Ergotron Carl's Table CT15 Bedienungsanleitung

OWNER'S MANUAL &TROUBLESHOOTING GUIDE

Carl's Table®: CT15

Part Number: CT15SM/DG

300-5642-00 rev. C

• /

Built with Anthro-DNA™

Thank you for purchasing Carl’s

Table, model CT15!

This Owner's Manual will show you

how to operate the table, how to

adjust the settings on Carl's Table,

and how to troubleshoot any prob-

lems in the unlikely event that the

table doesn't perform as designed.

If you have any questions or need

any help, please let us give us a call,

800.325.3841.

01 Fan Control

02 Fan

03 Task Light

04 Back Light Control Dial

05 Task Light Control Dial

06 Task Light Control Switch

07 Monitor Height Control

08 Monitor Depth Control

09 Table Height Control

10 Table Tilt Control

11 Safety Indicator Light

12 Position Preset Keypad

TABLE OF CONTENTSWELCOME

Fan

O

Comfort

Controls

123

456

789

Set 0Go

Preset

Tilt

Depth

Height

Table

Monitor

07 08

09 10

11 12

Back Light

Task Lights

Off

Lighting

Controls

Carl’s Table

CT15

Fan

Off

300-5642-00 rev. C

• /

Introduction

Carl’s Table is designed to provide comfort, privacy, and lighting by making the table very adjustable. Controls located on the

upper corners of the keyboard surface adjust the height (28" to 48") and tilt (0 to 15° ) of the table surfaces, the height and depth

of the monitors, air movement, and lighting. Available adjustments:

Anthro Monitor Control System®– Electronically adjust the height and depth of the monitors using the control pad on the right

side of the work surface. Adjust the tilt of each monitor manually.

Surfaces – Electronically adjust the height and tilt of CT15 to work while standing, sitting or reclining. Position the table

manually, or use the position preset feature and record your preferred height and tilt settings.

Adaptive Lighting System – Adjust the table's ambient light system manually to provide the optimal contrast ratio. Task lights

are also adjusted manually.

Air Circulation System – Two fans, one on the left side and one of the right side of the work surface, keep air moving so you

stay refreshed. Each fan has its own on/o switch; air ow direction is adjusted manually.

Footrest – Put your feet up!

Let’s Start with Your Chair

Choose a chair that reclines back and supports you comfortably when sitting. Scoot all the way in so you can view the monitors

better and your arms are supported by the work surface. We recommend our Verté Chair, Part Number 904BK.

Homing the Table

Homing the table's electric lift system is required each time the table powers up, either after installation or after being shut o.

Leave CT15 powered on except when moving the table.

First, turn the table on and wait one minute.

Using the height adjustment button on the keypad, lower the table to its lowest position until it stops, then hold the button

down for 5 seconds. You will feel the work surface settle gently into place.

Using the tilt adjustment button on the keypad, tilt the table to horizontal until it stops, then hold the button down for 5

seconds. You will feel the work surface settle gently into place.

Home the Anthro Monitor Control System. Using the monitor depth adjustment button, move the monitors all the way back

until they stop, then hold the button down for 5 seconds. No homing is necessary for the height adjustment of the monitors.

Adjusting Your Table Height

It’s vital to vary your position as much as possible throughout the day. So Carl’s Table has a motorized height adjustment from

28" to 48" and you can work sitting or standing with just the touch of a button. The height adjustment button is located on the

keypad on the right side of the work surface.

Changing Your Table Angle

Orthopedic surgeons and other work injury experts say a 90° angle in your elbows and knees is best when working at a desk.

And Carl’s Table lets you electronically tilt the main work surface up to 15° so you can maintain this healthy position even as you

recline.

300-5642-00 rev. C

• /

Programmable Presets

Program your preferred height and tilt positions right into the table! Carl's Table CT15 has 100 programmable presets. The preset

display indicates which setting is active.

To preset a table position:

1) Move the table to the desired height and tilt position.

2) Enter the two-digit number you want to record.

3) Press and hold down the "SET" button for 5 seconds. The display number will ash until the table has recorded the setting.

To position the table to your preset:

1) Enter your two-digit number on the keypad.

2) Press and hold the "GO" button until the table reaches the stored position. The table will stop moving if you stop pressing

the "GO" button.

NOTE: If the red light on the Comfort Control interface is illuminated, the table will not move because one of the safety switches

has been triggered. Read "Troubleshooting" (page 6) or "Some Safety Considerations" below for more information.

Some Safety Considerations

Carl’s Table has a collision avoidance system and will stop the table from moving if it encounters an obstacle while tilting or

moving downwards. Safety sensors are located under the CPU Holder, under the control box, and under the work surface. If a

sensor is triggered, the table will stop moving and the red light on the Comfort Control interface will illuminate.

To avoid injury, stay clear of moving parts while the table is in motion. Do not sit on top of the workstation.

Electrical Requirements

Facilities electrical requirements: dedicated 15 or 20Amp circuit, 120Vac, NEMA 5-15R receptacle.

Power Draw

Power draw: Parasitic

Conditions:

• Lights o

• No computer equipment con-

nected to the table

• No table movement

Power draw:

• Amps: 179mA

• Watts: 8.835

• VA: 21.73

• PF: .407

Power draw: Idle

Conditions:

• All lights on full brightness

• Both fans on

• No computer equipment

connected to the table

• No table movement

Power draw:

• Amps: 464.2mA

• Watts: 47.54

• VA: 56.29

• PF: .844

Power draw: Worst case

Conditions:

• All lights on full brightness

• Both fans on

• No computer equipment con-

nected to the table

• Worst case with table and tilt mov-

ing

Power draw:

• Amps: 3.01

• Watts: 292.90

• VA: 361.1

• PF: .811

300-5642-00 rev. C

• /

Adjusting the Height and Depth of the Anthro Monitor Control System®

The Anthro Monitor Control System electronically adjusts the height and depth of the entire monitor bar. Use the buttons on the

keypad to adjust the settings. You can also adjust the tilt of each monitor manually.

Adjusting Your Lighting

Carl’s Table comes with four lights: two that provide the ambient light on the back panel and two task lights on exible gooseneck

arms to illuminate the work surface. Lights are controlled manually using the knobs on the left side of the table.

Using Your Footrest

If you’re working standing up, you can swing out this footrest to alleviate pressure on your lower back. When you’re done, just

swing it back towards the table leg.

Relocating Carl's Table

If you'd like to relocate your Carl's Table, please contact us for assistance! Relocating the table without Anthro or our authorized

agent will void the warranty.

Installing Your Equipment

Only your IT personnel can install your hardware onto Carl's Table. Use the instructions that are included with those components.

300-5642-00 rev. C

• /

TROUBLE-SHOOTING GUIDE

Having a little trouble making Carl's Table behave? Try these simple steps. If you're still having trouble, please give us a call and we'll work with you to

make it right.

The Table Won't Go Down or Tilt

If your table won’t go down or tilt, it could be that one of the safety stops has been triggered by contact with an obstacle. When this happens, the Safety

Light on the Comfort Control interface will illuminate. Check these locations for obstacles:

Under the coee surface

Under the keyboard surface

Under the control box

Under both CPU mounting brackets

The Table Won't Go Up

If the table will not go up, home the table's legs for both height and tilt following the "Homing the Table" procedures on page 3.

The Table Won't Tilt

If the table will not tilt forward, home the table's legs for both height and tilt following the "Homing the Table" procedures on page 3.

The Anthro Monitor Control System Won't Move

If the monitors will not move forward but will move backward, home the Anthro Monitor Control System following the "Homing the Table" procedures on

page 3. If the monitors will not move forward or backward, let the system rest for 30 minutes and try again.

I Need to Replace a Bulb

The back lights use T8 bulbs and are readily available at hardware stores. The task lights use LED lights that are long-lasting and typically won't need to

be replaced.

The Table Isn't Receiving Power

If Carl's Table isn't receiving power (the lights aren't working or the table won't move or equipment plugged into the table's outlets do not receive

power), rst run through this check-list:

Is main power on? The Power Switch is located on the right side of the Control Box under the keyboard surface. Make

sure the light on the switch is lit.

Is the circuit breaker tripped? The circuit breaker is located next to the power switch. If it has been tripped, press it in

to reset it.

Is the table plugged into a wall receptacle?

Is the wall receptacle receiving power?

If you've addressed each of these and the table still doesn't work properly, please contact us at 800.325.3841.

Cleaning the Keyboard Surface

The main surface of your Carl's Table comes with a polyester micro ber pad that is stain resistant. Most stains can be removed with water and mild

detergent. Replacement pads are available for purchase.

300-5642-00 rev. C

• /

All trademarks are the property of their respective companies.

Anthro is a registered trademark and brand of Ergotron Inc.

Anthro-DNA is a trademark of Ergotron Inc.

For local customer care phone numbers visit: http://contact.ergotron.com

For Service visit: www.ergotron.com

For Warranty visit: www.ergotron.com/warranty

Inhaltsverzeichnis

Andere Ergotron Inneneinrichtung Handbücher

Ergotron

Ergotron LearnFit 24-481-003 Bedienungsanleitung

Ergotron

Ergotron Styleview Vertical Lift LCD Monitor Abmessungen

Ergotron

Ergotron Glide Upgrade Bedienungsanleitung

Ergotron

Ergotron WORKFIT-DL Bedienungsanleitung

Ergotron

Ergotron 97-540-053 Bedienungsanleitung

Ergotron

Ergotron WORKFIT Standing Desk Converter Bedienungsanleitung

Ergotron

Ergotron SV10 Bedienungsanleitung

Ergotron

Ergotron 19610 Bedienungsanleitung

Ergotron

Ergotron 72” AnthroBench II Bedienungsanleitung

Ergotron

Ergotron WorkFit-A, Single LCD Mount, LD Bedienungsanleitung

Ergotron

Ergotron TeachWell LCD Bedienungsanleitung

Ergotron

Ergotron 48" Bench II Bedienungsanleitung

Ergotron

Ergotron WorkFit-D Bedienungsanleitung

Ergotron

Ergotron LearnFit 24-756-003 Bedienungsanleitung

Ergotron

Ergotron Modesty Panel Bedienungsanleitung

Ergotron

Ergotron Projector Shelf for TeachWell Bedienungsanleitung

Ergotron

Ergotron WorkFit-TLE Bedienungsanleitung

Ergotron

Ergotron Zido ZGBCG Bedienungsanleitung

Ergotron

Ergotron LX Sit-Stand Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Bedienungsanleitung

Ergotron

Ergotron Neo-Flex Notebook PC Stand Bedienungsanleitung

Ergotron

Ergotron Yes 20 Bedienungsanleitung

Ergotron

Ergotron Zido ZAH25CG/CG4 Bedienungsanleitung

Ergotron

Ergotron Zido 2-drawer Enclosure Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung