Endress+Hauser CCS240 Bedienungsanleitung

Products Solutions Services

Operating Instructions

CCS240/241

Sensors for measuring chlorine dioxide

BA00114C/07/EN/14.18

71423118

2018-10-23

CCS240/241 Table of contents

Endress+Hauser 3

Table of contents

1 About this document ........... 4

1.1 Warnings ........................... 4

1.2 Symbols used ........................ 4

2 Basic safety instructions ....... 6

2.1 Requirements for the personnel ........ 6

2.2 Designated use ...................... 6

2.3 Workplace safety .................... 6

2.4 Operational safety ................... 6

2.5 Product safety ....................... 7

3 Product description ............. 7

3.1 Product design ....................... 7

4 Incoming acceptance and

product identification ......... 10

4.1 Incoming acceptance ................ 10

4.2 Product identification ................ 10

5 Installation .................... 12

5.1 Installation conditions ............... 12

5.2 Mounting the sensor ................ 13

5.3 Post-installation check ............... 15

6 Electrical connection .......... 15

6.1 Connecting the sensor ............... 16

6.2 Ensuring the degree of protection ..... 18

6.3 Post-connection check ............... 18

7 Commissioning ................ 19

7.1 Function check ..................... 19

7.2 Sensor polarization .................. 19

7.3 Sensor calibration ................... 19

8 Diagnostics and

troubleshooting ............... 21

9 Maintenance .................. 23

9.1 Maintenance schedule ............... 23

9.2 Maintenance tasks .................. 23

10 Repair .......................... 30

10.1 Spare parts ........................ 30

10.2 Return ............................ 30

10.3 Disposal ........................... 30

11 Accessories .................... 31

11.1 Device-specific accessories ............ 31

12 Technical data ................. 32

12.1 Input .............................. 32

12.2 Performance characteristics .......... 33

12.3 Environment ....................... 33

12.4 Process ............................ 33

12.5 Mechanical construction ............. 34

Index ................................. 35

About this document CCS240/241

4 Endress+Hauser

1 About this document

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious injury.

LWARNING

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious injury.

LCAUTION

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

If necessary, Consequences of non-

compliance (if applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to property.

1.2 Symbols used

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

CCS240/241 About this document

Endress+Hauser 5

1.2.1 Symbols on the device

Symbol Meaning

Reference to device documentation

Basic safety instructions CCS240/241

6 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for the personnel

Installation, commissioning, operation and maintenance of the measuring system may be

carried out only by specially trained technical personnel.

‣The technical personnel must be authorized by the plant operator to carry out the specified

activities.

‣The electrical connection may be performed only by an electrical technician.

‣The technical personnel must have read and understood these Operating Instructions and

must follow the instructions contained therein.

‣Measuring point faults may be repaired only by authorized and specially trained personnel.

Repairs not described in the Operating Instructions provided must be carried out only

directly at the manufacturer's site or by the service organization.

2.2 Designated use

Drinking water and industrial water must be disinfected through the addition of appropriate

disinfectants such as chlorine gas or inorganic chlorine compounds. The dosing quantity must

be adapted to continuously fluctuating operating conditions. If the concentrations in the water

are too low, this could jeopardize the effectiveness of the disinfection. On the other hand,

concentrations which are too high can lead to signs of corrosion and have an adverse effect on

taste, as well as generating unnecessary costs.

The sensor was specifically developed for this application and is designed for continuous

measurement of chlorine dioxide in water. In conjunction with measuring and control

equipment, it allows optimal control of disinfection.

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Workplace safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable European standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

2.4 Operational safety

Before commissioning the entire measuring point:

1. Verify that all connections are correct.

CCS240/241 Product description

Endress+Hauser 7

2. Ensure that electrical cables and hose connections are undamaged.

3. Do not operate damaged products, and protect them against unintentional operation.

4. Label damaged products as defective.

During operation:

‣If faults cannot be rectified:

products must be taken out of service and protected against unintentional operation.

2.4.1 Special instructions

‣Do not operate the sensors under process conditions where it is expected that osmotic

conditions will cause electrolyte components to pass through the membrane and into the

process.

2.5 Product safety

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

European standards have been observed.

3 Product description

3.1 Product design

The sensor consists of the following functional units:

• Measuring chamber

– To protect the anode or cathode from the medium

– With a large volume of electrolyte for a long service life in combination with the large

anode and the small cathode

• Sensor shaft with

– Large anode

– Cathode embedded in plastic

– Optional temperature sensor

• Membrane cap with

– Robust PTFE membrane

– Special support grid between cathode and membrane for a defined and consistent

electrolyte film and thus a relatively constant indication even at varying pressures and

flows

Product description CCS240/241

8 Endress+Hauser

A0037109

1 Fixed cable

2 Sensor shaft

3 O-ring

4 Large anode, silver/silver chloride

5 Gold cathode

6 Measuring chamber

7 Membrane cap with dirt-repellent membrane

8 Screw cap for securing the membrane cap

3.1.1 Measuring principle

Chlorine dioxide levels are determined in accordance with the amperometric measuring

principle.

The chlorine dioxide (ClO2) in the medium diffuses through the sensor membrane and is

reduced to chloride ions (Cl-) at the gold cathode. At the silver anode, silver is oxidized to

silver chloride. Electron donation at the gold cathode and electron acceptance at the silver

anode cause a current to flow which is proportional to the concentration of chlorine dioxide in

the medium. This process does not depend on the pH value over a wide range.

The transmitter uses the current signal to calculate the measured variable for concentration in

mg/l (ppm).

3.1.2 Effects on the measured signal

Flow

The minimum flow velocity of the membrane-covered measuring cell is 15 cm/s (0.5 ft/s).

When using the CCA250 flow assembly, this corresponds to a flow rate of 30 l/h (7.9 gal/h)

(upper edge of float at level of red bar mark).

At higher flow rates, the measured signal is virtually flow-independent. However, if the flow

rate falls below the specified value, the measured signal depends on the flow.

CCS240/241 Product description

Endress+Hauser 9

The installation of an INS proximity switch in the assembly enables reliable detection of this

invalid operating status, thus triggering an alarm or causing the dosing process to be switched

off if necessary.

Below the minimum flow rate, the sensor current is more sensitive to flow fluctuations. For

abrasive media, it is recommended not to exceed the minimum flow. If suspended solids are

present, which may form deposits, the maximum flow rate is recommended.

Temperature

Changes in the temperature of the medium affect the measured value:

• Increases in temperature result in a higher measured value (approx. 4 % per K)

• Decreases in temperature result in a lower measured value.

Using the sensor in combination with the Liquisys CCM223/253 enables automatic

temperature compensation (ATC). Recalibration in the case of temperature changes is not

necessary.

1. If automatic temperature compensation is disabled at the transmitter, the temperature

must be maintained at a constant level following calibration.

2. Otherwise, recalibrate the sensor.

Incoming acceptance and product identification CCS240/241

10 Endress+Hauser

4 Incoming acceptance and product identification

4.1 Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify the supplier of any damage to the packaging.

Keep the damaged packaging until the issue has been resolved.

2. Verify that the contents are undamaged.

 Notify the supplier of any damage to the delivery contents.

Keep the damaged goods until the issue has been resolved.

3. Check that the delivery is complete and nothing is missing.

 Compare the shipping documents with your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.

 The original packaging offers the best protection.

Make sure to comply with the permitted ambient conditions.

If you have any questions, please contact your supplier or your local Sales Center.

4.2 Product identification

4.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Extended order code

• Serial number

• Safety information and warnings

‣Compare the information on the nameplate with the order.

4.2.2 Product page

www.endress.com/ccs240

www.endress.com/ccs241

4.2.3 Interpreting the order code

The order code and serial number of your product can be found in the following locations:

• On the nameplate

• In the delivery papers

Obtaining information on the product

1. Go to www.endress.com.

2. Call up the site search (magnifying glass).

3. Enter a valid serial number.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Endress+Hauser Zubehör Handbücher

Endress+Hauser

Endress+Hauser Oxymax H COS21 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Prosonic S FDU91 Handbuch

Endress+Hauser

Endress+Hauser Deltabar FMD71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CLS15D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Nivector FTI26 Technische Daten

Endress+Hauser

Endress+Hauser Proline 800 Technische Daten

Endress+Hauser

Endress+Hauser NAR 300 Technische Daten

Endress+Hauser

Endress+Hauser CCS50D Bedienungsanleitung

Endress+Hauser

Endress+Hauser CCS140 Bedienungsanleitung

Endress+Hauser

Endress+Hauser OUSAF44 Bedienungsanleitung

Endress+Hauser

Endress+Hauser NAR 300 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 200 FOUNDATION Fieldbus Technische Daten

Endress+Hauser

Endress+Hauser Oxymax COS61 Handbuch

Endress+Hauser

Endress+Hauser Liquiphant M FTL51C Bedienungsanleitung

Endress+Hauser

Endress+Hauser Micropilot M FMR230 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Memosens COS51E Bedienungsanleitung

Endress+Hauser

Endress+Hauser ISEmax CAS40D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Oxymax COS22 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser OxyMax W COS 41 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Oxymax H COS21D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Turbimax CUS51D Handbuch

Endress+Hauser

Endress+Hauser Deltapilot M FMB50 Technische Daten

Endress+Hauser

Endress+Hauser Oxymax W COS61 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Turbimax W CUS31 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung