Front Runner KSTF003T Bedienungsanleitung
KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
KSTF001
ENG
1
TOYOTA 4runner (2010 -CURRENT)
SLIMSPORT ROOF RACK KIT
Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting system specific to your vehicle
2. A Front Runner Rack Tray or Load bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
READ ME FIRST
START HERE!
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
2
13mm
10mm
Sealant Marker
Insulation
Tape
FIGURE 1.1
IN THE BOX
1 2 X Foot Rail Front LH / RH
2 2 X Foot Rail Rear LH / RH
3 2 X Stiffener Plate 01
4 2 X Stiffener Plate 02
5 2 X Stiffener Plate 03
6 2 X Splice Plate
7 11 X Slimsport Slat
8 44 X M6 x 25 Thread Forming Screw
9 20 X M6 x 16 Flange Button Head
10 20 X M6 Nyloc Nut
11 22 X M6 Nut Cap
12 8 X 10mm Plastic Spacer
13 8 X M8 x 19 x 12 Flat Washer
14 8 X M8 Spring Washer
15 2 X M6 x 12 x 1 Flat Washer
IN THE BOX
16 2 X M6 Spring Washer
17 2 X M6 x 30 Hex Bolt
18 8 X M8 x 60 Hex Bolt
19 3 X Jack Nut Long
20 1 X Jack Nut Tool
21 2 X M6 x 30 Button Head
22 8 X M8 Nut Cap
Anti Seize / Oil
1GET ORGANIZED
TOOLS NEEDED
Torx
T30
Cordless
Driver
CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
5mm
12mm
8
22
17
14
15
19
11
3
10
20
21
13
14
18
22
12
4
6
11
10
1
2
5
7
9
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
KSTF001_REV_A04
ASSEMBLY
2
2.1
2.2
Secure the Splice Plates (Item 6) to the Foot
Rails (Items 1 & 2) as shown using M6 x 16
Flange Button Head Bolts and M6 Nyloc Nuts
(Items 9 & 10).
Secure the Stiffener Plates (Items 3, 4, & 5)
to the Foot Rails (Items 1 & 2) using M6 x 16
Flange Button Head Bolts and M6 Nyloc Nuts
(Items 9 & 10)
Do this to both LH & RH Foot Rails.
Place M6 Nut Caps (Item 11) over all Nyloc
Nuts.
Fit 10 Slimsport Slats (Item 7) to assembly
2.1 using M6 x 25 Thread Forming Screws
(Item 8).
Note do not fit front slat.
Apply a little Anti Seize / oil on screw
threads before inserting. Note these are
thread forming screws.
3
10
11
4
10
11
1
2
9
6
10
11
10
11
5
7
8
Torx
T30
10mm
Torx
T30
Cordless
Driver
Tightening Torque 8-10Nm /
5.9 ft lb - 7.38 ft lb. Take care when
using a cordless driver.
Remove
Remove
370mm
445mm
With the factory rails removed and starting at
the front edge of the molding, measure and
mark the dimensions as shown onto both the
LH & RH ditch moldings.
3.1
PREPERATION
3
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
KSTF001_REV_A04
PREPERATION
3
3.2
3.3
3.4
Place the assembled Rack on the vehicle,
lining up the holes in the foot rail with the
factory holes in the roof. Mark the hole
centres where the ditch moldings were cut
out.
Remove the Rack.
Before drilling the holes in the roof, take both
the 5mm & 12mm drill bits and wrap a band
of insulation tape around each bit to act as a
stopper to prevent you from drilling to deep
as there are airbags located below where you
will be drilling.
Drill a 5mm pilot hole on both markings.
Open holes to 12mm.
Insert the M6 Button Head Bolt (Item 21) into
the one side of the Installer Wrench (Item 20),
loosly fit a Jack Nut (Item 19) to the Button
Head Bolt as shown.
Using the Installer Wrench and a M6 x 30
Button Head Bolt, insert the M6 Jack Nuts
into the holes drilled.
Place the Assembly into the holes drilled in
3.3. Using a battery powered screw driver
and a 4mm Allen Key Bit, set the Jack Nut
into the hole while holding onto the handle
of the Installer Wrench.
10mm From the tip of the drill to start of tape
10mm
Make sure that the Jack Nut has pulled
up all the wat to the inside skin of the
roof panel.
Cordless
Driver
PERMANENT FITMENT (RECOMMENDED
Insulation
Tape
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
5
KSTF001_REV_A04
FIT AND SECURE
4
4.1
4.2
Place silicone into and around each of the
fixing points.
Place Spacers (Item 12) over the mounting
holes.
Remove the backing from the double sided
tape (4.2a) on the bottom of the Support Plate
01 (Item 3) and push the plate firmly down
onto the body of the vehicle.
Secure Rack assembly 2.2 using M6 x
12 x 1 Flat Washers, M6 Spring Washers
and M6 x 30 Hex Bolts for front foot
(Items 14, 15 & 17).
Place a bead of silicone down the length of
each M6x20 bolt before inserting.
Secure the middle and back feet using M8 x
19 x 2 Flat Washers, M8 Spring Washers and
M8 x 60 Hex Bolts (Item 18, 13 & 14).
Fasten the front foot by inserting the fastener
(item 17) through the double sided tape and
securing into the Jack Nut fitted earlier.
Fully tighten all fasteners.
Place M6 and M8 Nut Caps over all hex Bolts.
15
3
14
17
a
22
22
18
13
14
12
12
10mm
13mm
Remove
Remove
370mm
445mm
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
6
KSTF001_REV_A04
PREPERATION
5
5.1
5.2
With the factory rails removed and starting at
the front edge of the molding, measure and
mark the dimensions as shown onto both the
LH & RH ditch moldings.
Use denatured alchohol and ensure the ditch
is clean from any residue where the Support
Plate 01 (Item 3) will be resting on the ditch.
TEMPORARY FITMENT
a
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
7
KSTF001_REV_A04
FIT AND SECURE
6
6.1
6.2
Place silicone into and around each of the
fixing points.
Place Spacers (Item 12) over the mounting
holes.
Remove the backing from the double sided
tape (4.2a) on the bottom of the Support Plate
01 (Item 3) and push the plate firmly down
onto the body of the vehicle.
Secure Rack assembly 2.2 using M6 x
12 x 1 Flat Washers, M6 Spring Washers
and M6 x 30 Hex Bolts for front foot
(Items 14, 15 & 17).
Place a bead of silicone down the length of
each M6x20 bolt before inserting.
Secure the middle and back feet using M8 x
19 x 2 Flat Washers, M8 Spring Washers and
M8 x 60 Hex Bolts (Item 18, 13 & 14).
Fully tighten all fasteners.
Place M6 and M8 Nut Caps over all hex Bolts.
22
18
13
14
12
12
10mm
13mm
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
8
KSTF001_REV_A04
FIT AND SECURE
7
7.1
7.2
Refer to fitment guide RRAC234
Refer to fitment guide RRAC195
10mm
STANDARD WIND FAIRING ASSEMBLY
LIGHT BAR WIND FAIRING ASSEMBLY
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
9
KSTF001_REV_A04
4
COMPLETION
8
8.1
Congratulations! You did it. Take a step back and admire your work!
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
9
Now's the time to visit your favorite Front Runner dealer in person or online.
IMPORTANT!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER
FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
Dieses Handbuch passt für folgende Modelle
1
Andere Front Runner Autozubehör Handbücher
Front Runner
Front Runner LAMS004 Bedienungsanleitung
Front Runner
Front Runner SLIMPRO KVXS006 Handbuch
Front Runner
Front Runner SSDS115 Bedienungsanleitung
Front Runner
Front Runner SSDS110 Bedienungsanleitung
Front Runner
Front Runner TRAC003 Bedienungsanleitung
Front Runner
Front Runner BPTH007 Bedienungsanleitung
Front Runner
Front Runner FSLI023 Bedienungsanleitung
Front Runner
Front Runner SSDR012 Bedienungsanleitung
Front Runner
Front Runner BRONCO TBRA040 Bedienungsanleitung
Front Runner
Front Runner KSVT001 Bedienungsanleitung
Front Runner
Front Runner SlimSport KSFR002 Bedienungsanleitung
Front Runner
Front Runner TRCA010 Bedienungsanleitung
Front Runner
Front Runner Easy-Out Bedienungsanleitung
Front Runner
Front Runner RRAC269 Bedienungsanleitung
Front Runner
Front Runner RRAC242 Bedienungsanleitung
Front Runner
Front Runner FAJK003 Bedienungsanleitung
Front Runner
Front Runner RRAC105 Bedienungsanleitung
Front Runner
Front Runner SSDR005 Bedienungsanleitung
Front Runner
Front Runner LAMS001 Bedienungsanleitung
Front Runner
Front Runner LATF002 Bedienungsanleitung
