Emerson Rosemount 3051S ERS Bedienungsanleitung

Quick Start Guide

00825-0100-4805, Rev FE

February 2019

Rosemount™ 3051S Transmitter

with FOUNDATION™ Fieldbus protocol

Safety messages

NOTICE

This guide provides basic guidelines for Rosemount™ 3051S Series Pressure Transmitters. It also

provides the basic electronic guidelines for the Rosemount 3051SFA Reference Manual, Rosemount

3051SFC Reference Manual, and Rosemount 3051SFP Reference Manual. It does not provide

instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Rosemount 3051S

HART Reference Manual for more instruction. This document is also available electronically on

Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

•Do not remove the transmitter cover in explosive atmospheres when the circuit is live.

•Both transmitter covers must be fully engaged to meet explosion-proof requirements.

•Ensure device is installed in accordance with intrinsically safe or non-incendive field practices.

Process leaks could result in death or serious injury.

•To avoid process leaks, only use the O-ring designed to seal with the corresponding flange

adapter.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Contents

Mount the transmitter................................... 3

Tagging....................................................... 10

Consider housing rotation............................12

Connect wiring and power up...................... 13

Verify configuration..................................... 21

Trim the transmitter.................................... 23

Rosemount 3051S/3051SFx/3051S-ERS

Product Certifications.................................. 24

Rosemount 3051S Declaration of Conformity

.................................................................... 40

China RoHS.................................................. 44

Quick Start Guide February 2019

2 Rosemount 3051S

1 Mount the transmitter

1.1 Liquid flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented

upward.

A. Direction of flow

1.2 Gas flow applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

A. Direction of flow

February 2019 Quick Start Guide

Quick Start Guide 3

1.3 Steam flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

A. Direction of flow

1.4 Using a mounting bracket

If the transmitter requires the use of a mounting bracket, use the images

below for instructions on how to properly mount the transmitter using the

Emerson™ provided mounting brackets. Use only bolts provided with the

transmitter or sold as Emerson spare parts.

1.4.1 Mounting brackets

Figure 1-1: Mounting Bracket – Coplanar Flange

Panel mount Pipe mount

Quick Start Guide February 2019

4 Rosemount 3051S

Figure 1-2: Mounting Brackets – Traditional Flange

Panel mount Pipe mount

Figure 1-3: Mounting Brackets – In-line

Panel mount Pipe mount

February 2019 Quick Start Guide

Quick Start Guide 5

1.5 Bolting considerations

If the transmitter installation requires assembly of a process flange, manifold,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitter. Only use bolts

supplied with the transmitter or sold by Emerson™ as spare parts. Figure 1-4

illustrates common transmitter assemblies with the bolt length required for

proper transmitter assembly.

Figure 1-4: Common Transmitter Assemblies

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional Rosemount Conventional

Manifold and flange adapters

Quick Start Guide February 2019

6 Rosemount 3051S

Note

For all other manifolds, contact Customer Central technical support.

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 1-1 . If

bolt material is not shown in Table 1-1, contact the local Emerson

representative for more information.

Use the following bolt installation procedure:

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 1-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 1-1 for final torque value.

5. Verify the flange bolts are protruding through the sensor module

before applying pressure (see Figure 1-5).

Example

Table 1-1: Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial torque Final torque

Carbon Steel

(CS)

B7M

300 in-lb 650 in-lb

Stainless Steel

(SST)

316

STM

316

B8M

150 in-lb 300 in-lb

February 2019 Quick Start Guide

Quick Start Guide 7

Figure 1-5: Proper Bolt Installation

A. Bolt

B. Sensor module

1.6 O-rings with flange adapters

WARNING

Failure to install proper flange adapter O-rings may cause process leaks, which

can result in death or serious injury. Only use the O-ring that is designed for its

specific flange adapter.

A. Flange adapter

B. O-ring

C. PTFE-based profile (square)

D. Elastomer profile (round)

Whenever the flange or adapters are removed, visually inspect the O-rings.

Replace them if there are any signs of damage, such as nicks or cuts. If the O-

rings are replaced, re-torque the flange bolts and alignment screws after

installation to compensate for seating of the O-rings.

1.7 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located under the sensor module neck label. (See Figure 1-6)

Quick Start Guide February 2019

8 Rosemount 3051S

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that any contaminants

can drain away.

Figure 1-6: In-line Gage Transmitter

A. Low side pressure port (under neck label)

February 2019 Quick Start Guide

Quick Start Guide 9

2 Tagging

Commissioning (paper) tag

To identify which device is at a particular location, use the removable tag

provided with the transmitter. Ensure the physical device tag (PD Tag field) is

properly entered in both places on the commissioning tag. Tear off the

bottom portion of the tag and write “physical tag” on this portion. This can

now be given to the person who can associate the device ID to the desired

tag.

Figure 2-1: Commissioning Tag for FOUNDATION Fieldbus revision ITK5

(default option)

Revision: 23

Device Serial Number:

XXXXXXXXXX

Device ID:

0011513051010001440-121698091725

PD Tag:

Tear Here

COMMISSIONING TAG

Device ID:

0011513051010001440-121698091725

PD Tag:

PT- 101

Revision: 23

Support files available at

Emerson.com/Rosemount

PT-101

Support files available at

Emerson.com/Rosemount

Quick Start Guide February 2019

10 Rosemount 3051S

Andere Handbücher für Rosemount 3051S ERS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 2088 Bedienungsanleitung

Emerson

Emerson Rosemount Analytical HART SMART 5081C-HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 2090P Bedienungsanleitung

Emerson

Emerson Rosemount 1151 Bedienungsanleitung

Emerson

Emerson Rosemount 3051P Bedienungsanleitung

Emerson

Emerson Rosemount 5600 Series Bedienungsanleitung

Emerson

Emerson Rosemount Ultrasonic 3107 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Konfigurationshandbuch

Emerson

Emerson Rosemount 648 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 1056 Bedienungsanleitung

Emerson

Emerson Rosemount 1408A Bedienungsanleitung

Emerson

Emerson Rosemount CX1100 Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount 3100 Series Bedienungsanleitung

Emerson

Emerson Rosemount 5081 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount ET310C Bedienungsanleitung

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung