EverFocus PowerPlex EDR1600 Service-Handbuch

Administrator’sGuideandOperatingInstructions

WARNING

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: This equipment has been tested and found to comply with the

limits for a Class “A” digital device, pursuant to part 15 of the FCC Rule

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause interference to radio communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the users will be required to correct

the interference at their own expense.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

This Class A digital apparatus meets all requirements of the Canadian

Interference Causing Equipment Regulations.

Notice:

The information in this manual was current when published. The manufacturer reserves

the right to revise and improve its products. All specifications are therefore subject to

change without notice.

Administrator’sGuideandOperatingInstructions

PRECAUTIONS

nRefer all work related to the installation of this product to qualified

service personnel or system installers.

nDo not block the ventilation opening or slots on the cover.

nDo not drop metallic parts through slots.

This could permanently damage the appliance. Turn the power off

immediately and contact qualified service personnel for service.

nDo not attempt to disassemble the appliance.

To prevent electric shock, do not remove screws or covers. There are

no user-serviceable parts inside. Contact qualified service personnel

for maintenance.

nHandle the appliance with care.

Do not strike or shake, as this may damage the appliance.

nDo not expose the appliance to water or moisture, nor try to operate it

in wet areas.

Do take immediate action if the appliance becomes wet. Turn the

power off and refer servicing to qualified service personnel.

Moisture may damage the appliance and also cause electric shock.

nDo not use strong or abrasive detergents when cleaning the appliance

body.

Use a dry cloth to clean the appliance when it is dirty. When the dirt

is hard to remove, use a mild detergent and wipe gently.

nDo not overload outlets and extension cords as this may result in a risk

of fire or electric shock.

nDo not operate the appliance beyond its specified temperature,

humidity or power source ratings.

Do not use the appliance in an extreme environment where high

temperature or high humidity exists.

Use the appliance at temperature within 0oC ~ +45oC and a humidity

below 90%. The input power source for this appliance is 115V AC or

230V AC, 50Hz –60Hz.

Administrator’sGuideandOperatingInstructions

iii

TableofContents

1. Product Overview ………………….……………………….……...

1.1 Features…………………..……….…………..…………………...

1.2 Technical Overview…….….…….………………………….……..

2. Front & Rear Panels ….…….……………………………….…….

3. System Installation…….…….……………………………….……

3.1 Before Installation…….……….…………………………….…….

3.2 Basic Connections…………….…………………………….……..

3.3 Optional Connections…………..…………………………….……

4. Main Screen …………………………………………..……….…...

4.1 View Display & Print Image………………………………………

5. Basic Operations & Log Display ……………………..………..….

5.1 Version Display……………………………..…………….…….…

5.2 Alarm Message Display……………………...……………………

6. Setup (Administrator) ………………..….………………………...

6.1 Time Type Setup…………………..…….………………………...

6.2 Day Type Setup……………………………………………………

6.3 Calendar Setup…………………..…………………….…………..

6.4 Alarm Action Setup………………………………………………..

6.5 Motion Action Setup……………..…………………….………….

6.6 Video Loss Action Setup…………………………………………..

6.7 Hard Disks Full Action Setup ……………………………………..

6.8Camera Setup…………...…………………………………………

6.9Alarm In Setup…………..……………………………….………..

6.10 Alarm Out Setup……………..…………………………………..

6.11Display Sequence Setup……………………..………….………..

6.12Display Page Setup……………………………………………….

6.13Motion Setup……………………………………………………..

6.14 Password Setup…………………………………..……….……...

6.15System Configurations………...………...…………….…………

6.16 Audio Setup………………………………………………………

6.17 Set Call Monitor………………………………………………….

7. PTZ Control Functions ……………………………………………

8. Day/Time Setup (Administrator) …………………………………

9. Image Playback and Archive (Administrator, Supervisor)……

9.1 Select HDD & Range Dialog Box…………………………………

10. Remote Control..…………………………………..……….……...

10.1 Connecting the Remote PC and Server……………………………

10.2 Remote View………………………………………………………

11. Remote View from i-mode …………………………………………

12. NoteFor “2x/fps” and Some Limitations ………………………...

Appendix A –Specifications

Appendix B –Time Lapse Mode Recording Time

Appendix C –Simulated Keyboard

Appendix D –Q & A

Administrator’sGuideandOperatingInstructions

1.ProductOverview

The PowerPlex EDR1600 is a state-of-the-art digital video recorder

that brings unparalleled video surveillance, recording and playback

to the CCTV systems. With parallel processing architecture, high

performance video engine, and intelligent recording algorithms,

triplex operation can be easily achieved without sacrificing the

increasing demands of performance, reliability, and availability in the

CCTV industry.

1.1Features

nConnects up to 16 color or B/W cameras

nReal triplex operation: Simultaneous recording, live & playback

nBuilt-in MPEG-1 and JPEG compression/decompression with

configurable video quality

nIntelligent motion detection with programmable area and sensitivity

for each camera

nPowerful alarm processor with configurable triggering conditions and

reactions

nEvent recording, time-lapse recording or both

nPre alarm / post alarm recording for alarm, motion, and video loss

with adjustable frame rate for different time modes and cameras

nUp to two internal Hard Disks

nConnect up to two external Hard Disk Arrays (Max. 8 Hard Disks per

set) to enhance the storage capacity

nHot swappable hard disks for highest surveillance availability

nNon-editable video data with data loss at 1-second level (caused by

bad sectors in Hard Disks after recording)

nUnique digital watermark

nVideo storage (in .MPG or .MOV format) to floppy disks, ZIP drives,

CD-RW, DVD RAM etc.

nVersatile display formats: full-screen, 4, 7, 9, 10, 13, and 16 video

windows

nAlarm history log for video loss, motion, & alarm input

nMulti-level password to ensure high degree of security

nRecording rate: up to 60 fps for NTSC, 50 fps for PAL

nPlayback rate: up to 30 fps for NTSC, 25 fps for PAL

nIndependent record & playback.

nBuilt-in flash memory, power on and off data protection

nBuilt-in 16x8 video matrix

nBuilt-in Watch Dog Timer

nGraphics user interface with built-in real-time kernel, Windows OS

not required

nMulti-Lingual support (English, Chinese, German, Japanese, Spanish,

Italian, Finnish, Swedish, French, Dutch and Portuguese.)

nRemote surveillance and playback through WEB browser (such as IE

or Netscape) or i-mode mobile phone

nRemote alarm notification

nTime Stamp function for recording image

nPrinter supported

Administrator’sGuideandOperatingInstructions

1.2TechnicalOverview

1.2.1VideoInput andOutput

The digital video recorder is designed to support either NTSC/EIA or

PAL/CCIR standard. To make the auto detection of video standard

work, at least one camera must be connected to the video input. The

product features video camera inputs with a passive looping output

for each. Camera input impedance termination is set independently

for each camera automatically. Synchronizing or phasing cameras

is not required to achieve the frame rate of 30 fps for NTSC/EIA

or 25 fps for PAL/CCIR.

Video surveillance and playback is supported by a VGA monitor

connection and optional main monitor connections for composite

formats. The main monitor displays the selected cameras in any

available display format. Another composite video output is

provided for call monitor that displays any alarm images or the live

images of all the installed cameras sequentially.

1.2.2VideoProcessing

The video processor controls the switching of the built-in video

matrix according to the system configurations. The video encoder

analyzes the video signal from the cameras, and encodes the

incoming pictures in a JPEG format or MPEG-1 format that is

digitized and smaller in size at 30 fps for NTSC/EIA or 25 fps for

PAL/CCIR. During video playback, the video decoder decodes the

digitized format, and displays the decoded pictures on the VGA

monitor screen or TV monitor screen.

1.2.3VideoStorageandRetrieval

The encoded pictures are stored in the hard disks, with the stored

frame rate for each camera set by the administrator. If any event

(Alarm, Motion, or Video Loss) occurs, all the encoded pictures for

the correspondent camera for the preset pre-record duration will be

saved to the hard disk, and the recording rate for that camera will be

changed to its alarm recording rate afterwards for the preset

post-record duration. When the recording reaches the end of the

recording hard disk, the system will automatically switch to the next

available hard disk and record from the beginning of that hard disk.

Administrator’sGuideandOperatingInstructions

During video playback, the selected pictures can be saved to floppy

disk, ZIP disk, CD-RW, DVD RAM etc. in .MPG format for MPEG-1

encoded video or .MOV format for JPEG encoded video.

For Time-Lapse Mode Recording Time, please refer to Appendix B.

1.2.4MotionDetection

The digital video recorder continuously monitors all camera inputs

for motion. When motion is detected, the system reacts according to

the motion action set by the administrator, which includes: increasing

the recording frame rate, sounding the buzzer, triggering the alarm

output, logging the event, etc. Motion detection options for

different time types can be set for each camera input using a 16

(width) by 12 (height) target overlay. You can also enable or disable

motion alarms for different time types. However, the recording

frame rate is NOT influenced by motion detection for the digital

video recorder.

1.2.5VideoDisplay

The VGA monitor and main TV monitor display either live camera

pictures or pictures from hard disks. The display resolution is

640x480 for NTSC or 800x600 for PAL. As many as 16 million

colors can be displayed in the following screen formats: full screen, 4,

7, 9, 10, 13 and 16 windows. All the main displays are window

based look and feel for ease of user operations.

The call monitor displays full screen images of cameras associated

with alarms or images from the installed cameras sequentially. It is

based on switched analog camera input.

1.2.6VideoPlayback

The user can select a previously recorded hard disk to review the

recorded video. Displaying of the recorded video is composed of

decoding the JPEG or MPEG-1 encoded video automatically and

multiplexing each camera video to its designated video window.

With the coded data that was inserted into each recorded picture, the

digital video recorder can reconstruct each camera’s tag name, status,

date, and time information automatically. The image can be

displayed in any multi-window format on the VGA monitor and/or

TV monitor, just like in live video mode.

Administrator’sGuideandOperatingInstructions

1.2.7ExpandableIDEHard DiskArchitecture

All the other HDD-based digital video recorders support only 1-4

hard disks. If those recorders do support more hard disks, they

usually use RAID (Redundant Arrays of Independent Disks) or SCSI

disks, which are very expensive. With the Expandable IDE Hard

Disk Architecture, the EDR1600 can support up to 18 pieces of IDE

hard disks that are hot swappable. With 80 GB of storage per hard

disk, the system storage is more than 1400 GB and virtually

unlimited –no more redundant backup required.

1.2.8Non-editableRecordedImages

The retrieved images are saved as .MPG files or .MOV files, which

can be played by Windows Media Player or QuickTime. Therefore,

the video editing packages can be edited, just like the recorded

images in the other digital video recorders. However, the recorded

images in the hard disks can not editable. Therefore, the recorded

images are guaranteed to be the original images.

Administrator’sGuideandOperatingInstructions

2.Front&RearPanels

The following is a brief overview of the front panel and rear panel of

EDR1600.

Rear Panel

1. Power Switch from Rear Panel

2. Power Selector Switch: 115V AC or 230V AC selector switch.

Warning: To avoid damaging the system, set this switch before

plugging in the power plug.

Use a screwdriver to set the switch to the correct position so that the

number shown is the same as the local AC voltage.

3. Power Socket: Accepts 115V AC or 230V AC power source.

(Power Selector at AC 115V: 100-120V AC)

(Power Selector at AC 230V: 200-260V AC)

4. Mouse Connector: Connects to the PS2 mouse. The mouse must be

connected at system startup.

5. Keyboard Connector: Connects to the keyboard (optional).

Administrator’sGuideandOperatingInstructions

6. 2 USB Connectors: Connect to USB port devices, e.g. CD-RW, DVD

RAM, printer, ZIP.

7. RS-232 Connector: Com 1, connects to modem.

8. Printer Port Connector: Connects to printer port devices (e.g.

ZIP/printer port).

9. RS-232 Connector: Com 2, connects to PTZ camera.

10. Audio Out: Connect to speakers or other audio out devices.

11. Audio In: Connect to microphone or other audio in devices.

12. VGA Monitor Output.

13. Camera 16 Video Input: BNC connector for Camera 16.

14. Main Monitor Output: BNC connector for Main TV monitor

15. Call Monitor Output: BNC connector for Call TV monitor.

16. Camera 16 Video Output: BNC connector for looping camera video

from the corresponding camera input.

17. LAN Connector Outlet: Ethernet 10/100 Mb base-T.

18. External Hard Disk Connector: Connects to External Hard Disk

Array EDA800.

19. Cooling Fan: Cooling fan of internal Switching Power Supply.

20. Camera 1 Video Input: BNC connector for Camera 1.

21. Alarm In 1-8: Connects to alarm inputs 1-8 & 1 common ground.

22. Camera 1 Video Output: BNC connector for looping camera video

from the corresponding camera input.

23. Alarm In 9-16: Connects to alarm inputs 9-16 & 1 common ground.

24. Alarm In 17-24: Connects to alarm inputs 17-24 & 1 common

ground.

25. Alarm Out: Connects to 4 Normally Closed alarm outputs (1-4), 4

Normally Open alarm outputs (5-8) & 1 common ground.

Administrator’sGuideandOperatingInstructions

Front Panel

26. Hard Disk Trays: Hard disk holders for HDD#1 (upper tray) and

HDD#2 (lower tray). (Note1.2)

Please make sure to set HDD#1 as master and HDD#2 as slave.

The settings should be described on the hard disk itself or in the

manual that comes with the hard disk.

27. Floppy Drive: 3.5”, 1.44MB.

28. LEDs, Reset Button and Power Switch: LEDs for power and HDD

indication, Reset Button to reset the system, and Power Switch to

power on/off the system.

29. Dust Filter for Front Cooling Fan.

Note 1: For HDD#2 to be accessible, make sure HDD#2 exists at system power up

or HDD#1 power up. Afterwards, you may swap HDD#2 anytime except

when it's recording. For the other hard disks, there are no limitations for

hot-swap. If it happens that HDD#2 is not accessible, please power off

both HDD#1 and HDD#2, and then power on both of them immediately.

Note 2 : We strongly recommend that you use IBM’s hard disks as HDD#1

(master) because they are consistent and stable for hot-swapping.

Andere Handbücher für PowerPlex EDR1600

Inhaltsverzeichnis

Andere EverFocus DVR Handbücher

EverFocus

EverFocus VANGUARD II 8x4H Bedienungsanleitung

EverFocus

EverFocus ECOR4D Bedienungsanleitung

EverFocus

EverFocus EMV1200 HD Bedienungsanleitung

EverFocus

EverFocus PARAGON 264x1 Bedienungsanleitung

EverFocus

EverFocus ECOR264-4D1 Bedienungsanleitung

EverFocus

EverFocus VANGUARD 16x8H Plus Bedienungsanleitung

EverFocus

EverFocus ECOR264X1 Series Installations- und Betriebshandbuch

EverFocus

EverFocus EDVR16D1/250 Bedienungsanleitung

EverFocus

EverFocus IRONGUARD 16 POE Bedienungsanleitung

EverFocus

EverFocus Paragon960 Bedienungsanleitung

EverFocus

EverFocus ELR-4 Bedienungsanleitung

EverFocus

EverFocus ECOR264-D2 DVR Series Bedienungsanleitung

EverFocus

EverFocus EDR810H Bedienungsanleitung

EverFocus

EverFocus ENR 400 Bedienungsanleitung

EverFocus

EverFocus ENVR8304E-8CH Bedienungsanleitung

EverFocus

EverFocus ECOR264-16X1 Bedienungsanleitung

EverFocus

EverFocus MoniVue System ESN41 Bedienungsanleitung

EverFocus

EverFocus ECOR960 4F2 Bedienungsanleitung

EverFocus

EverFocus eZ.HD ELUX4 Bedienungsanleitung

EverFocus

EverFocus ECOR2 Bedienungsanleitung

EverFocus

EverFocus EDVR SERIES Installationsanleitung

EverFocus

EverFocus EDR810H Bedienungsanleitung

EverFocus

EverFocus EMV401 Bedienungsanleitung

EverFocus

EverFocus Paragon264 Series Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

FSM

FSM Colibri Grande PRO Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung