Equinox Systems Graphix Bedienungsanleitung

Order code: EQLED202

Graphix

User Manual

www.prolight.co.uk Graphix User Manual 2

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

Safety advice

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not sit the equipment on a at surface as this can

block the air intake to cool the LED.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Graphix User Manual 3

Product overview & technical specications

events or venues. Fitted with a rotating graphics wheel it outputs exciting patterns, whilst its multi-coloured mirror

dish features a pastel palette of colours adding a retro feel to this effect. The unit has a range of modes including

auto and sound active along with each attribute being controllable via DMX. The unit, although compact in size,

has a wide beam angle but still packs a punch over a long distance thanks to its superior optics and high

output LED.

• 1 x 100W warm white LED (3200K)

• Beam angle: 75°

• Manual focus

• Rotating graphics wheel

• Multi-coloured mirror dish

• DMX channels: 2/4 or 6 selectable

• Auto, sound active and master/slave modes

plus built-in programs

• 0-100% dimming and variable strobe

• Optional CA 8 controller

• Supplied with hanging bracket

• 4 push button menu with LED display

• IEC power input/output

• 3-Pin XLR input/output

• Fan cooled

Hallucination

Specications

Power consumption 121W

Power supply 100~240V, 50/60Hz

Fuse T2A 250V

Dimensions 186 x 308 x 199mm

Weight 3.8kg

Order code EQLED202

308mm 30mm

175mm

199mm

126mm

186mm

www.prolight.co.uk Graphix User Manual 4

Technical specications

01 - LED display

02 - Function buttons

03 - Microphone

04 - 3-Pin DMX input

05 - 3-Pin DMX output

06 - IEC power input

07 - IEC power output

08 - Fuse T2A 250V

09 - CA8 control input

10 - Hanging bracket

11 - Hanging bracket

adjustment knobs

12 - Safety eye

In the box: 1 x xture,

& 1 x power cable

MENUMIC ENTERDOWNUP

POWER

OUTPUT:

100-240V

~50/60Hz

POWER

INPUT:

100-240V

~50/60Hz

FUSE: T2A 250V

POWER CONSUMPTION: 115W

CA-8 INPUT

DMX OUTPUTDMX INPUT

www.prolight.co.uk

11 11

12 05 07

06040203 01

www.prolight.co.uk Graphix User Manual 5

Operating instructionsOperating instructionsOperating instructions

0 0 1

5 1 2

Addr

DMX address setting

C H n d

Channel modes

4 C h

6 C h

2 C h

o F F

o n

NAst

Master mode

S L 1

S L 2

SLnd

Slave mode

0 0 0

1 0 0

SEnS

Sound sensitivity

o N

o F F

SoUn

Sound active

d N S t

No DMX signal

nASt

LASt

b L n d

o N

oFF

L E d

Display blackout

Show modes

S H n d

S H - 0

S H - 4

SH-2

SH-8

S P 0 0

SP99

p 0 0 0

p 2 5 5

S H - 3

S P 0 0

S P 9 9

www.prolight.co.uk Graphix User Manual 6

Operating instructions

- - - -F H r s

Fixture hours

C - - -t E N p

Fixture temperature

U - - -U E r

Software version

N A n U

Manual mode

000

255

d i N N

000

255

S t r o

000

255

G o b o

000

255

r o t A

Offset Menu: Pattern wheel rotation/mirror

rotation home position adjustment

- 1 2 7

127

r o t A

G o b o

o n

o F F

dISP

Display invert

www.prolight.co.uk Graphix User Manual 7

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the xture and each xture independently.

To access the DMX address mode, press the “MENU” button and use the “UP” and “DOWN” buttons on

the rear of the unit to show Addr on the LED display. Now press the “ENTER” button and use the “UP”

and “DOWN” buttons to set the required DMX address. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

DMX channel mode:

To access the DMX channel mode, press the “MENU” button and use the “UP” and “DOWN” buttons on

the rear of the unit to show CHnd on the LED display. Now press the “ENTER” button and use the “UP”

and “DOWN” buttons to choose one of the 2/4 or 6 DMX channel modes. Press the “ENTER”

button to conrm the setting. To exit out of any of the above options, press the “MENU” button.

Operating instructions

2 channel mode:

Channel Value Function

CH1

000-003 Blackout

004-031 Show 0 (All shows)

032-059 Show 1 (Mirror dish and pattern wheel in both directions, no strobe)

060-087 Show 2 (Mirror dish and pattern wheel in both directions, no strobe, slow mode non-reactive to sound)

088-115 Show 3 (Mirror dish in both directions, pattern wheel static - selected in menu)

116-143 Show 4 (Mirror dish CW, pattern wheel CW)

144-171 Show 5 (Mirror dish CW, pattern wheel CCW)

172-199 Show 6 (Mirror dish CCW, pattern wheel CW)

200-227 Show 7 (Mirror dish CCW, pattern wheel CCW)

228-255 Show 8 (Mirror dish and pattern wheel in both directions, some strobe)

CH2 000-255 Show mode motor speed (slow-fast)

www.prolight.co.uk Graphix User Manual 8

4 channel mode:

Channel Value Function

CH1 000-255 Master dimmer (0-100%)

CH2

000-031 Blackout

032-063 Open

064-095 Strobe (slow-fast)

096-127 Open

128-159 Pulse (slow-fast)

160-191 Open

192-223 Random strobe (slow-fast)

224-255 Open

CH3

000-127 Pattern wheel index

128-191 Pattern wheel clockwise rotation

(fast-slow)

192-255 Pattern wheel anti-clockwise rotation

(fast-slow)

CH4

000-127 Mirror dish rotation index

128-191 Mirror dish anti-clockwise rotation

(fast-slow)

192-255 Mirror dish clockwise rotation

(fast-slow)

Operating instructions

6 channel mode:

Channel Value Function

CH1 000-255 Master dimmer (0-100%)

CH2

000-031 Blackout

032-063 Open

064-095 Strobe (slow-fast)

096-127 Open

128-159 Pulse (slow-fast)

160-191 Open

192-223 Random strobe (slow-fast)

224-255 Open

CH3

000-127 Pattern wheel index

128-191 Pattern wheel clockwise rotation

(fast-slow)

192-255 Pattern wheel anti-clockwise rotation

(fast-slow)

CH4

000-127 Mirror dish rotation index

128-191 Mirror dish anti-clockwise rotation

(fast-slow)

192-255 Mirror dish clockwise rotation

(fast-slow)

CH5

000-003 Blackout

004-031 Show 0 (All shows)

032-059 Show 1 (Mirror dish and pattern

wheel in both directions, no strobe)

060-087

Show 2 (Mirror dish and pattern

wheel in both directions, no strobe,

slow mode non-reactive to sound)

088-115

Show 3 (Mirror dish in both direc-

tions, pattern wheel static - selected

in menu)

116-143 Show 4 (Mirror dish CW, pattern

wheel CW)

144-171 Show 5 (Mirror dish CW, pattern

wheel CCW)

172-199 Show 6 (Mirror dish CCW, pattern

wheel CW)

200-227 Show 7 (Mirror dish CCW, pattern

wheel CCW)

228-255

Show 8 (Mirror dish and pattern

wheel in both directions, some

strobe)

CH6 000-255 Show mode motor speed (slow-fast)

www.prolight.co.uk Graphix User Manual 9

Operating instructions

Master/slave mode:

To set the master unit, press the “MENU” button and use the “UP” and “DOWN” buttons on the rear

of the unit to show NASt on the LED display. Now press the “ENTER” button and use the “UP” and

“DOWN” buttons to choose on choose oFF. Press the “ENTER” button to conrm the setting.

Then select your desired program.

To set the other units in slave mode, press the “MENU” button and use the “UP” and “DOWN” buttons

on the rear of the unit to show SLnd on the LED display. Now press the “ENTER” button and use the

“UP” and “DOWN” buttons to choose either SL1 (copies master) or SL2 (opposite mirror dish

rotation direction and glass wheel rotation direction to master).

Press the “ENTER” button to conrm the setting.

The unit will now run in sequence with the master unit.

To exit out of any of the above options, press the “MENU” button.

Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Show mode:

To access the show modes, press the “MENU” button and use the “UP” and “DOWN” buttons on the rear

of the unit to show SHnd on the LED display. Now press the “ENTER” button and use the “UP” and

“DOWN” buttons to choose between SH-0 ~ SH-8. Now press the “ENTER” button and use the “UP”

and “DOWN” buttons to select the speed between SP00 ~ SP99.

In Show 3 you can set a specic pattern. Press the “ENTER” button again and use the “UP” and “DOWN”

buttons to select the pattern between P000 ~ P255. Now press the “ENTER” button and use the

“UP” and “DOWN” buttons to select the speed between SP00 ~ SP99.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Sound active:

To access the sound active setting, press the “MENU” button and use the “UP” and “DOWN” buttons on

the rear of the unit to show SoUn on the LED display. Now press the “ENTER” button and use the “UP”

and “DOWN” buttons to choose between on or ofF. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

SH-0 Show 0 (All shows)

SH-1 Show 1 (Mirror dish and pattern wheel in both directions, no strobe)

SH-2 Show 2 (Mirror dish and pattern wheel in both directions, no strobe, slow mode non-reactive to sound)

SH-3 Show 3 (Mirror dish in both directions, pattern wheel static - selected in menu)

SH-4 Show 4 (Mirror dish CW, pattern wheel CW)

SH-5 Show 5 (Mirror dish CW, pattern wheel CCW)

SH-6 Show 6 (Mirror dish CCW, pattern wheel CW)

SH-7 Show 7 (Mirror dish CCW, pattern wheel CCW)

SH-8 Show 8 (Mirror dish and pattern wheel in both directions, some strobe)

www.prolight.co.uk Graphix User Manual 10

Sound sensitivity:

To adjust the sound sensitivity, press the “MENU” button and use the “UP” and “DOWN” buttons on the

rear of the unit to show SEns on the LED display. Now press the “ENTER” button and use the “UP”

and “DOWN” buttons to choose between 000 ~ 100. Press the “ENTER” button to conrm the setting.

Value: 0 - 100 (0 = low, 100 = high)

To exit out of any of the above options, press the “MENU” button.

DMX signal lost:

To change what the unit does when the DMX signal is lost, press the “MENU” button and use the “UP”

and “DOWN” buttons on the rear of the unit to show dNSt on the LED display. Now press the “ENTER”

button and use the “UP” and “DOWN” buttons to choose between nASt (Master/Slave),

LAst (Hold the last DMX command) or bLnd (Blackout).

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Display blackout:

To access the display blackout setting, press the “MENU” button and use the “UP” and “DOWN” buttons

on the rear of the unit to show LEd on the LED display. Now press the “ENTER” button and use the

“UP” and “DOWN” buttons to choose between on (display blacks out) or ofF(display always on).

Press the “ENTER” button to conrm the setting. To exit out of any of the above options, press the

“MENU” button.

Display invert setting:

To access the display invert setting, press the “MENU” button and use the “UP” and “DOWN” buttons on

the rear of the unit to show dIsp on the LED display. Now press the “ENTER” button and use the “UP”

and “DOWN” buttons to choose between on or ofF. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Manual mode:

To access manual mode, press the “MENU” button on the front of the unit to show NANU on the LED

display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between

diNN (Dimmer), Stro (Strobe), Gobo (Pattern wheel) or rOta (Mirror Rotation). Press the

“ENTER” button and use the “UP” and “DOWN” buttons to choose between 000 ~ 255.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Fixture temperature:

To access the xtures temperature, press the “MENU” button and use the “UP” and “DOWN” buttons on

the rear of the unit to show tENp on the LED display. Now press the “ENTER” button.

The unit will now display the xtures temperature.

To exit out of any of the above options, press the “MENU” button.

Operating instructions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems MaxiPar Tri MKII Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth LED Starcloth System Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Quad Bedienungsanleitung

Equinox Systems

Equinox Systems FXbar18 Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems CARBON Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems Micro Batt EQLED160 Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer RGB Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems PFM1500 Bedienungsanleitung

Equinox Systems

Equinox Systems Pulse Tube Lithium Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion 140 Bedienungsanleitung

Equinox Systems

Equinox Systems Triton Beam EQLED071 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED054 Bedienungsanleitung

Equinox Systems

Equinox Systems Kaleido XP Bedienungsanleitung

Equinox Systems

Equinox Systems MoonPar Bedienungsanleitung

Equinox Systems

Equinox Systems Helix 100W Gobo Flower Bedienungsanleitung

Equinox Systems

Equinox Systems Hallucination Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Quad Pix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Orbit Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED53 Bedienungsanleitung

Equinox Systems

Equinox Systems MIRR22 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung