Federal Signal Corporation Cuda TriOptic 351011F Series Bedienungsanleitung

2562295A

REV. A 1107

Printed in U.S.A.

INSTRUCTION SHEET

FOR

Cuda TriOptic™ MODEL 351011F SERIES

SAFETY MESSAGE TO INSTALLERS AND USERS

People’s lives depend on your safe instal-

lation of our products. It is important to

read, understand and follow all instructions

shipped with the products. In addition, listed

below are some other important safety in-

structions and precautions you should follow:

• To properly install this light, you must

have a good understanding of automo-

tive systems, along with proﬁciency in

the installation and use of safety warning

equipment.

• DO NOT install equipment or route wir-

ing in the deployment path of an air bag.

• When drilling into a vehicle structure,

be sure that both sides of the surface are

clear of anything that could be damaged.

• In order for the light to function prop-

erly, a separate ground connection must

be made. If practical, it should be con-

nected to the negative battery terminal.

At a minimum, it may be attached to a

solid metal body or chassis part that will

provide an effective ground path as long

as the light system is to be used.

• Locate light control so the VEHICLE and

CONTROL can be operated safely under

all driving conditions.

• Do not attempt to activate or deactivate

light control while driving in a hazardous

situation.

• You should frequently inspect the light to

ensure that it is operating properly and

that it is securely attached to the vehicle.

• This product contains high intensity LED

devices. To prevent eye damage, DO NOT

stare into the light beam at close range.

• The light should be frequently inspected

to ensure that it is operating properly

and that it is securely attached to the ve-

hicle.

• File these instructions in a safe place and

refer to them when maintaining and/or

reinstalling the product.

Failure to follow all safety precautions and

instructions may result in property damage, serious

injury, or death to you or others.

I. GENERAL.

The Cuda TriOptic Model 351011F is a LED light head

designed for use in conjunction with all Federal Signal

switch controllers. This light head is designed for mounting

on a vehicle’s interior, exterior or on a motorcycle. The

housing is comprised of an extruded aluminum proﬁle with

a front high-impact polycarbonate lens. The unit is supplied

with mounting hardware and a ﬁve-foot cable. This unit

has an operating temperature range of –30ºC to +65ºC (-

22°F to +149ºF). It may be mounted in the horizontal, or

vertical position with the cable exiting from the rear. The

physical dimensions of this unit are 3.8-inches long, 1.5-

inches wide by 1.75-inches high. End caps and the front

lens cover are compression sealed to the extruded housing

by means of gaskets. The unit also features stainless steel

hex machine screws and keps nuts for the channels on the

top, bottom and rear of the housing. The Cuda TriOptic

is programmed with eight ﬂash patterns selectable by a

control lead without opening the device. The light head

can also be user conﬁgured to be controlled by an external

ﬂashing device.

II. INSTALLATION.

This product is intended for supplemental

warning and for use in conjunction with

an approved primary warning light sys-

tem. Consult local codes and regulations to

determine if the power supply/ light head

combination complies with the horizontal or

vertical mount position desired in your ap-

plication.

When installing equipment inside air bag

equipped vehicles, the installer MUST ensure

that the equipment is installed ONLY in areas

recommended by the vehicle manufacturer.

Failure to observe this warning will reduce

the effectiveness of the air bag, damage the

air bag, or potentially damage or dislodge the

equipment, causing serious injury or death to

you or others.

A. Determine which side of the unit will be attached

to the mounting surface. From a horizontal orientation,

the top, bottom and rear surfaces of the unit are available

for mounting. The top and bottom surfaces each have one

mounting bolt channel and the rear surface has two (see

ﬁgure 1). Choose the mounting channel that best suits your

application.

B. See ﬁgure 1. Locate the opening in the selected

mounting bolt channel and drop in two #8-32 hex head

screws.

Before drilling in ANY part of the vehicle, be sure that both

sides of the mounting surface are clear of parts that could

be damaged; such as brake lines, fuel lines, electrical wiring

or other vital parts.

C. Drill two 3/16” hole as needed for the #8-32

mounting screws. It is recommended that the screws be 2-

3” apart.

D. Secure the unit to the mounting surface using the

supplied keps nuts.

Install the control unit in an adequately ventilated area.

Never install near heater ducts.

After prolonged operation, the unit dissipates heat and

can cause burns. Do not hold the unit in your hands for

extended periods of time. Do not touch the unit during, or

shortly after, operation. Always allow the unit to cool before

handling.

290A5667

#8-32 X 1/2" HEX HEAD

MACHINE SCREW (2)

TOP CHANNEL

(SAME AS BOTTOM)

REAR CHANNELS

OPENING FOR HEX HEAD

MOUNTING SCREW (4)

Figure 1.

-2-

III. ELECTRICAL SPECIFICATIONS AND FEATURES.

NOTE

Powering multiple devices with a common con-

trol lead may cause one or more units to brieﬂy

remain functional after signal power is removed.

For example, due to high input ﬁlter capacitance,

a strobe supply can brieﬂy supply the current

required to operate a low current device such as a

Cuda TriOptic. If necessary, use a relay to isolate

devices with large ﬁlter capacitors. See ﬁgure 2 for

suggested schematic, all components and wires are

user-supplied.

The unit is intended to operate on a 12.8 VDC system.

It includes a jacketed 6 conductor cable. The 6 conductors

are: red (positive), black (negative), green (programming),

yellow (external ﬂash), orange (external ﬂash), and white

(not used). This unit is intended to work in conjunction

with all Federal Signal switch controllers.

A. Flashing Operation.

1. Cut and insulate the orange and yellow wires.

These are not used.

2. Connect the black wire to ground.

3. Using a user supplied 3A fuse connect the red

wire to a positive 12 VDC source.

4. This unit features 8 ﬂash patterns that are

selected by grounding the programming wire (green). The

ﬂash patterns are as follows:

a. Steady On

b. 120 FPM

c. 165 FPM

d. 240 FPM

e. 300 FPM

f. Combo 1:

4 intervals @ 120 FPM

10 intervals @ 300 FPM

g. Combo 2:

2 intervals @ 120 FPM

3 intervals @ 165 FPM

6 intervals @ 240 FPM

3 intervals @ 165 FPM

2 intervals @ 120 FPM

10 intervals @ 300 FPM

h. Combo 3:

1 interactive interval @ 120 FPM

2 intervals @ 120 FPM

6 intervals @ 240 FPM

14 intervals @ 480 FPM

6 intervals @ 240 FPM

2 intervals @ 120 FPM

1 interactive interval @ 120 FPM

After the desired pattern has been selected

connect the programming wire (green) directly to the

positive power wire (red).

The unit is designed to return to the last ﬂash

pattern selected before it was de-energized. For example,

if the unit is de-energized at the seventh ﬂash pattern

and then re-energized, the seventh pattern illuminates.

However, there is a two second delay for the unit to

remember the last ﬂash pattern. So, if the unit is energized

and functioning on the third ﬂash pattern and the unit

is switched to the fourth ﬂash pattern and de-energized

within two seconds, the unit will return to the third ﬂash

pattern when the unit is re-energized.

B. External Flashing Device Operation.

1. For a high side activated ﬂasher, use a user

supplied 3A fuse and connect the red and green wires to

the output control lead on the ﬂasher. Connect the black,

yellow, and orange wires to ground.

2. For a low side activated ﬂasher, use a user

supplied 3A fuse and connect the red and green wires to a

12V source. Connect the orange, black, and yellow wires to

the output control lead on the ﬂasher.

290A5668

CUDATRIOPTIC

+12V

CONTROL LEAD

(12V SIGNAL ACTIVATED)

RELAY

FUSE

STROBE SUPPLY

Figure 2.

SAFETY MESSAGE TO OPERATORS

People’s lives depend on your safe use of our

products.

Listed below are some important safety in-

structions and precautions you should follow:

• Although your warning system is operat-

ing properly, it may not be completely ef-

fective. People may not see or heed your

warning signal. You must recognize this

fact and continue driving cautiously.

• Also, situations may occur which obstruct

your warning signal when natural or

manmade objects are between your vehi-

cle and others, such as: raising your hood

or trunk lid. If these situations occur, be

especially careful.

• This product contains high intensity LED

devices. To prevent eye damage, DO NOT

stare into the light beam at close range.

• At the start of your shift, you should en-

sure that the light is securely attached

and operating properly.

Failure to follow these safety precautions may

result in property damage, serious injury, or death to

you, to passengers, or to others.

RETAIN AND REFER TO THIS MESSAGE

-3-

IV. MAINTENANCE.

A. General.

Crazing (cracking) of lenses will cause

reduced effectiveness of the light. Do not

use cleaning agents (which will cause craz-

ing) such as strong detergents, solvents, or

petroleum products. If crazing of lenses does

occur, reliability of light for emergency sig-

naling purposes may be reduced.

Ordinary cleaning of the plastic lenses can be

accomplished by using mild soap and a soft rag. Should ﬁne

scratches or a haze appear on a lens, they can ordinarily

be removed with a non-abrasive, high-quality, one-step,

automotive paste cleaner/wax and a soft cloth.

B. Replacement Parts.

The unit must not be opened under any

circumstance, failure to adhere to this may result in

moisture entering into the unit causing premature failure.

Please contact the factory if the unit is not functioning

properly.

Manufactured by:

Federal Signal Corporation

Emergency Products Group

2645 Federal Signal Drive

University Park, Illinois 60466

1-800-433-9132

E-mail: [email protected]

-4-

Andere Federal Signal Corporation Beleuchtungsausrüstung Handbücher

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SignalMaster SMLED-PLS-6 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 151XST Series Handbuch

Federal Signal Corporation

Federal Signal Corporation Navigator Lightbar Handbuch

Federal Signal Corporation

Federal Signal Corporation Electraray 225XL Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vitalite 121SLED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MicroPulse SignalMaster Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation LED SIGNALMASTER Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation STREAMLINE LP3M Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation QuadraFlare QL64Z3V-LI Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation G-STR-024-D-C Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Viper SignalMaster Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 371DST Handbuch

Federal Signal Corporation

Federal Signal Corporation AV1-LED Handbuch

Federal Signal Corporation

Federal Signal Corporation Vitalite 121SLED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation NightSpire Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CN SignalMaster Handbuch

Federal Signal Corporation

Federal Signal Corporation ELECTRARAY 225X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Electraray 225 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SM518A-24 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 352012F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation QUADRAFLARE QL97LEDSCENE Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351012F Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung