port. When in use, all the other functions are disabled (no Pb4, no d.i.2, no TTL available).

Purpose of control

Operating control

Construction of control

Incorporated control, intended to be used in Class I or Class II equipment

Approvals

R290/R600a: relays tested according to IEC EN60079:0 and IEC EN60079:15

IEC 60730-1; IEC 60730-2-9

UL 60730-1; UL 60730-2-9

CAN/CSA-E60730-1; CAN/CSA-E60730-2-9

(*) Available only for XRi31T

TAP and HOLD

PRESS “PRG”

TAP and HOLD “PRG”

TAP and HOLD “PRG” to

save and exit

and exit

V-SWIPE

to modify

TAP and HOLD “PRG”

Andere Handbücher für Dixell XRi30T

Dieses Handbuch passt für folgende Modelle

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount MLT 2 Kurzanleitung

Emerson

Emerson Rosemount 285 Bedienungsanleitung

Emerson

Emerson Rosemount TCL Bedienungsanleitung

Emerson

Emerson MRLDS-250 Betriebsanleitung

Emerson

Emerson Micro Motion G-Series Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Technisches Datenblatt

Emerson

Emerson Rosemount 9195 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Series Bedienungsanleitung

Emerson

Emerson Fisher 4320 Konfigurationshandbuch

Emerson

Emerson Rosemount 1057 Bedienungsanleitung

Emerson

Emerson Rosemount 1057 Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Emerson

Emerson Micro Motion MVD Direct Connect Bedienungsanleitung

Emerson

Emerson Rosemount 3814 Programmierhandbuch

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson Rosemount Analytical 1054B C Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Lumity IC100D EVO Bedienungsanleitung

Emerson

Emerson 250-5000 Bedienungsanleitung

Emerson

Emerson Daniel Ultrasonic 100 Series Bedienungs- und Wartungshandbuch

Emerson

Emerson Rosemount 9295 Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Benutzerhandbuch

Emerson

Emerson MRLDS-250 Bedienungsanleitung

Emerson

Emerson CSI 2140 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung