Federal Signal Corporation NightSpire Bedienungsanleitung

25500704

Rev. A0 0221

Printed in U.S.A.

Installation and Maintenance Instructions

NightSpire™Search Light

Las instrucciones en español comienzan en la página 21.

Pour voir ce manuel en franÇais, allez à www.fedsig.com.

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of tness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Customer Support

Police/Fire-EMS: 800-264-3578 • +1 708 534-3400

Work Truck: 800-824-0254 • +1 708 534-3400

Technical Support 800-433-9132 • +1 708 534-3400

Installation and Maintenance Instructions

Federal Signal www.fedsig.com

Contents

Safety Message to Installers and Service Personnel.....................4

Overview.............................................................................................7

Unpacking ..........................................................................................7

Installation..........................................................................................8

Wiring ...............................................................................................10

Permanently Mounting....................................................................11

Pipe Mounting..................................................................................13

Using Magnetic Mounting ..............................................................13

Setting up the Controller ................................................................14

Operation..........................................................................................17

Cleaning ...........................................................................................18

Getting Technical Support..............................................................18

Getting Repair Service....................................................................19

Ordering Replacement Parts..........................................................19

Returning a Product to Federal Signal..........................................19

Figures

Figure 1 Search light mounted on ange.......................................9

Figure 2 Permanently locking the ange .....................................10

Figure 3 Drilling (Not to scale) ......................................................11

Figure 4 Exploded view of installation .........................................12

Figure 5 Controller .........................................................................16

Tables

Table 1 Product specications.......................................................7

Table 2 Kit Contents ........................................................................8

Table 3 Wire Connections.............................................................10

Table 4 Replacement Parts ...........................................................19

Safety Message to Installers and Service Personnel

NightSpire™Search Light

Federal Signal www.fedsig.com

Safety Message to Installers and Service Personnel

People’s lives depend on your proper installation and servicing

of Federal Signal products. It is important to read and follow all

instructions shipped with this product. In addition, listed below

are some other important safety instructions and precautions

you should follow:

• To properly install or service this equipment, you must have a

good understanding of automotive mechanical and electrical

procedures and systems, along with proﬁciency in the

installation and service of safety warning equipment. Always

refer to the vehicle’s service manuals when performing

equipment installations on a vehicle.

• To be an eective warning device, this product produces

bright light that can be hazardous to your eyesight when

viewed at a close range. Do not stare directly into this

lighting product at a close range, or permanent damage to

your eyesight may occur.

• Do not install the light system in an area that would block,

impair, or blind the driver’s vision. Ensure that the light

system is mounted in a position that is outside the driver’s

ﬁeld of vision so the driver can safely operate the vehicle.

• A light system is a high current system. For the system

to function properly, a separate negative (–) connection

and positive (+) connection must be made. All negative

connections should be connected to the negative battery

terminal, and a suitable fuse should be installed on the

positive battery terminal connection as close to the battery

as possible. Ensure that all wires and fuses are rated

correctly to handle the device and system amperage

requirements.

• Never attempt to install aftermarket equipment that connects

to the vehicle wiring without reviewing a vehicle wiring

diagram available from the vehicle manufacturer. Ensure that

your installation will not aect vehicle operation or mandated

Safety Message to Installers and Service Personnel

Installation and Maintenance Instructions

Federal Signal www.fedsig.com

safety functions or circuits. Always check the vehicle for

proper operation after installation.

• The lighting system components, especially the outer

housing, get hot during operation. Be sure to disconnect

power to the system and allow the system to cool down

before handling any components of the system.

• Do not mount a radio antenna within 18 inches (45.7 cm)

of the lighting system. Placing the antenna too close to

the lighting system could cause the lighting system to

malfunction or be damaged by strong radio ﬁelds. Mounting

the antenna too close to the lighting system may also cause

the radio noise emitted from the lighting system to interfere

with the reception of the radio transmitter and reduce radio

reception.

• Do not attempt to wash any unsealed electrical device while

it is connected to its power source.

• DO NOT connect this system to the vehicle battery until

ALL other electrical connections are made, mounting of

all components is complete, and you have veriﬁed that no

shorts exist. If the wiring is shorted to the vehicle body or

frame, high current conductors can cause hazardous sparks,

resulting in electrical ﬁres or ﬂying molten metal.

• DO NOT install equipment or route wiring (or the plug-in

cord) in the deployment path of an airbag.

• Before drilling into a vehicle structure, ensure that both sides

of the surface are clear of anything that could be damaged.

Remove all burrs from drilled holes. To prevent electrical

shorts, grommet all drilled holes through which wiring

passes. Also, ensure that the mounting screws do not cause

electrical or mechanical damage to the vehicle.

• Because vehicle roof construction and driving conditions

vary, do not drive a vehicle with a magnetically mounted

warning light installed. The light could ﬂy o the vehicle,

causing injury or damage. Repair of damage incurred

Safety Message to Installers and Service Personnel

NightSpire™Search Light

Federal Signal www.fedsig.com

because of ignoring this warning shall be the sole

responsibility of the user.

• Locate the light system controls so the VEHICLE and

CONTROLS can be operated safely under all driving

conditions.

• After installation, test the light system to ensure that it is

operating properly.

• Test all vehicle functions, including horn operation, vehicle

safety functions, and vehicle light systems to ensure proper

operation. Ensure that the installation has not aected the

vehicle operation or changed any vehicle safety function or

circuit.

• Scratched or dull reﬂectors or lenses will reduce the

eectiveness of the lighting system. Avoid heavy pressure

and use of caustic or petroleum-based products when

cleaning the lighting system.

• Replace any optical components that may have been

scratched or crazed during system installation.

• Do not attempt to activate or deactivate the light system

controls while driving in a hazardous situation.

• You should frequently inspect the light system to ensure that

it is operating properly and that it is securely attached to the

vehicle.

• After installation and testing are complete, provide a copy

of these instructions to instructional sta and all operating

personnel.

• File these instructions in a safe place and refer to them when

maintaining and/or reinstalling the product. Failure to follow

all safety precautions and instructions may result in property

damage, serious injury, or death.

Unpacking

Installation and Maintenance Instructions

Federal Signal www.fedsig.com

Overview

The NightSpire™is a remotely adjustable search light with

an adjustable light pattern. It can be rotated horizontally,

360°continuously. It can elevate from 40° down to 90° up. The

light output is continuously adjustable from a 4° spot to a 50°

wide ﬂood.

The wireless remote uses 2 AAA (LR03) batteries and has a

range of approximately 125 feet. The wireless remote can be

programmed for selectable control of up to three dierent

search lights, individually selectable at the remote. There are

two memory buttons available to save preset locations and spot

sizes.

Table 1 Product specications

Nominal Input Voltage 12 Vdc

Input Current 3.0 A

Height Perm Mt: 7.10 inches (18.0 cm)

Mag mt: 6.94 inches (17.6 cm)

Diameter Perm Mt: 6.54 inches (16.6 cm)

Mag Mt: 5.19 inches (13.2 cm)

Weight Perm Mt: 2.4 lb (1.1 kg)

Mag Mt: 2.5 lb (1.1 kg)

Wireless Operating Frequency 2.4 GHz

Unpacking

After unpacking the search light, inspect it for damage that

may have occurred in transit. If there is damage, ﬁle a claim

immediately with the carrier, stating the extent of damage.

Carefully check all envelopes, shipping labels, and tags before

removing or destroying them. If installing a permanent mounted

search light, ensure that the parts listed in Table 2 are included

in the package.

Installation

NightSpire™Search Light

Federal Signal www.fedsig.com

Table 2 Kit Contents

Qty. Description

3 #8 Pan Head Phillips Screw

3 #10 Pan Head Phillips Screw

3 1-3/4-inch #10 Machine Screws

3 7/8-inch #10 Machine Screws

3 #10 Machine Nuts

1 Remote

2 AAA Batteries

Installation

Attaching the Mounting Flange

The mounting ﬂange shipped with the unit is removable. You

can either leave it attached the search light before installation or

attach the ﬂange to the vehicle ﬁrst. If desired, permanently lock

the ﬂange to the base using the three #8 screws provided. See

Figure 1.

DO NOT DRIVE WITHOUT FIRST MOUNTING THE SEARCH

LIGHT TO THE FLANGE: Because vehicle roof construction and

driving conditions vary, do not drive a vehicle if the search light

is not attached to the ange. The light could y o the vehicle,

causing injury or damage. Repair of damage incurred because of

ignoring this warning shall be the sole responsibility of the user.

To attach the mounting ﬂange:

1. Locate the detent on the search light and one of the two

detent notches on the ﬂange.

2. Align the search light as shown in Figure 1.

Installation

Installation and Maintenance Instructions

Federal Signal www.fedsig.com

Figure 1 Search light mounted on ange

3. Push the search light down completely and turn clockwise

1/8 turn until the detent locks in place.

To remove the search light from the ﬂange:

1. Use a ﬂat-tipped screwdriver to push the detent while

turning the search light counterclockwise.

2. Pull up when the detent is free of the notch.

Wiring

NightSpire™Search Light

Federal Signal www.fedsig.com

If desired, permanently lock the ﬂange to the base using the

three #8 screws provided. See Figure 2.

Figure 2 Permanently locking the ange

Wiring

REVERSE POLARITY/MISWIRING: To avoid damage to the light,

ensure that the input voltage is the same as the voltage rating of

the light. Ensure that correct polarity is observed. Also ensure

that the unit is properly fused with a 5 A fuse.

Table 3 Wire Connections

Color Description Connection Point

Black Ground Battery Negative

Red Mode 1 Switched Positive 12 Vdc

To wire the search light:

1. Determine the required length of wires needed. The search

light is supplied with 6-Inch 20 AWG wires that can be

connected to longer wires if needed. For lengths up to 15

feet (5 m), use a minimum 18 AWG (1 mm) wire. For lengths

over 15 feet, use a minimum 16 AWG (1.5 mm) wire.

2. Install a 5 A fuse and fuse holder to the positive (+) terminal

at the voltage source. Connect one side of the power switch

to this fuse. Connect the light’s red wire to the switched

terminal of the switch.

Inhaltsverzeichnis

Sprachen:

Andere Federal Signal Corporation Beleuchtungsausrüstung Handbücher

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Valor VALR44 Handbuch

Federal Signal Corporation

Federal Signal Corporation Commander 371ST-250 Handbuch

Federal Signal Corporation

Federal Signal Corporation Reliant Handbuch

Federal Signal Corporation

Federal Signal Corporation CN SignalMaster Handbuch

Federal Signal Corporation

Federal Signal Corporation ELECTRARAY 225X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GH1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ELECTRARAY 225X Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation QuadraFlare QL64-TURN Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351012F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Viper S2 Light Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Signalmaster SMC14 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation STREAMLINE LP3E Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation FireRay Utility Light Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VIEWPOINT FVPK Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER SM518A Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CudaTriOptic 350205 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation QuadraFlare QL97HSCENE Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ILSFFVHL-CH08 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISTA 581016-OHP Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation XStream XSM Series Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Series Handbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung