Emerson Rosemount 3051S Series Bedienungsanleitung

Quick Start Guide

00825-0300-4801, Rev CA

December 2018

Rosemount™ 3051S Series Pressure

Transmitter and 3051SF Series Flow

Meter

with Advanced HART® Diagnostics

Safety messages

NOTICE

This guide provides basic guidelines for Rosemount™ 3051S Series Pressure Transmitters. It also

provides the basic electronic guidelines for the Rosemount 3051SFA Reference Manual, Rosemount

3051SFC Reference Manual, and Rosemount 3051SFP Reference Manual. It does not provide

instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Rosemount 3051S

HART Reference Manual for more instruction. This document is also available electronically on

Emerson.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of this

manual for any restrictions associated with a safe installation.

•Before connecting a handheld communicator in an explosive atmosphere, make sure the

instruments in the loop are installed in accordance with intrinsically safe or non-incendive field

wiring practices.

•In an explosion-proof/flameproof installation, do not remove the transmitter covers when power

is applied to the unit.

•Verify the operating atmosphere of the transmitter is consistent with the appropriate hazardous

locations certifications.

•Use appropriately rate Ex adapters, blanking elements, or glands during installation.

•Keep process insulation at least 1 inch (25 mm) from transmitter connection.

Process leaks could result in death or serious injury.

•Install and tighten process connectors before applying pressure.

•To avoid process leaks, only use the O-ring designed to seal with the corresponding flange

adapter.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

•Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.

Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all

entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a

compatible thread form when closing these entries.

•When installing in a hazardous location, use only appropriately listed or Ex certified plugs, glands,

or adapters in cable/conduit entries.

Contents

System readiness........................................... 5

Mount the transmitter................................... 7

Consider housing rotation............................13

Set the switches and jumpers.......................14

Connect wiring and power up...................... 15

Configuration verification............................ 19

Quick Start Guide December 2018

2 Rosemount 3051S Advanced HART

Trim the transmitter.................................... 21

Safety instrumented systems.......................23

Rosemount 3051S/3051SFx/3051S-ERS

Product Certifications.................................. 24

Rosemount 3051S Declaration of Conformity

.................................................................... 40

China RoHS.................................................. 44

December 2018 Quick Start Guide

Quick Start Guide 3

Quick Start Guide December 2018

4 Rosemount 3051S Advanced HART

1 System readiness

1.1 Confirm HART Revision capability

About this task

Not all systems are capable of communicating with HART® Revision 7

protocol. This transmitter can be configured for either HART Revision 5 or 7.

Note

Before installing the transmitter, confirm the correct device driver is loaded

on the host systems.

Procedure

1. If using HART based control or asset management systems, confirm

the HART capability of those systems prior to transmitter installation.

2. Reference the Rosemount™ 3051S Reference Manual for instructions

on how to change the HART revision of the transmitter.

1.2 Confirm correct device driver

Procedure

1. Verify the latest device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

2. Download the latest device driver at Emerson.com or

FieldCommGroup.org.

1.3 Device revisions and drivers

Table 1-1 provides the information necessary to ensure you have the correct

device driver and documentation for your device.

Table 1-1: Device Revisions and Files

Identify device Find device driver Review

instructio

Review

functiona

lity

Software

release

date

NAMUR

software

revision(1

)

HART

software

revision(2

)

HART

universal

revision

Device

revision(3

)

Manual

documen

t number

Changes

software(

Apr-16 1.0.0 20 7 4 00809-01

00-4801

See (4) for

list of

changes.

5 3

December 2018 Quick Start Guide

Quick Start Guide 5

Table 1-1: Device Revisions and Files (continued)

Identify device Find device driver Review

instructio

Review

functiona

lity

Oct-10 N/A 12 5 3 00809-01

00-4801

Added

Power

Advisory,

Output,

Power

Consumpt

ion,

Coefficien

t of

Variation

May-07 N/A 7 5 2 00809-01

00-4801

Update

Statistical

Process

Monitorin

Capability

Sep-06 N/A 4, 5, 6 5 1 00809-01

00-4801

N/A

(1) NAMUR software revision is located on the hardware tag of the device. In

accordance with NE53, revisions of the least significant level X (of 1.0.X) do not

change functionality or operation of the device and will not be reflected in the

review functionality column.

(2) HART software revision can be read using a HART capable configuration tool.

(3) Device driver file names use Device and DD Revision, e.g. 10_01. HART Protocol is

designed to enable legacy device driver revisions to continue to communicate with

new HART devices. To access new functionality, the new device driver must be

downloaded. It is recommended to download new device driver files to ensure full

functionality.

(4) HART Revision 5 and 7 selectable.

Quick Start Guide December 2018

6 Rosemount 3051S Advanced HART

2 Mount the transmitter

If the transmitter requires the use of a mounting bracket, use the images for

instructions on how to properly mount the transmitter using the Emerson™

provided mounting brackets. Use only bolts provided with the transmitter or

sold as Emerson spare parts

2.1 Liquid flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented

upward.

A. Direction of flow

2.2 Gas flow applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

December 2018 Quick Start Guide

Quick Start Guide 7

A. Direction of flow

2.3 Steam flow applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

A. Direction of flow

2.4 Mounting brackets

Figure 2-1: Mounting Bracket – Coplanar Flange

Panel mount Pipe mount

Quick Start Guide December 2018

8 Rosemount 3051S Advanced HART

Figure 2-2: Mounting Brackets – Traditional Flange

Panel mount Pipe mount

Figure 2-3: Mounting Brackets – In-line

Panel mount Pipe mount

2.5 Bolting considerations

About this task

If the transmitter installation requires assembly of a process flange, manifold,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitter. Only use bolts

supplied with the transmitter or sold by Emerson™ as spare parts. Figure 2-4

illustrates common transmitter assemblies with the bolt length required for

proper transmitter assembly.

December 2018 Quick Start Guide

Quick Start Guide 9

Figure 2-4: Common Transmitter Assemblies

4 × 1.75-in.

(44 mm)

4 × 1.75-in.

(44 mm)

4 × 2.25-in.

(57 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 2.88-in.

(73 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional Rosemount Conventional

Manifold and flange adapters

Note

For all other manifolds, contact Customer Central technical support.

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 2-1 . If

bolt material is not shown in Table 2-1, contact the local Emerson

representative for more information.

Use the following bolt installation procedure:

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 2-1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 2-1 for final torque value.

Quick Start Guide December 2018

10 Rosemount 3051S Advanced HART

Andere Handbücher für Rosemount 3051S Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount5081 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 1057 Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Emerson

Emerson Rosemount OCX8800A Bedienungsanleitung

Emerson

Emerson Rosemount 3300 Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051SF Series Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Micro Motion 4200 Bedienungsanleitung

Emerson

Emerson Rosemount 1152 Alphaline Bedienungsanleitung

Emerson

Emerson Rosemount 1151 Bedienungsanleitung

Emerson

Emerson Fisher 4211 Bedienungsanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount 1057 Bedienungsanleitung

Emerson

Emerson Rosemount 3095FC MultiVariable Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Series Bedienungsanleitung

Emerson

Emerson Rosemount 8782 Bedienungsanleitung

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Micro Motion 2500 Kurzanleitung

Emerson

Emerson Rosemount 1208 Bedienungsanleitung

Emerson

Emerson Rosemount ET210 Bedienungsanleitung

Emerson

Emerson Rosemount 3051P Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung