FuzzDog Pussy King Bedienungsanleitung

Pussy King

Glorious mash-up of a

ToneBender kII and a Rat

No reproduction permitted without the express written

Schematic + BO

R1 1

R2 100K

R3 1K

R4 470K

R5 1K

R6 1K

R7 3K9

R8 10K

R9 22K

R10 3K9

R11 2K2

R12 1K

R13 1

R14 1

R15 3K3

R16 150R

R17 2K2 (CLR)

C1 68n

C2 1n

C3 22u elec

C4 150n

C5 10u elec

C6 22u elec

C7 4u7 elec

C8 3n3

C9 220n

C10 1u elec

C11 10n

C12 47u elec

C13 47p

D1-2 1N4148

D3 1N4001

D4-5* Your choice

Q1-4** 2N3904

GAIN 50KA

VOL 100KA

FILT 100KA

INP 250KB

SW1‡SPDT ON-ON

*Optional extra clipping in conjunction with SW1.

Experiment with different diodes here.

At FuzzDog HQ we liked blue LEDs.

**Original reportedly uses BC550B, but most NPN

BJTs with an hFE around 350-400 will work ok.

‡Only required if you’re going for the extra clipping.

If not you need a jumper wire. See next page.

The power and signal pads on

the PCB conform to the

FuzzDog Direct Connection

format, so can be paired with

the appropriate daughterboard

for quick and easy offboard

wiring. Check the separate

daughterboard document for

details.

Be very careful when soldering

the transistors and diodes.

They’re very sensitive to heat.

You should use some kind of

heat sink (crocodile clip or

reverse action tweezers) on

each leg as you solder them.

Keep exposure to heat to a minimum (under 2 seconds).

Snap the small metal tag off the pots so they can be mounted flush in the box.

Positive (anode) legs of the electrolytic caps go to the square pads. C12 can be laid flat as

shown in the cover image to give you extra clearance in the enclosure.

Negative (cathode) legs of the diodes go to the square pads.

You should solder all other board-mounted components before you solder the pots. Once

they’re in place you’ll have no access to much of the board. ake sure your pots all line up

nicely. The best way to do that is to solder a single pin of each pot in place then melt and

adjust if necessary before soldering in the other two pins. If your pots don’t have protective

plastic jackets ensure you leave a decent

gap between the pot body and the PCB

otherwise you risk shorting out the circuit.

If you aren’t going for the optional extra

clipping diodes and switch, place a jumper

wire as shown in red above. This will keep

D1-2 in the circuit all the time.

INPUT and GAIN both effect the gain level in

different ways. It’s well worth spending

some time experimenting with different

settings.

The FILTER control works the opposite way

to what you might expect. Deal with it.

Test the board!

U DER O CIRCUMSTA CES will troubleshooting help be

offered if you have skipped this stage. o exceptions.

Once you’ve finished the circuit it makes sense to test is before starting on

the switch and LED wiring. It’ll cut down troubleshooting time in the long

run. If the circuit works at this stage, but it doesn’t once you wire up the

switch - guess what? You’ve probably made a mistake with the switch.

Solder some nice, long lengths of wire to the board connections for 9V, G D,

I and OUT. Connect I and OUT to the jacks as shown. Connect all the

G Ds together (twist them up and add a small amount of solder to tack it).

Connect the battery + lead to the 9V wire, same method. Plug in. Go!

If it works, crack on and do your switch wiring. If not... aw man. At least you

know the problem is with the circuit. Find out why, get it working, THE

worry about the switch etc.

BATTERY

IN OUT

Your nice, new circuit board

INCLUDING WIRED POTS!!!!

IN 9V GND OUT

Wire it up (if using a daughterboard please refer to the relevant document)

Wiring shown above will disconnect the battery when you remove the jack

plug from the input, and also when a DC plug is inserted.

The Board G D connections don’t all have to directly attach to the board. You

can run a couple of wires from the DC connector, one to the board, another to

the I jack, then daisy chain that over to the OUT jack.

It doesn’t matter how they all connect, as long as they do.

This circuit is standard, egative G D. Your power supply should be Tip

egative / Sleeve Positive. That’s the same as your standard pedals (Boss etc),

and you can safely daisy-chain your supply to this pedal.

PedalParts.co.uk

BOARD

OUT

BOARD

GND

BOARD

GND

BOARD

GND

BOARD

INPUT

BATTERY

OUT

BOARD

GND

BOARD

LED+

This template is a rough guide only. You should ensure correct marking of your

enclosure before drilling. You use this template at your own risk.

Pedal Parts Ltd can accept no responsibility for incorrect drilling of enclosures.

PedalParts.co.uk

Drilling template

Hammond 1590B

60 x 111 x 31mm

Recommended drill sizes:

Pots 7mm

Jacks 10mm

Footswitch 12mm

DC Socket 12mm

32mm

27mm

It’s a good idea to drill

the holes for the pots

1mm bigger to give

yourself some wiggle

room, unless you’re a

drill ninja.

Inhaltsverzeichnis

Andere FuzzDog Musikpedal Handbücher

FuzzDog

FuzzDog PHASE 90 Bedienungsanleitung

FuzzDog

FuzzDog JenFuzz Bedienungsanleitung

FuzzDog

FuzzDog FY2 Bedienungsanleitung

FuzzDog

FuzzDog The Wobbler Bedienungsanleitung

FuzzDog

FuzzDog Super Fuzz Bedienungsanleitung

FuzzDog

FuzzDog BrassBlender Bedienungsanleitung

FuzzDog

FuzzDog Clay Jones OD V2 Bedienungsanleitung

FuzzDog

FuzzDog Ultimatum Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Repeater V4 Bedienungsanleitung

FuzzDog

FuzzDog BSIAB2 Bedienungsanleitung

FuzzDog

FuzzDog Ruby/NoisyCricket Bedienungsanleitung

FuzzDog

FuzzDog DeathDrive Bedienungsanleitung

FuzzDog

FuzzDog The Gimp Bedienungsanleitung

FuzzDog

FuzzDog Bionic GuzzFun Bedienungsanleitung

FuzzDog

FuzzDog AB/Y Bedienungsanleitung

FuzzDog

FuzzDog Peachy Fuzz Bedienungsanleitung

FuzzDog

FuzzDog GimpFX Ultr-Fk Bedienungsanleitung

FuzzDog

FuzzDog Animatron Bedienungsanleitung

FuzzDog

FuzzDog Mutant Fuzz Bedienungsanleitung

FuzzDog

FuzzDog 7 of Dwarves Auto Wah Bedienungsanleitung

FuzzDog

FuzzDog MicrAmp Bedienungsanleitung

FuzzDog

FuzzDog Rodent Bedienungsanleitung

FuzzDog

FuzzDog Gristleiser Bedienungsanleitung

FuzzDog

FuzzDog KlonBuffer V3 Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung

TREX

TREX ToneBug Totenschläger Bedienungsanleitung

BBE

BBE ORANGE SQUASH Bedienungsanleitung