Emerson Rosemount 8600D Series Bedienungsanleitung

Quick Start Guide

00825-0100-4860, Rev EB

April 2018

Rosemount® 8600 Series Vortex

Flowmeter

1 About this guide

This guide provides basic guidelines for the Rosemount™ 8600D Series

Vortex Flowmeter. It does not provide instructions for detailed configuration,

diagnostics, maintenance, service, troubleshooting, Explosion-proof,

Flameproof, or Intrinsically Safe (I.S.) installations. Refer to the reference

manual for more instruction. The manuals and this quick start guide are also

available electronically on EmersonProcess.com/Rosemount.

WARNING!

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in

accordance with the appropriate local, national, and international standards,

codes, and practices. Review the approvals section of thereference manual

for any restrictions associated with a safe installation.

•Before connecting a handheld communicator in an explosive

atmosphere, make sure the instruments in the loop are installed in

accordance with intrinsically safe or non-incendive field wiring practices.

•Verify the operating atmosphere of the flowmeter is consistent with the

appropriate product certifications.

•In an Explosion-proof/Flameproof installation, do not remove the

flowmeter covers when power is applied to the unit. Electrical shock can

result in death or serious injury.

WARNING!

Electrical shock can result in death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

1.1 Return policy

Emerson procedures must be followed when returning equipment. These

procedures ensure legal compliance with government transportation

agencies and help provide a safe working environment for Emerson

employees. Failure to follow Emerson procedures will result in your

equipment being refused delivery.

Quick Start Guide April 2018

2Rosemount 8600 Series Vortex Flowmeter

1.2 Emerson Flow customer service

Email:

•Worldwide: [email protected]

•Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800 522 6277 U.K. 0870 240 1978 Australia 800 158 727

Canada +1 303 527

5200

The Nether-

lands

+31 (0) 704 136

666

New Zealand 099 128 804

Mexico +41 (0) 41 7686

111

France 0800 917 901 India 800 440 1468

Argentina +54 11 4837

7000

Germany 0800 182 5347 Pakistan 888 550 2682

Brazil +55 15 3413

8000

Italy 8008 77334 China +86 21 2892

9000

Venezuela +58 26 1731

3446

Central & East-

ern

+41 (0) 41 7686

111

Japan +81 3 5769

6803

Russia/CIS +7 495 981

9811

South Korea +82 2 3438

4600

Egypt 0800 000 0015 Singapore +65 6 777 8211

Oman 800 70101 Thailand 001 800 441

6426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 0444 0684

April 2018 Quick Start Guide

Quick Start Guide 3

2 Installation

2.1 Mount the flowmeter

Design process piping so the meter body will remain full, with no entrapped

air. The vortex flowmeter can be installed in any orientation without affecting

accuracy. However, the following are guidelines for certain installations.

2.1.1 Vertical mounting

If the vortex flowmeter will be installed in a vertical orientation:

•Install upward or downward flow for gas or steam.

•Install upward flow for liquids.

Vertical installationFigure 2-1:

A. Gas flow

B. Liquid or gas flow

Quick Start Guide April 2018

4Rosemount 8600 Series Vortex Flowmeter

2.1.2 Horizontal mounting

Horizontal installationFigure 2-2:

A. Preferred installation—meter body installed with electronics to side of pipe

B. Acceptable installation—meter body installed with electronics above pipe

For steam and fluids with small solids content, it is recommended to have the

flowmeter installed with the electronics to the side of the pipe. This will

minimize potential measurement errors by allowing the condensate or solids

to flow under the shedder bar without interrupting the vortex shedding.

2.1.3 High temperature mounting

The maximum temperature for integral electronics is dependent on the

ambient temperature where the flowmeter is installed. The electronics must

not exceed 185 °F (85 °C).

Figure 2-3 shows combinations of ambient and process temperatures needed

to maintain a housing temperature of less than 185 °F (85 °C).

April 2018 Quick Start Guide

Quick Start Guide 5

Ambient/Process temperature limitsFigure 2-3:

A. Ambient temperature °F (°C)

B. Process temperature °F (°C)

C. 185 °F (85 °C) Housing temperature limit.

Note

The indicated limits are for horizontal pipe and vertical meter position, with meter

and pipe insulated with 3 in. (77 mm) of ceramic fiber insulation.

The following orientations are recommended for applications with high

process temperatures.

•Install with electronics head beside or below process pipe.

•Insulation around pipe may be necessary to maintain ambient

temperature below 185 °F (85 °C).

Note

Insulate pipe and meter body only. Do not insulate support tube bracket or

transmitter so heat can be dissipated.

2.1.4 Steam installations

Avoid installation shown in Figure 2-4. Such conditions may cause a water-

hammer condition at start-up due to trapped condensation.

Quick Start Guide April 2018

6Rosemount 8600 Series Vortex Flowmeter

Improper installationFigure 2-4:

2.1.5 Upstream/downstream requirements

The flowmeter may be installed with a minimum of ten straight pipe

diameters (D) upstream and five straight pipe diameters (D) downstream by

following the K-factor corrections as described in the 8800 Installation Effects

Technical Data Sheet (00816-0100-3250). No K-factor correction is required

if 35 straight pipe diameters upstream (35D) and 10 straight pipe diameters

downstream (10D) are present.

2.1.6 External pressure/temperature transmitters

When using pressure and temperature transmitters in conjunction with the

flowmeter for compensated mass flows, install the transmitters downstream

of the flowmeter as shown in Figure 2-5.

Upstream/Downstream pipingFigure 2-5:

A. Pressure transmitter

B. Four straight pipe diameters downstream

C. Temperature transmitter

D. Six straight pipe diameters downstream

April 2018 Quick Start Guide

Quick Start Guide 7

2.1.7 Flanged style installation

Flanged style installationFigure 2-6:

A. Installation bolts and nuts (supplied by customer)

B. Gaskets (supplied by customer)

C. Flow direction

Note

The required bolt load for sealing the gasket joint is affected by several factors,

including operating pressure, gasket material, width, and condition. A number of

factors also affect the actual bolt load resulting from a measured torque,

including condition of bolt threads, friction between the nut head and the flange,

and parallelism of the flanges. Due to these application-dependent factors, the

required torque for each application may be different. Follow the guidelines

outlined in ASME PCC-1 for proper bolt tightening. Make sure the flowmeter is

centered between flanges of the same nominal size as the flowmeter.

2.2 Install remote electronics

If you order one of the remote electronics options (options R10, R20, R30, or

RXX), the flowmeter assembly ships in two parts:

1. The meter body with an adapter installed in the support tube and an

interconnecting coaxial cable attached to it.

2. The electronics housing installed on a mounting bracket.

Refer to Figure 2-7 and these steps to connect the loose end of the coaxial

cable to the electronics housing.

Quick Start Guide April 2018

8Rosemount 8600 Series Vortex Flowmeter

Remote electronics installationFigure 2-7:

A. Meter body

B. Support tube

C. Sensor cable nut

D. Nut

E. Washer

F. Union

G. Meter adapter

H. Coaxial cable

I. 1/2 in. NPT conduit atapter or cable gland (supplied by customer)

J. Electronics housing

K. Ground connection

L. Housing base screw

M. Housing adapter

N. Housing adapter screws

O. 1/2 in. NPT conduit adapter or cable gland (supplied by customer)

P. Coaxial cable nut

Prerequisites

1. Mount the meter body in the process flow line as described in Section 2.1.

2. Mount the bracket and electronics housing in the desired location. The

housing can be repositioned on the bracket to facilitate field wiring and

conduit routing.

April 2018 Quick Start Guide

Quick Start Guide 9

Procedure

1. If you plan to run the coaxial cable in conduit, carefully cut the conduit to

the desired length to provide for proper assembly at the housing. A

junction box may be placed in the conduit run to provide a space for extra

coaxial cable length.

CAUTION!

The coaxial remote cable cannot be field terminated or cut to length. Coil

any extra coaxial cable with no less than a 2-in. (51 mm) radius.

2. Slide the conduit adapter or cable gland over the loose end of the coaxial

cable and fasten it to the adapter on the meter body support tube.

3. If using conduit, route the coaxial cable through the conduit.

4. Place a conduit adapter or cable gland over the end of the coaxial cable.

5. Remove the housing adapter from the electronics housing.

6. Slide the housing adapter over the coaxial cable.

7. Remove one of the four housing base screws.

8. Attach and securely tighten the coaxial cable nut to the connection on

the electronics housing.

9. Attach the coaxial cable ground wire to the housing via the housing base

ground screw.

10. Align the housing adapter with the housing and attach with two screws.

11. Tighten the conduit adapter or cable gland to the housing adapter.

CAUTION!

To prevent moisture from entering the coaxial cable connections, install

the interconnecting coaxial cable in a single dedicated conduit run or use

sealed cable glands at both ends of the cable.

Quick Start Guide April 2018

10 Rosemount 8600 Series Vortex Flowmeter

Andere Handbücher für Rosemount 8600D Series

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Emerson

Emerson Rosemount BINOS 100 F Bedienungsanleitung

Emerson

Emerson AMS Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Rosemount 2130 Bedienungsanleitung

Emerson

Emerson Rosemount 8600 Series Bedienungsanleitung

Emerson

Emerson Rosemount Clarity II T56 Bedienungsanleitung

Emerson

Emerson Rosemount CT5100 Bedienungsanleitung

Emerson

Emerson Rosemount 3051CF DP Bedienungsanleitung

Emerson

Emerson Rosemount 585 Annubar Bedienungsanleitung

Emerson

Emerson Rosemount WPG Bedienungsanleitung

Emerson

Emerson Rosemount Oxymitter DR Bedienungsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson Rosemount 8700 Series Konfigurationshandbuch

Emerson

Emerson Machinery Health Expert CSI 2600 Bedienungsanleitung

Emerson

Emerson FloBoss 103 Kurzanleitung

Emerson

Emerson Rosemount 751 Bedienungsanleitung

Emerson

Emerson Rosemount 2090P Bedienungsanleitung

Emerson

Emerson Rosemount CT5100 Ex Bedienungsanleitung

Emerson

Emerson Rosemount FCL Series Bedienungsanleitung

Emerson

Emerson Daniel Series Bedienungsanleitung

Emerson

Emerson 404B Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson FB3000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung