Franke 7612982104701 Bedienungsanleitung

ZMI_001_2000103385-HDTX538RS_#SALL_#AQU_#V3.fm / 07.12.20

Installation and operating instructions Montaż i instrukcja obsługi

EA-Nr.: 7612982104701

FAR-Best.-Nr.: 2000103385

HDTX538RS

Inhaltsverzeichnis11.fm

...................................................................................... 3

Please refer to the graphics in the German Installation and

Operating Instructions.

...................................................................................... 11

Prosimy przyjąć grafikę z niemieckiej instrukcji montażu i

obsługi.

- 3 -

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

0English

Urinal for wall mounting in car park WC with utility room A3000 open urinal

flush fitting 24 V DC.

Please refer to the graphics in the German Installation and Operating Instructions.

0Table of Contents

1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description of product

5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. ID settings (11200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

9. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Assembly, function and commissioning

10. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

11. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance

12. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

13. Replacing the filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

14. Replacing the ring sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

15. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

16. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

- 4 -

1. Abbreviations and units

2. Key

Warning!

Failure to observe can result in bodily injury or even death.

Caution!

Failure to observe can result in material damage.

☞Important!

Failure to observe can cause the product to malfunction.

☞Useful information for optimum handling of the product.

3. Warranty

Liability is accepted in accordance with the General Terms and Conditions of

Business and Supply.

Use only original spare parts!

4. Important notes

• Installation, commissioning and maintenance must be performed only by a

qualified expert in accordance with the instructions provided, legal requirements

and recognised engineering standards.

• All technical connection regulations specified by the local water and electricity

supply companies must be observed.

DN Nominal diameter in mm

RCD Residual current protective device,

Earth leakage circuit breaker

SELV Safety extra low voltage

WS Wrench size

EA-Nr. European article number

FAR-Best.-Nr. Franke Aquarotter order number

Conversion 1 mm = 0.03937 inches

1 inch = 25.4 mm

All length specifications in the graphics are in mm.

- 5 -

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

• The power supply should be switched off before any work is carried out.

• We reserve the right to make changes.

5. Application

A3000 open, non-contact, electronically controlled urinal flush valve, with concealed

triggering via heat ring sensor, in combination design for rear wall installation,

with possibility of external control, such as tap settings and communication via ECC

function controller. The flow time can be set in one-second steps.

6. Technical specifications

7. ID settings (11200)

Urinal / ring sensor / RPE-MV

FUNCTION:

Flush approx. 25 s after start of use. Post flushing 1 sec. after approx. 36 s (to fill the

siphon).

SENSORS:

S2: Channel 1 / ring sensor

ACTUATORS:

A1: Channel 1 / solenoid valve / RPE

Minimum flow pressure: 1.0 bar

Recommended flow pressure: 1-5 bar

Maximum operating pressure: 10 bar

Calculated flow rate: 0.3 l/s

Flushing flow: 0.3-0.7 l/s

Flush water volumes 2–4 l adjustable

Operating voltage: 24 VDC

Power consumption: 7 W

Protection class: Electronics IP 68, solenoid valve IP 40

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

- 6 -

SETTINGS:

8. Dimensions

9. Installation example

A: Front view

B: Front view wall recess

C: Side view

D: View of utility room

10. Assembly

Warning!

• Operate the product only with safety extra low voltage (SELV). The components

must not be earthed.

• Place the power supply (not part of the delivery scope, see accessories,

Chapter 14) outside the wet area in a separate room.

• Protect the electrical connection with a residual current circuit breaker (RCD).

Failure to observe this instruction can result in death or material damage due to

electric shock or fire, for example.

Range - / - / -

TempSensor 1 action -

TempSensor 2 action -

AquaPay -

Flow Time 8 sec. / - / -

Overrun time - / - / -

Safety shutdown after -

Reflection alarm after -

Concurrence suppression -

Flow time reduction -

Cleaning deactivation 1 min.

Hygiene flush (dynamic) Interval: 24 h/flow time: 10 sec.

Hygiene flush (fixed) Interval: 0 h/flow time: 10 sec.

Power-on flush Delay: 0 sec / flow time: 5 sec.

TD Application Time -

TD water saving function -

TD cooling -

- 7 -

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

☞Lay the system line (not included in delivery, see Chapter 16.) in the empty pipe

(to be provided by the customer) from the power supply to the fittings and loop

through.

☞Important!

Prior to the assembly process, flush the pipework in accordance with DIN 1988.

Warning!

Only operate taps with the designated filter.

Failure to observe this instruction can result in damage to the tap.

☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.

☞Depending on the composition of the wall, special wall plugs may have to be used

(to be provided by the customer).

a: Sensor

Installing the electrical T-distributor

☞Important!

The components of the electrical T-distributor may only be installed after the power

has been switched off.

☞For system cable recommendations, see Chapter 12., Accessories.

When using cables other than the system cable, pay attention to the different colour

code. The outer diameter must not exceed 7.5 mm.

10.1

Remove the sheathing (a) of the system cable (approx. 40 mm).

10.2

Push the cap nut (c) onto the system cable (b) up to the limit stop.

☞The various wire guides are marked with numbers 1 to 4.

A: Union nut

B: FAR-Best.-Nr. 2000104272

FAR-Best.-Nr. 2000104274

FAR-Best.-Nr. 2000100801

FAR-Best.-Nr. 2000100852

10.3

Engage the wires (d) on the wire guides (e) according to their colours.

10.4

Cut off the projecting wire ends flush, i.e. without protrusions.

10.5

Push the union nut (c) onto the electrical T-distributor (f) and tighten it to the required

torque (1.2 Nm).

1 brown red

2white white

3 blue blue

4 black black

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

- 8 -

Caution!

Note the polarity.

The same wire colour must be in the same wire guide for both union nuts.

☞When tightening the union nut, the electrical contact and tension relief are created

automatically.

Special seals act as protection from dust and water.

10.6

Connect the cables between the electronics module, solenoid valve cartridge,

and sensor.

A: Solenoid valve cartridge

B: Actuator 2 (optional)

C:0-10 V analogue output

D:Cold water temperature sensor (optional)

E: Hot-water temperature sensor (optional)

F: Sensor connection 2/3(optional)

G: Sensor

H:Electrical T-distributor system cable (power)

K: Electronic module

10.7

Use a hexagonal wrench to close the water volume regulator.

h: closed

i: open

10.8

Unscrew the locking screw (k) on the water volume regulator.

10.9

Insert the filter (l).

☞Important!

Note the installation position of the filter.

10.10

Open the water quantity regulator.

11. Function

☞The temperature of the liquid placed in the urinal must be higher than the ambient

temperature.

11.1

Use the urinal.

• After approx. 25 seconds, the urinal is flushed for 8 seconds.

• After another second, the urinal is flushed again for 0.5 seconds. This ensures

that the odour seal is filled.

☞An automatic flushing function after 24 hours of non-use has been factory-set.

11.2

You can set the flow time and automatic flush using the system software.

- 9 -

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

12. Maintenance and care

The tap must be checked and maintained at regular intervals in accordance with the

water quality and the local conditions and rules and regulations applicable at the site

(DIN EN 806-5).

Maintain the following components:

• Filter (see Chapter 16.)

Use suitable cleaning agents which do not attack the tap in a proper manner and

rinse with water after use. High-pressure cleaners must not be used for cleaning.

13. Replacing the filter

Water volume regulator filter

13.1

Unscrew the locking screws (a) on the water volume regulators.

13.2

Replace the filters (b).

☞Important!

Note the installation position of the filters.

13.3

Reassemble in reverse order.

14. Replacing the ring sensor

14.1

Use a hexagonal wrench to close the water volume regulator.

14.2

Disconnect the electronics module from the system cable.

14.3

Disassemble the drain pipe (a).

14.4

Disassemble the drain valve (b) and the ring sensor (c).

☞Before reassembly, apply thermal paste (to be provided by customer) to the ring

sensor evenly. Avoid air transitions around the entire perimeter.

14.5

Reassemble in reverse order.

ZMI_001_2000103385-HDTX538RS_#SEN_#AQU_#V3.fm

- 10 -

15. Troubleshooting

If you cannot rectify a fault or if it is not in the list, please contact our customer

service department!

16. Spare parts

Fault Cause Remedy

Water does not flow – Water volume regulator closed ➯Open it

– Power supply interrupted ➯Restore it

– Water supply interrupted ➯Restore it

– Electronics module faulty ➯Replace it

– Solenoid valve faulty ➯Replace it

Water flows

continuously

– Dirty solenoid valve ➯Clean it

– Solenoid valve faulty ➯Replace it

Water volume too low – Supply pressure too low ➯Check it

– Dirty filter ➯Clean it

– Water volume regulator not fully

open

➯Open it

Accessories Order No.

ECC2 function controller (60 W)

with Ethernet connection . . . . . . . 2000108123

Power pack (12 W) . . . . . . . . . . . . . . 2000100375

Power pack (60 W) . . . . . . . . . . . . . . 2030027537

System cable for continuous

use in water,

Halogen-free 100 m . . . . . . . . . . . 2000104272

Halogen-free 25 m . . . . . . . . . . . . 2000104274

System cable,

Not halogen-free 100 m . . . . . . . . 2000100801

Not halogen-free 25 m . . . . . . . . . 2000100852

Description Order No.

1 Electronics module M1. . . . . . . . . . . . 2030051833

2 24 V DC solenoid valve . . . . . . . . . . . 2000104454

3 Filter (packaging unit 10x) . . . . . . . . . 2000104749

4 Ring sensor . . . . . . . . . . . . . . . . . . . . 2000109506

Mounting kit consisting of:

Filter

O-ring

Seals. . . . . . . . . . . . . . . . . . . . . . . 2000104872

Inhaltsverzeichnis

Sprachen:

Andere Franke Sanitärprodukte Handbücher

Franke

Franke AQRE432 Bedienungsanleitung

Franke

Franke F5SM1007 Bedienungsanleitung

Franke

Franke ORBIT Handbuch

Franke

Franke AHWSS1720WIS-00 Bedienungsanleitung

Franke

Franke F5LM1015 Bedienungsanleitung

Franke

Franke CMPX551GE Bedienungsanleitung

Franke

Franke F4 F4LT1002 Bedienungsanleitung

Franke

Franke F5 Series Bedienungsanleitung

Franke

Franke SIRIUS BS302 Bedienungsanleitung

Franke

Franke SIRIUS WB440COP Bedienungsanleitung

Franke

Franke ACXX2008 2030051217 Bedienungsanleitung

Franke

Franke XINH203 Bedienungsanleitung

Franke

Franke EXOS616EX Bedienungsanleitung

Franke

Franke HDTX0013 Bedienungsanleitung

Franke

Franke F3SM2004 Bedienungsanleitung

Franke

Franke AQCT0073 Bedienungsanleitung

Franke

Franke DFD901 Bedienungsanleitung

Franke

Franke FRESNO FSG 111 Bedienungsanleitung

Franke

Franke F5ST2011 Bedienungsanleitung

Franke

Franke XINX617 Bedienungsanleitung

Franke

Franke F3 ASSV1005 Bedienungsanleitung

Franke

Franke CMPX532WF Bedienungsanleitung

Franke

Franke ACXT2001 Bedienungsanleitung

Franke

Franke AQUAJET-SLIMLINE AQUA750 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema