Endress+Hauser Turbimax CUS71D Bedienungsanleitung

Products Solutions Services

Operating Instructions

Turbimax CUS71D

Ultrasonic interface sensor

BA00490C/07/EN/05.16

71353737

AUTHORIZED DISTRIBUTOR:

InstrumentsAndControl.com

Houston, Texas USA

[email protected]

281-609-7170

Turbimax CUS71D Table of contents

Endress+Hauser 3

Table of contents

1 Document information ......... 4

1.1 Warnings ........................... 4

1.2 Symbols used ........................ 4

2 Basic safety instructions ....... 5

2.1 Requirements for personnel ........... 5

2.2 Designated use ...................... 5

2.3 Occupational safety .................. 6

2.4 Operational safety ................... 7

2.5 Product safety ....................... 7

3 Product description ............. 8

3.1 Product design ....................... 8

4 Incoming acceptance and

product identification .......... 8

4.1 Incoming acceptance ................. 8

4.2 Product identification ................. 9

5 Installation .................... 11

5.1 Installation conditions ............... 11

5.2 Mounting the sensor ................ 14

5.3 Post-installation check ............... 18

6 Electrical connection .......... 18

6.1 Connecting the sensor ............... 18

6.2 Post-connection check ............... 20

7 Commissioning ................ 20

7.1 Preparatory steps ................... 20

8 Operation ...................... 20

8.1 Sensor monitoring .................. 20

8.2 Cyclic cleaning ...................... 20

8.3 Automatic wiper function ............ 21

9 Diagnostics and

troubleshooting ............... 21

10 Maintenance .................. 21

10.1 Maintenance tasks .................. 22

11 Repairs ......................... 23

11.1 Spare parts ........................ 23

11.2 Return ............................ 23

11.3 Disposal ........................... 23

12 Accessories .................... 24

12.1 Assemblies ........................ 24

12.2 Holder ............................ 25

12.3 Cable extension ..................... 26

13 Technical data ................. 26

Index ................................. 28

Document information Turbimax CUS71D

4 Endress+Hauser

1 Document information

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

Consequences of non-compliance (if

applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious injury.

LWARNING

Causes (/consequences)

Consequences of non-compliance (if

applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious injury.

LCAUTION

Causes (/consequences)

Consequences of non-compliance (if

applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

Consequences of non-compliance (if

applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to property.

1.2 Symbols used

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

Turbimax CUS71D Basic safety instructions

Endress+Hauser 5

1.2.1 Symbols on the device

Symbol Meaning

Reference to device documentation

2 Basic safety instructions

2.1 Requirements for personnel

• Installation, commissioning, operation and maintenance of the measuring system may be

carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the specified

activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions and

must follow the instructions contained therein.

• Measuring point faults may be repaired only by authorized and specially trained personnel.

Repairs not described in the Operating Instructions provided may only be carried out

directly by the manufacturer or by the service organization.

2.2 Designated use

CUS71D is a sensor designed for interface measurement in water and wastewater.

The sensor is particularly suited for use in the following applications:

• Wastewater treatment: primary clarifier, sludge thickener, secondary clarifier

• Water treatment: sedimentation tank after flocculant dosage, sludge height in contact

sludge processes

• Static separation processes: with/without slow stirring and without introduction of air

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

NOTICE

Non-designated use

Incorrect measurements, malfunctions and even measuring point failure could result

‣Only use the product in accordance with the product specifications.

‣Pay particular attention to the technical data on the nameplate.

Basic safety instructions Turbimax CUS71D

6 Endress+Hauser

2.3 Occupational safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable European standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

Turbimax CUS71D Basic safety instructions

Endress+Hauser 7

2.4 Operational safety

1. Before commissioning the entire measuring point, verify that all connections are

correct. Ensure that electrical cables and hose connections are undamaged.

2. Do not operate damaged products, and safeguard them to ensure that they are not

operated inadvertently. Label the damaged product as defective.

3. If faults cannot be rectified:

Take the products out of operation and safeguard them to ensure that they are not

operated inadvertently.

2.5 Product safety

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

European standards have been observed.

We only provide a warranty if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the device settings.

IT security measures in line with operators' security standards and designed to provide

additional protection for the device and device data transfer must be implemented by the

operators themselves.

Product description Turbimax CUS71D

8 Endress+Hauser

3 Product description

3.1 Product design

The sensor is designed for continuous in-situ determination of interfaces.

The sensor includes all necessary modules:

• Power supply

• The ultrasonic source emits the measurement signals.

• The ultrasonic receiver receives the measurement signals, digitalizes the signals and

converts them to a measurement value.

• The sensor microcontroller controls the internal operations and data transmission.

The preconfigured sensor can be used at a measuring point.

3.1.1 Measuring principle

A piezoelectric crystal is enclosed in a flat cylindrical plastic housing. When the crystal is

excited by an electrical voltage, it generates a sonar signal. This causes ultrasonic waves to be

transmitted at a frequency of approx. 650 kHz and at an angle of 6° to scan the separation

zones.

The measured variable is the time the transmitted ultrasonic signal needs to reach the solid

particles in the separation zone and return to the receiver. The separation zone is computed

after the maximum slope and the maximum signal amplitude.

A sensor version featuring a wiper is available to reliably avoid the buildup of deposit on the

sensor membrane.

4 Incoming acceptance and product identification

4.1 Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify your supplier of any damage to the packaging.

Keep the damaged packaging until the matter has been settled.

2. Verify that the contents are undamaged.

 Notify your supplier of any damage to the delivery contents.

Keep the damaged products until the matter has been settled.

3. Check the delivery for completeness.

 Check it against the delivery papers and your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.

 The original packaging offers the best protection.

The permitted ambient conditions must be observed (see "Technical data").

If you have any questions, please contact your supplier or your local sales center.

Turbimax CUS71D Incoming acceptance and product identification

Endress+Hauser 9

4.2 Product identification

4.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Extended order code

• Serial number

• Ambient and process conditions

• Safety information and warnings

Compare the data on the nameplate with your order.

4.2.2 Product identification

The order code and serial number of your product can be found in the following locations:

• On the nameplate

• In the delivery papers

Obtaining information on the product

1. Go to the product page for your product on the Internet.

2. At the bottom of the page, click the link Online Tools and then select Access device

specific information.

 An additional window opens.

3. Enter the order code from the nameplate into the search field and then select Show

details.

 You will receive information on each feature (selected option) of the order code.

Manufacturer's address

Endress+Hauser Conducta GmbH+Co. KG

Dieselstraße 24

D-70839 Gerlingen

4.2.3 Scope of delivery

The delivery comprises:

• 1 Turbimax CUS71D sensor, version as ordered

• 1 set of Operating Instructions BA00490C/07/EN

If you have any questions, please contact your supplier or your local sales center.

4.2.4 Certificates and approvals

Declaration of Conformity

The product meets the requirements of the harmonized European standards. As such, it

complies with the legal specifications of the EU directives. The manufacturer confirms

successful testing of the product by affixing to it the  mark.

Incoming acceptance and product identification Turbimax CUS71D

10 Endress+Hauser

EAC

The product has been certified according to guidelines TP TC 004/2011 and TP TC 020/2011

which apply in the European Economic Area (EEA). The EAC conformity mark is affixed to the

product.

Electromagnetic compatibility

Interference emission and interference immunity: Industrial environment as per

• EN 61326-1:2013

• EN 61326-2-3:2013

• NAMUR NE21: 2012

Andere Handbücher für Turbimax CUS71D

Inhaltsverzeichnis

Andere Endress+Hauser Zubehör Handbücher

Endress+Hauser

Endress+Hauser Oxymax W COS51D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Soliphant M FTM50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Levelflex FMP56 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltapilot M FMB50 Technische Daten

Endress+Hauser

Endress+Hauser CCS120 Bedienungsanleitung

Endress+Hauser

Endress+Hauser NAR 300 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 200 PROFIBUS PA Technische Daten

Endress+Hauser

Endress+Hauser Proline Promag H Technische Daten

Endress+Hauser

Endress+Hauser Oxymax W COS71 Handbuch

Endress+Hauser

Endress+Hauser CCS240 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Dipfit W CLA111 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Tophit CPS471 Handbuch

Endress+Hauser

Endress+Hauser Proline 200 FOUNDATION Fieldbus Technische Daten

Endress+Hauser

Endress+Hauser Nivector FTI26 Technische Daten

Endress+Hauser

Endress+Hauser OxyMax W COS 71 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Chloromax CCS142D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar S PMD70 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Solitrend MMP42 Technische Daten

Endress+Hauser

Endress+Hauser Proline 800 Technische Daten

Endress+Hauser

Endress+Hauser Oxymax COS22 Series Bedienungsanleitung

Endress+Hauser

Endress+Hauser Turbimax CUS51D Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline 800 Technische Daten

Endress+Hauser

Endress+Hauser OUSAF46 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar S FMD 77 Handbuch

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung