Eureka 4670 Series Bedienungsanleitung

Upright Vacuum Cleaner

Owner’s Guide

4670 Series

Household Type

IMPORTANT

Do not return this

product to the store.

For assembly problems or

questions contact: Eureka’s

Customer Service Division toll

free at 1-800-282-2886*, 7 a.m.

to 8 p.m., Central Standard

Time, Monday through

Saturday.

For replacement of broken

or missing items to be

shipped direct to you, call

1-800-438-7352*, 8 a.m. to

4:45 p.m., Central Standard

Time, Monday through Friday.

*En Mexico llame al 5670-6169

Index

Important Safeguards ........... 2

Service Information............... 4

Assembly ........................... 5-6

Use........................................ 7

Thermal Cut Off ..............4 & 7

Accessories........................... 8

Dirt Alert................................ 9

Brush Roll ........................... 10

Brush Roll Belt ............... 10-11

Dust Bag ........................ 11-12

Hose Blockage............... 13-14

Filters .................................. 15

HEPA Filter.......................... 15

Light Bulb ............................ 16

Problem Solving.................. 18

Customer Order Form......... 19

Warranty.............................. 21

www.eureka.com

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not use outdoors or on wet surfaces.

•Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and

before servicing.

•Do not allow to be used as a toy. Close attention is necessary when used by or near children.

•Use only as described in this manual. Use only manufacturer’s recommended attachments.

•Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left

outdoors, or dropped into water, return it to a service center before using.

•Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do

not run vacuum cleaner over cord. Keep cord away from heated surfaces.

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Turn off all controls before unplugging.

•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

•Do not handle plug or vacuum cleaner with wet hands.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that

may reduce airflow.

•This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing, fingers, and all parts of

body away from openings and moving parts.

•Do not place cleaner on furniture or stairs as the brush roll may cause damage. Place cleaner on floor with the handle in

storage position while using attachments.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

•Do not use without dust bag in place.

•Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive

belt.

•Use extra care when cleaning on stairs.

•Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.

•Store your cleaner indoors in a cool, dry area.

•Keep your work area well lighted.

•Unplug electrical appliances before vacuuming them.

SAVE THESE INSTRUCTIONS

CONSEILS DE SÉCURITÉ

Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent être observées, incluant les suivantes:

LISEZ TOUTES LES INSTRUCTIONSAVANT D’UTILISER VOTRE ASPIRATEUR.

AVERTISSEMENT

Pour réduire le risque de feu, de choc électrique, ou de blessure:

•Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.

•Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou avant le nettoyage ou l’entretien.

•Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire lorsque utilisé par ou prés d’un

enfant.

•Suivezlesrecommandationsd’utilisation de cemanuel. Utilisezuniquementlesaccessoires recommandés parlefabriquant.

•Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne pas comme il le devrait, s’il a été

échappé, s’il est endommagé, s’il a été laissé à l’extérieur ou échappé dans l’eau, retournez-le à un centre de service

avant d’utiliser.

•Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de poignée. Ne pas fermer une porte sur

le cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le

cordon à distance des surfaces chauffantes.

•Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour transporter le courant.

•Fermer tous les contrôles avant de débrancher.

•Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le cordon.

•Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.

•Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées; assurez-vous qu’elles soient

dégagées de poussière, mousse, cheveux ou toute autre chose qui pourrait réduire le passage de l’air.

•Cet aspirateur créé de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin

des cheveux, du linge, des doigts et de toute partie du corps.

•Ne pas mettre l’aspirateur sur les meubles ou sur les escaliers car le rouleau-brosse peut faire des dommages. Placer

l’aspirateur sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage.

•Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou cendres chaudes.

•N’utilisez pas sans le sac de poussière en place.

•Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour prévenir des brûlures, évitez de

touché la poulie du courroie lorsque vous réparez la courroie.

•Portez une attention particulière lorsque vous nettoyez les escaliers.

•Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l’essence: Ne pas utiliser dans les

endroits où ces liquides pourraient être présents.

•Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.

•Maintenez un bon éclairage à l’endroit où vous travaillez.

•Débrancher les appareils électrique avant de les balayer.

CONSERVEZ CES INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit

in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install the proper outlet. Do not change the plug in any way.

Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus large).

Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,

retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un

électricien qualifié. Ne pas modifier la fiche.

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles.Avoid picking up hard or sharp objects with the cleaner to prevent

bag tears, hose clogs, and fan blade breakage with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll

free number for the nearest Eureka Authorized Warranty Station. You should know the model, type and serial numbers

when you call:

USA: 1-800-282-2886

Mexico: 5670-6169

Canada: 1-800-282-2886

If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701,

USA. In Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited

Warranty for complete service information.

DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.

Rating Plate

The model, type, and serial numbers are indicated on the

rating plate located on the underneath side of the cleaner.

Forprompt and complete service information,always refer

to these numbers when inquiring about service.

Model & Type__________________________

Serial No. _____________________________

MODEL TYPE SERIAL NO.

VOLTS AMPS. HERTZ

SERVICE INFORMATION: 1-800-282-2886

THE EUREKA COMPANY

BLOOMINGTON, ILLINOIS 61701

Thermal Cut Off

This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly

shuts off, push the switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such as

a full bag, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before

attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner still

does not run, then take it to a Eureka Authorized Service Center for repair.

HOW TO ASSEMBLE

CAUTION: Assemble the cleaner before using.

CAUTION: Moving parts, stay clear of brush roll when plugging in.

NOTE: Features may vary by model yet all parts assemble the same.

Step B Attach Handle

CAUTION: Do not catch cord under handle.

Step A Attach Hose

1. To attach hose, insert the hose adapter into the bag

compartment tube hole.

Bag Compartment

Tube Hole

Hose Adapter

2. From rear of cleaner, align handle with groove and

slide onto cleaner. If necessary, use thumb and finger

pressure to slide handle into position.

3. Attach handle withtwo 5/8inchscrews inthe assembly

packet. Use either a slotted or Phillips®head

screwdriver.

4. Lift up on the hose adapter to be sure it is secured.

10. Place front cover by aligning tabs at bottom of front

cover into slots on cleaner. Pivot front cover toward

cleaner and push firmly, gripping at the top of the

bag cover, until latch is secure.

Groove

Push to

latch

Push

Step C Install Dust Bag (Some models may

have bag installed.)

5. Fold sides on new paper bag below bag collar.

6. Align bag collar hole and notch with hose tube.

7. Place rear of bag collar on ledges. Push back and

rotate upward until firmly in place.

8. Make sure collar snaps into position and hose tube

is securely inserted into bag collar hole.Tuck bag

into bottom and along sides.

9. Align front cover tabs and close cover. Make sure

paper bag is not caught under the front cover.

Step D Attach Bag Cover

{

,yz{|

Bag

Side

Bag

Collar 5

{

,yz{|

8. Remove front cover by pulling out on the front cover

latch and lifting the front cover upward and out.

9. Check to be sure the paper bag collar is secure with

the hose adapter inside the paper bag collar.

10. Replace front bag cover.

11. You will find your cord retainer on the handle above

the upper cord hook. Firmly push the electrical cord

down into the cord retainer. This will place the cord

out of the way the next time you vacuum.

12. Next wind the cord around the two cord hooks on

the left side of cleaner.

NOTE: For easier access to bag compartment, when

you store the electrical cord use a figure 8

pattern.

13. Secure the plug to the cord to prevent unwinding.

Hose

Adapter

Cord

Hook

Step G Store Electrical Cord

Step E Store Hose and Accessories Step F Check Disposable Dust Bag

Combination

Tool

Crevice

Tool

Hook

Hose

Retainer

Cord

Hook

Cord

Retainer

Extension

Wand or

Wands

Carrying

Handle

HEPA Filter

(on some

models)

Optional Dusting Brush and

Upholstery Tool can be

stored in place of the

combination tool on handle

pegs.

Handle

Pegs

Paper Bag Collar

Front Cover

Latch

Clean

Under

Use

Handle

Release

HOW TO USE

Theuprightvacuumcleaner designallowsuseon multipletypes

ofcarpeting and on upholstery orbare floors withattachments.

When using the attachment tools, place the handle in the

upright position. Do not place cleaner on furniture or steps

as the brush roll may cause damage.

1. Adjust cleaner height setting knob to lowest position for

maximum cleaning. Adjust to a higher setting to make

pushing easier. For ease in moving the adjustment knob,

place handle in operating position and tilt cleaner back to

remove weight from front wheels.

2. Unwind all of the electrical cord. Located above the cord

hookis the cord retainer. Firmly push the electriccord down

into the cord retainer. Using the cord retainer will keep the

electric cord up, out of the way while vacuuming.

3. Plug electrical cord into outlet.

4. Step on handle release. Pull handle back to a comfortable

position.

5. Push On or Off power switch.

Store or

Use Attachments

4Handle

Release

5ON/OFF

Thermal Cut Off

This cleaner has a special thermostat that protects the

cleaner in case of motor overheating. If the cleaner

suddenly turns off, follow this procedure:

1. Push on/off pedal once.

2. Unplug cleaner.

3. Check for source of overheating problem (i.e. full bag,

clogged hose or clogged filter).

4. If a full bag, clogged hose or clogged filter is found,

replace the bag, unclog the hose or replace the filters.

5. Wait at least 30 minutes before attempting to reuse the

cleaner.

6. After 30 minute cool down period, plug the cleaner in

and push the switch pedal. The cleaner should turn on.

7. Ifthe cleanerstill doesnot operate,take it toany Eureka

Authorized Service Center for repair.

Cord Retainer

LOW HIGH

Cleaner Height Setting

WARNING: Avoid injury. Keep loose clothing, hair,fingers,

and all other parts of body away from any

moving part (such as the revolving brush).

Turn off the switch and unplug the cleaner

before changing the cleaner height setting.

Thefront ofthe cleanerhas anadjustment thatraises orlowers

thecleanerbase to matchthetype ofcarpet.With

the cleaner cord unplugged, set the adjustment

to lowest setting for maximum cleaning. If the

cleaner is difficult to push, move adjustment to

next highest setting until cleaner is comfortable

to push. The brush roll must reach the carpet for

effective cleaning.

NOTE: For ease in moving the adjustment knob, place

handle in operating position and tilt cleaner back

to remove weight from front wheels.

NOTE: When handle is in upright position, brush roll is

lifted off carpet. This is normal. Height adjustment

will not change brush roll level until the cleaner’s

handle is moved into the operating position.

How To Use Accessories

NOTE: Do not place cleaner on furniture or

steps as the brush roll may cause

damage. Place cleaner on floor with

the handle in storage position while

using accessories.

Crevice Tool

Upholstery

Side

Combination Toolgives two types of cleaning tools. (On some

models.)

•Use brush side to dust furniture, blinds, books, lamps, shelves.

•Use upholstery side for curtains, draperies, cushions, fabrics.

Depending on which cleaner you purchased, you

can have any combination of the following

accessories.

1. Remove hose from rear of cleaner.

2. Place desired accessory onto end of hose.

•Turn ridge end to center. •Push wands together.

•Pull apart.

Dusting

Side

•Grasp both wands near ridges.

Nested extension Wands to add reach.

Extension Wands (Some models use 1 wand)

Dusting Brush is for furniture, blinds, books, lamp shades,

shelves. (On some models.)

Upholstery Nozzle is for curtains, draperies, cushions,

fabrics. (On some models.)

Dusting Brush

Upholstery

Nozzle

Crevice Tool cleans corners, baseboards, between cushions.

Always work with the cleaner below you,

pulling hose from side of cleaner;

not

the back

or the front of the cleaner.

Maintenance of Dirt Alert Feature (On some models)

The dirt alert sensor uses infra-red technology to indicate whether or not floors are clean. When debris breaks the light

beam, the red light comes on indicating additional cleaning is needed in this area. If there is no break in the light beam, the

floor is clean and no light will come on.

When using your new vacuum you may be cleaning deep down hidden dirt missed by your old vacuum causing the light to

stay red longer. With frequent cleaning, after the first few times you use your new Eureka vacuum, the red light should go

on less.

Thered light indicatesdirt, dust, etc. is stillbeing removed

from the area being cleaned.

NOTE: The dirt alert feature is not intended to be used for above the floor cleaning with attachments.

To check if dirt sensor is working properly.

1. While the red light is on, tip the vacuum backwards on rear

wheels, lifting the brush roll off the carpet a couple of inches.

2. After a few seconds the red light should turn off.

HINT: New carpeting has loose carpet fibers which will trip

the red light sensor beam.

How to Check the Dirt Alert Sensors

HOW TO MAINTAIN

The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag,

belt, and brush roll often.

Brush Roll

The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues

brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length,

hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll.

Brush Roll Belt

The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is

in good condition. Replace the belt if it stretches, cracks or loses tension. Cut away any hair or threads wound around the

brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly.

How To Replace Brush Roll Belt

NOTE: Turn off the switch and unplug the electrical cord before replacing belt. Belt pulleys can become hot during

normal use. To prevent injury, avoid touching the motor pulley when checking the belt.

1. Lower handle to floor to change belt.

2. Loosen, but do not remove, two screws to release

hood. Lift hood to remove.

3. Lift left end of brush roll.

4. Remove and discard belt.

Motor

Pulley

Belt

Brush

Roll

Inhaltsverzeichnis

Andere Eureka Staubsauger Handbücher

Eureka

Eureka NEC3MC Bedienungsanleitung

Eureka

Eureka SC780 Series Bedienungsanleitung

Eureka

Eureka 160 Series Bedienungsanleitung

Eureka

Eureka NEU610 Series Bedienungsanleitung

Eureka

Eureka 2900 Series Bedienungsanleitung

Eureka

Eureka 178A Bedienungsanleitung

Eureka

Eureka 470 Series Bedienungsanleitung

Eureka

Eureka 160 Series Bedienungsanleitung

Eureka

Eureka 7600 Series Bedienungsanleitung

Eureka

Eureka 410 SERIES Bedienungsanleitung

Eureka

Eureka AS3350 series Bedienungsanleitung

Eureka

Eureka Optima 430 Series Bedienungsanleitung

Eureka

Eureka AS3020 series Bedienungsanleitung

Eureka

Eureka 970-975 Series Bedienungsanleitung

Eureka

Eureka 4770 Series Bedienungsanleitung

Eureka

Eureka 6980 Series Bedienungsanleitung

Eureka

Eureka ReadyForce 900A Bedienungsanleitung

Eureka

Eureka 410 SERIES Bedienungsanleitung

Eureka

Eureka 4650 Series Bedienungsanleitung

Eureka

Eureka AS5200 Series Bedienungsanleitung

Eureka

Eureka 910 Series Bedienungsanleitung

Eureka

Eureka AS1000 Series Bedienungsanleitung

Eureka

Eureka Swan MULTI-FORCE Bedienungsanleitung

Eureka

Eureka PowerSpeed NEU202C Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung