Front Runner SSBS008 Bedienungsanleitung

Load Bed Cargo Slide

MKIII -Medium

SSBS008

ENG

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.

IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH.

YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.

THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE.

IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES,

YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

READ ME !

Thank you for purchasing a Front Runner Load Bed Cargo Slide.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

TOOLS NEEDED

17MM

10MM 10MM

17MM

FIGURE 1.1

4mm

9.5mm

1 1 X Load Bed Cargo Slide MKIII - Medium

2 1 X M6x25 Countersink Bolt

3 1 X M10 Flat Washer

4 9 X M6x40 Hex Bolt

5 2 X M8 Nyloc Nut

6 5 X M6x25 Hex Bolt

7 10 X M6 Rivnut

8 9 X M6 Spring Washer

9 6 X 19x12.58x12 Aluminium Spacer

10 9 X M6x30x1 Flat Washer

GET ORGANIZED

IN THE BOX

Here is what you are looking at for SSBS008

4mm

2 3

4 5

6 7

8 9

FIT AND SECURE

2.1

2.2

2.3

Before ﬁtting the Cargo Slide in the vehicle,

remove the wood base by loosening the

four M6 Button Head Bolts.

To loosen the two rear bolts, open the Cargo

Slide.

10MM

The front mounting brackets may be

relocated backwards should it be required

to obtain a more suitable mounting position

as shown in diagram 2.3.

Looking at both the left and right rear

corners of the Cargo Slide (Item 1), loosen

and remove the rubber stopper. This is done

by gripping the stopper to prevent it from t

urning and removing the M6 button head

bolt as shown. Once removed keep in a safe

place as you will need to replace them at a

later stage.

Place the Cargo Slide into the vehicles load

bed. Carefully pull the "tray" free from the

frame and store in a safe place until later.

Position the frame, front to back and left to

right. Load beds vary with each

manufacturer, so the exact positioning of

the frame will vary from vehicle to vehicle. I

t is advisable to get all mounting points in

the center of the raised sections that run

the length of the load bed, however in the

event of mounting points not lining up with

raised sections,spacers have been

provided.

Stopper

4MM

17MM

FIT AND SECURE

2.4

2.5

2.6

Place the frame back onto the load bed and

secure using the fasteners and spacers

supplied. The spacers (Item 5) are to be

used when the mounting points are in a

"dip" and not on a raised section by

placing it over the rivnut so that the frame

rests on the spacer.

When securing the front of the frame use

the M6x25 countersunk screw, M10 ﬂat

washer and a spacer

Refer to Step 2.2, reﬁt the tray and

stoppers. Once reﬁtted check that the push

to close latch engages fully and that the

slide is secure.

4MM

9MM

Make sure you have closed the load bed tail

gate to ensure that it does not make

contact with the frame. Once you are

satisﬁed with the positioning of the frame,

mark the position of all the mounting points

as indicated by the arrows onto the load

body.

Remove the frame and drill a 4mm pilot

hole on each of your markings. Check the

underside of the load bed before drilling to

make sure that there is no piping or wiring

in the way. Re-drill all of the pilot holes to

9mm.

Insert and crimp a M6 rivnut (Item 6) into

each of the holes you have drilled.

4MM

10MM

Congratulations! You did it. Take a step back and admire your work!

COMPLETION

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner Dealer in person or online.

3.1

Inhaltsverzeichnis

Andere Front Runner Autozubehör Handbücher

Front Runner

Front Runner LAMG002 Bedienungsanleitung

Front Runner

Front Runner SSDR011 Bedienungsanleitung

Front Runner

Front Runner SHOW013 Bedienungsanleitung

Front Runner

Front Runner SAFE010 Bedienungsanleitung

Front Runner

Front Runner Drawer 6 Box Large MKII SSWO008 Bedienungsanleitung

Front Runner

Front Runner LALD006 Bedienungsanleitung

Front Runner

Front Runner Toyota LAND Cruiser 100 SLIMLINE II Bedienungsanleitung

Front Runner

Front Runner SLIMLINE II KRSO004T Handbuch

Front Runner

Front Runner LADD007 Bedienungsanleitung

Front Runner

Front Runner SSDS115 Bedienungsanleitung

Front Runner

Front Runner SSAM008 Bedienungsanleitung

Front Runner

Front Runner SSDS102 Bedienungsanleitung

Front Runner

Front Runner Slimline II KRKS007T Bedienungsanleitung

Front Runner

Front Runner LALD004 Bedienungsanleitung

Front Runner

Front Runner QE Series Bedienungsanleitung

Front Runner

Front Runner JADA010 Bedienungsanleitung

Front Runner

Front Runner TBRA039 Bedienungsanleitung

Front Runner

Front Runner SSDR012 Bedienungsanleitung

Front Runner

Front Runner Slimline II FATF005 Bedienungsanleitung

Front Runner

Front Runner BPTH007 Bedienungsanleitung

Front Runner

Front Runner TBRA034 Bedienungsanleitung

Front Runner

Front Runner RRAC901 Bedienungsanleitung

Front Runner

Front Runner SSDS802 Bedienungsanleitung

Front Runner

Front Runner RRAC189 Kurzanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung