Emerson Rosemount WPG: Rosemount SPG Bedienungsanleitung

Quick Start Guide

00825-0100-4145, Rev BB

February 2019

Rosemount™ Smart Pressure Gauge

This guide provides basic guidelines for Rosemount Smart Pressure Gauges. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, or intrinsically safe

(I.S.) installations. Refer to the Rosemount Smart Pressure Gauge Reference Manual for more

instruction. The manual and this guide are also available electronically.

NOTICE

Shipping considerations

The device is shipped with the battery installed.

Each device contains one “D” size primary lithium-thionyl chloride battery. Primary lithium

batteries are regulated in transportation by the U.S. Department of Transportation, and are also

covered by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the

responsibility of the shipper to ensure compliance with these or any other local requirements.

Consult current regulations and requirements before shipping.

WARNING

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance with appropriate local,

national, and international standards, codes, and practices.

Ensure device is installed in accordance with intrinsically safe or non-incendive field practices.

Electrical shock could cause death or serious injury.

Device must be installed to ensure a minimum antenna separation distance of 8 in. (20 cm) from

all persons.

Care must be taken during transportation of device to prevent electrostatic charge build-up.

Process leaks could result in death or serious injury.

Handle the device carefully.

Failure to follow these installation guidelines could result in death or serious injury.

Ensure only qualified personnel perform the installation.

Contents

Required equipment......................................3

What’s in the box........................................... 4

Optional: Power/device check........................6

Optional: Normal range indication option......7

Installation Procedure....................................8

Troubleshooting.......................................... 12

Product Certifications.................................. 13

Quick Start Guide February 2019

2 Emerson.com/Rosemount

1 Required equipment

Figure 1-1: Anti-seize paste or PTFE tape (for NPT threaded connection)

Figure 1-2: Standard tools (e.g., screwdriver, wrench, pliers)

February 2019 Quick Start Guide

Quick Start Guide 3

2 What’s in the box

Smart Pressure Gauge Quick Start Guide

The following options are also available and will ship with the Rosemount

Smart Pressure Gauge if ordered.

Rosemount 306 Integral Manifold (model

code S5)

B4 bracket (model code B4)

Quick Start Guide February 2019

4 Emerson.com/Rosemount

Rosemount 1199 Seal(model code S1) Product Certification

Q4: Calibration Cert

QG: Calibration Cert and GOST

Verification Cert

QP: Calibration Cert and Tamper Evident

Seal

Q8: Material Traceability cert per EN

102043.1

Q15: Cert of Compliance to NACE

MR0175/ISO 15156 for wetted materials

Q25: Cert of Compliance to NACE

MR00103 for wetted materials

Normal range Indication (model code LK) Product Certification model codes

February 2019 Quick Start Guide

Quick Start Guide 5

3 Optional: Power/device check

The device is designed to be installation-ready.

Procedure

1. To check device battery prior to installation, perform Turn on device

2. Slide the ON/OFF switch to the OFF position until ready for use.

Quick Start Guide February 2019

6 Emerson.com/Rosemount

4 Optional: Normal range indication option

Important

•The stickers are intended to be installed on the dial only and should not be

applied on the inside or outside of the housing cover.

•Stickers should be applied in an environment where the ambient

temperature is above 50°F (10°C)

Procedure

1. Modify each of the stickers to desired size.

2. Remove housing cover.

3. Slide ON/OFF switch to the OFF position and wait for the LED to stop

flashing.

4. Gently move the needle in the clockwise direction until it is pointing at

the red X.

NOTICE

Equipment Damage

Use caution as the electronics assembly is connected to the needle.

5. Remove any debris on the dial, so it does not become trapped under

the sticker.

6. Peel back the white paper backing of the sticker.

7. Slowly lower the sticker onto the surface of the dial in the desired

location and rub it in place firmly. Repeat steps Step 6 and Step 7 until

desired indication locations are set.

Moving the sticker after initial contact is not recommended as this

decreases the amount of adhesive on the back of the sticker.

8. Slide ON/OFF switch to the ON position.

9. Replace housing cover.

February 2019 Quick Start Guide

Quick Start Guide 7

5 Installation Procedure

Procedure

1. Seal and protect threads

2. Mount device

Note

Use wrench on flats, not on housing.

5.1 Mounting orientation

The low side pressure port (atmospheric reference) is located in the neck of

the device behind the housing.

The vent path is between the housing and sensor.

CAUTION

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the device so the process can drain away.

Quick Start Guide February 2019

8 Emerson.com/Rosemount

Figure 5-1: Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

5.2 Turn on device

Check to ensure the device and battery are working properly.

Procedure

1. Twist the cover counterclockwise to remove it.

2. Slide the OFF/ON switch to the ON position to initiate the power

sequence.

Note

During the power sequence, the dial tests full range of motion and LED

flashes amber.

3. Once the power sequence ends, verify that the LED flashes green.

The LED may display several colors; see Device status indicator .

February 2019 Quick Start Guide

Quick Start Guide 9

5.3 Connect to the device

Image displaying the device connection diagram

1 2 3

64 5

8 7

A. Field Communicator

B. HART® Modem

C. AMS Configurator

5.3.1 AMS Configurator

Procedure to connect the AMS Configurator to the smart pressure gauge.

Procedure

1. Start AMS Configurator.

2. From the View menu, select Device Connection View.

3. Double-click the device under the HART modem.

5.3.2 Field communicator

Procedure to connect the smart pressure gauge to the field communicator.

Procedure

1. Turn on the Field Communicator.

2. From the Main menu, select the HART symbol.

5.4 Eliminate mounting effects

Devices are factory-calibrated. Once installed, it is recommended to perform

this step to eliminate potential error caused by mounting position or static

pressure.

Quick Start Guide February 2019

10 Emerson.com/Rosemount

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson Rosemount 3812 Programmierhandbuch

Emerson

Emerson Rosemount 8732 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount Oxymitter DR Bedienungsanleitung

Emerson

Emerson Rosemount Clarity II T56 Bedienungsanleitung

Emerson

Emerson Daniel 3415 Programmierhandbuch

Emerson

Emerson Rosemount 285 Bedienungsanleitung

Emerson

Emerson FB2100 Bedienungsanleitung

Emerson

Emerson Rosemount X-Stream Series Bedienungsanleitung

Emerson

Emerson Rosemount 370XA Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson 56WM WirelessHART SensEnable Bedienungsanleitung

Emerson

Emerson Rosemount 2090P Bedienungsanleitung

Emerson

Emerson Micro Motion TA Series Bedienungsanleitung

Emerson

Emerson Micro Motion 1700 Kurzanleitung

Emerson

Emerson Micro Motion HPC010P Bedienungsanleitung

Emerson

Emerson X-STREAM XE Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount 585 Annubar Bedienungsanleitung

Emerson

Emerson Rosemount CT5100 Bedienungsanleitung

Emerson

Emerson R&S SGT100A Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson 250-5000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung