Festo CPV Series Stücklistenhandbuch

Brief description

CPV valve

terminal with

direct connection

typeCPV...-DI02

PROFIBUS-DP

– English

8080225

2017-11a

[8080227]

Compact Performance

Festo CPV...-GE-DI02-8 2017-11a2

Translation of the original instructions

Documentation on the product

For all available product documentation

èwww.festo.com/pk

PROFIBUS®, PROFIBUS-DP® are registered trademarks of PROFIBUS

International (P.I.)

Festo SE & Co.

Ruiter Straße 82

73734 Esslingen

Germany

Internet: http://www.festo.com

E-Mail: service_international@festo.com

Reproduction, distribution or sale of this document or communication of

its contents to others without express authorization is prohibited.

a patent, utility model or design patent is registered.

English 3............................................

Festo CPV...-GE-DI02-8 2017-11a English 3

1 User instructionsEnglish

The CPV valve terminal with field bus direct connection

(CPV Direct) is intended exclusively for use as a slave on

the PROFIBUS-DP field bus (as per EN 50170) in industrial

applications.

The maximum values specified in the section “Technical

specifications” must be observed here. Detailed information

can be found in the Pneumatics manual P.BE-CPV-DI02-...

Warning

SSwitch off the power supply before connecting or

disconnecting plugs (otherwise this could lead to

functional damage).

SUse only power units which guarantee reliable

electrical isolation of the operating voltage as per

IEC/DIN EN60204-1. Observe also the general

requirements for PELV power circuits as per IEC/DIN

EN60204-1.

SConnect an earth conductor of sufficient diameter to

the connection marked with the earth symbol.

Festo CPV...-GE-DI02-8 2017-11a English4

2 Connection and display elements

1Field bus connection

2Connection for

voltage supply

3Bus status and

power LEDs

4LEDs for switching

status of the CP

valve coils

5DIL switches and

the SAVE button

6CPI extension

connection

7Switch cover

Pin assignment of power supply connection

M12 connection Pin no.

1. 24 V DC operating voltage for the electronics

and inputs *)

2. 24 V DC load voltage for valves

3. 0 V

4. Earth connection

*) On the CPI extension connection of connected modules

Festo CPV...-GE-DI02-8 2017-11a English 5

Example of connection with PELV power supply unit and

potential equalization

1PE

2Potential

equalization

3Load voltage can be

switched off

separately and

external fuses

4Earth connection

pin4 (max. 3 A)

MNS

3124

123 42

2 A

Pin assignment of the field bus connection (Sub-D-9 socket)

PROFIBUS-DP

Pin 3 (B) *) RxD/TxD-P

Pin 8 (A) *) RxD/TxD-N

*) In brackets: Connection on the Festo Sub-D plug type

FBS-SUB-9-GS-DP-B

Detailed information can be found in the manual

P.BE-CP-DI02-...

Festo CPV...-GE-DI02-8 2017-11a English6

3 Configuration

Caution

The CPV Direct contains electronically sensitive compo

nents. The CPV Direct will be damaged if you touch the

contact surfaces of the plug connectors or if you do not

observe the regulations for handling electrostatically

sensitive components.

Proceed with the configuration as follows:

1. Switch off the power supply.

2. Remove the switch cover.

3. Set the following with the DIL switch: the station

number, the device-related diagnosis for PROFIBUS-DP.

4. If modules or valve terminals are connected to the CPI

extension connection: Carry out automatic recognition

(see section 7).

5. Refit the switch cover.

6. If the CPI system is the first or last slave in a field bus

segment, the terminating resistor in the Festo Sub-D

plug must be activated.

Warning

SCheck the measures for putting the system into a

safe state in the event of an EMERGENCY STOP.

Further information: manual P.BE-CP-DI02-...

Festo CPV...-GE-DI02-8 2017-11a English 7

4 DIL switches

4.1 Set the station number

Set the station number for the PROFIBUS-DP with the

switch elements 1 … 7.

Permitted station numbers are: 1; …; 125

Coded entry Example: Station number: 38

20= 1

21= 2

22= 4

23= 8

24= 16

25= 32

26= 64

21+ 22+ 25=

2 + 4 + 32 =

4.2 Set device-related diagnosis

The device-related diagnosis can be activated/deactivated

with switch element 8 of the DIL switch.

Diagnosis ON Diagnosis OFF

Festo CPV...-GE-DI02-8 2017-11a English8

5 Addressing

The following applies in general for addressing the

CPVDirect:

1. A CPV valve terminal always occupies 16 output

addresses.

A CP valve location occupies two addresses:

– lower-value address = pilot solenoid 14

– higher-value address = pilot solenoid 12

2. CP valve terminals, electric input or output modules on

the CP extension string each occupy 8, 16, ... input or

output addresses depending on the design. Note the

relevant documentation for the module.

Detailed specifications and examples of addressing the

CPsystem can be found in the manual P.BE-CP-DI02-...

Festo CPV...-GE-DI02-8 2017-11a English 9

6 Diagnosis via LEDs

LED Operating status and fault display

(green)

Operating

voltage supply

(pin 1)

flashes: Undervoltage

off: Operating voltage not applied

(green)

Load voltage

supply (pin 2)

flashes fast: Undervoltage in valves of

CPVDirect

flashes slowly: Undervoltage in valves/

outputs in the CP string extension

off: Load voltage is not applied

BF Bus fault flashes fast: Non-permitted station number

set with DIL switch

flashes slowly: Field bus connection not OK

lights up: Hardware fault (servicing

required)

POther faults flashes fast: Configuration fault in CP string

flashes slowly: Module in the CP string has

diagnostic case

lights up: Module failure in the CP string

Festo CPV...-GE-DI02-8 2017-11a English10

7 CPI extension and SAVE button

7.1 Extension of the CPV Direct

You can connect CPI/CP modules and/or CP valve terminals

with and without extended functions to the CPI extension

connection.

The valve terminals CPV-DI02/CS02 are CPI masters.

Note the rules for the extension in section 8 “Technical

specifications” and in the manual P.BE-CPV-DI02-...

7.2 Saving the string assignment

Requirement: The modules in the CP string must be con

nected correctly, and the power supply must be switched

off.

1. Switch on the power supply for the CPV Direct and, if

applicable, for the CPI/CP modules/valve terminals.

With a new or modified string assignment the LED P

flashes.

2. Press the SAVE button for at least 1 s.

The LED goes out P.

3. Check the address assignments of your CPI system

before starting user programs.

Andere Handbücher für CPV Series

Inhaltsverzeichnis

Andere Festo Touch-Terminal Handbücher

Festo

Festo CPX-CM-HPP Bedienungsanleitung

Festo

Festo IFB-03 Series Bedienungsanleitung

Festo

Festo CPX-AB Series Bedienungsanleitung

Festo

Festo VTEM Bedienungsanleitung

Festo

Festo CPX-CMXX Stücklistenhandbuch

Festo

Festo CPV Series Bedienungsanleitung

Festo

Festo CPX Series Stücklistenhandbuch

Festo

Festo MPA-F Series Bedienungsanleitung

Festo

Festo VRUG-PT-L Bedienungsanleitung

Festo

Festo CPX-FB14 Bedienungsanleitung

Festo

Festo CPX Series Bedienungsanleitung

Festo

Festo MPA-C Series Bedienungsanleitung

Festo

Festo CDSA-D3-RV Bedienungsanleitung

Festo

Festo MPA-S Bedienungsanleitung

Festo

Festo CPV GEASI-4E4A Series Stücklistenhandbuch

Festo

Festo CPX-CEC Bedienungsanleitung

Festo

Festo CPV Series Stücklistenhandbuch

Festo

Festo VTEM Bedienungs- und Montageanleitung

Festo

Festo CPX-FB37 Bedienungsanleitung

Festo

Festo MPA-F Series Bedienungs- und Montageanleitung

Festo

Festo CPV10-GE-IBL-8 Bedienungsanleitung

Festo

Festo MPAC-VI Bedienungsanleitung

Festo

Festo CPX Series Bedienungsanleitung

Festo

Festo VIFB-21 Series Stücklistenhandbuch

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung