FuzzDog Super Fuzz Bedienungsanleitung

Super Fuzz

Shin-Ei’s utterly

uncompromising monster

No reproduction permitted without the express written

Important notes

If you’re usin any of our footswitch dau hterboards,

DOWNLOAD THE DAUGHTERBOARD DOCUMENT

•Download and read the appropriate build document for the daughterboard

as well as this one BEFORE you start.

•DONOT solder the supplied Current Limiting Resistor (CLR) to the main

circuit board even if there is a place for it. This should be soldered to the

footswitch daughterboard.

POWER SUPPLY

Unless otherwise stated in this document this circuit is designed to be

powered with 9V DC.

COMPONENT SPECS

Unless otherwise stated in this document:

•Resistors should be 0.25W. You can use those with higher ratings but

check the physical size of them.

•Electrolytics caps should be at least 25V for 9V circuits, 35V for 18V

circuits. Again, check physical size if using higher ratings.

LAYOUT CONVENTIONS

Unless otherwise stated in this document, the following are used:

•Electrolytic capacitors:

Long leg (anode) to square pad.

•Diodes:

Striped leg (cathode) to square pad.

•ICs:

Square pad indicates pin 1.

Schematic + BOM

R1 22

R2 100

R3 100

R4 1 8

R5 47

R6 470

R7 10

R8 47

R9 3 3

R10 150

R11 10

R12 220

R13 10

R14 100

R15 10

R16 100

R17 470R

R18 22

R19 1 8

R20 22

R21 47

R22 470R

R23 10

R24 22

R25 10

R26 100 (750 )

R27 15 (75 )

R28 10 (24 )

R29 1 (1 2)

R30 100

C1 10u

C2 10u

C3 10u

C4 10u

C5 10u

C6 10u

C7 10u

C8 100n

C9 10u

C10 10u

C11 1n

C12 100n

C13 10u

C14 10u

C15 2n2*

C16 100u

Q1-6 2N5088**

D1,2 1N34A

D3 1N4001

D4,5 1N4148***

OCT 10 TRIM

EXP 50 B

VOL 50 B

TONE SPDT ONON

DIODE SPDT ONON

Alternative values shown in blue are from the Wattson EFY-6 version of the Superfuzz, giving higher output.

*sometimes shown as 1n

**any low-ish gain NPN silicon transistors can be experimented with, i.e. 2N222A, 2N3904, BC107

***optional. Don’t bother putting them in if you’re not using the diode selection switch. Other diodes can be

experimented with.

The power and signal pads on the PCB conform

to the FuzzDog Direct Connection format, so can

be paired with the appropriate daughterboard for

quick and easy offboard wiring. Check the

separate daughterboard document for details.

Be very careful when soldering the LEDs, diodes

and transistors. They’re very sensitive to heat.

You should use some kind of heat sink (crocodile

clip or reverse action tweezers) on each leg as

you solder them. eep exposure to heat to a

minimum (under 2 seconds).

Snap the small metal tag off the pots so they can

be mounted flush in the box.

You should solder all other board-mounted

components before you solder the pots. Once

they’re in place you’ll have no access to much of

the board. Make sure your pots all line up nicely.

The best way to do that is to solder a single pin

of each pot in place then melt and adjust if

necessary before soldering in the other two pins.

If your pots don’t have protective plastic jackets

ensure you leave a decent gap between the pot

body and the PCB otherwise you risk shorting

out the circuit.

If you aren’t adding the diode selection switch

you’ll have to jumper the correct pads as shown

above depending on whether you’re using D1-2

(blue) or D4-5 (red).

Be VERY careful when bending the legs of the

1N34A. The glass case is very fragile and likely

to break. Best to hold the leg with some needle-

nosed pliers against the case, and bend the leg

with your finger so the pliers are taking any

strain away from the diode.

Test the board!

Check the relevant dau hterboard document for more

info before you undertake this sta e.

UNDER NO CIRCUMSTANCES will troubleshootin help

be offered if you have skipped this sta e. No exceptions.

Once you’ve finished the circuit it makes sense to test is before starting on the switch and LED

wiring. It’ll cut down troubleshooting time in the long run. If the circuit works at this stage, but it

doesn’t once you wire up the switch - guess what? You’ve probably made a mistake with the switch.

Solder some nice, long lengths of wire to the board connections for 9V, GND, IN and OUT. Connect

IN and OUT to the jacks as shown. Connect all the GNDs together (twist them up and add a small

amount of solder to tack it). Connect the battery + lead to the 9V wire, same method. Plug in. Go!

If you’re using a ribbon cable you can tack the wires to the ends of that. It’s a lot easier to take them

off there than it is do desolder wires from the PCB pads.

If it works, carry on and do your switch wiring. If not... aw man. At least you know the problem is

with the circuit. Find out why, get it working, THEN worry about the switch etc.

Your completed circuit board

includin pots

Wiring shown above will disconnect the battery when you remove the jack plug

from the input, and also when a DC plug is inserted.

The Board GND connections don’t all have to directly attach to the board. You

can run a couple of wires from the DC connector, one to the board, another to

the IN jack, then daisy chain that over to the OUT jack.

It doesn’t matter how they all connect, as long as they do.

This circuit is standard, Negative GND. Your power supply should be Tip

Negative / Sleeve Positive. That’s the same as your standard pedals (Boss etc),

and you can safely daisy-chain your supply to this pedal.

BOARD

OUT

BOARD

GND

BOARD

GND

BOARD

GND

BOARD

INPUT

BATTERY

OUT

BOARD

GND

BOARD

Wire it up (if using a daughterboard please refer to the relevant document)

This template is a rough guide only. You should ensure correct marking of your

enclosure before drilling. You use this template at your own risk.

Pedal Parts Ltd can accept no responsibility for incorrect drilling of enclosures.

FuzzDog.co.uk

Drilling template

Hammond 1590B

60 x 111 x 31mm

It’s a good idea to drill the pot and

toggle switch holes 1mm bigger i

you’re board-mounting them.

Wiggle room = good!

Recommended drill sizes:

Pots 7mm

Jacks 10mm

Footswitch 12mm

DC Socket 12mm

Toggle Switches 6mm

21mm

23mm

32mm

Inhaltsverzeichnis

Andere FuzzDog Musikpedal Handbücher

FuzzDog

FuzzDog The Gimp Bedienungsanleitung

FuzzDog

FuzzDog Gristleiser Bedienungsanleitung

FuzzDog

FuzzDog JenFuzz Bedienungsanleitung

FuzzDog

FuzzDog Wrecktifier Bedienungsanleitung

FuzzDog

FuzzDog Peachy Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Repeater V4 Bedienungsanleitung

FuzzDog

FuzzDog Tone Bender Mk II Bedienungsanleitung

FuzzDog

FuzzDog RockBox Bedienungsanleitung

FuzzDog

FuzzDog Big Skweez Bedienungsanleitung

FuzzDog

FuzzDog Mutant Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Hot Snake Boost Bedienungsanleitung

FuzzDog

FuzzDog Electrica+ Bedienungsanleitung

FuzzDog

FuzzDog Toxic Minx Distortion plus Bedienungsanleitung

FuzzDog

FuzzDog FY2 Bedienungsanleitung

FuzzDog

FuzzDog PHASE 90 Bedienungsanleitung

FuzzDog

FuzzDog GimpFX Ultr-Fk Bedienungsanleitung

FuzzDog

FuzzDog KlonBuffer V3 Bedienungsanleitung

FuzzDog

FuzzDog The Wobbler Bedienungsanleitung

FuzzDog

FuzzDog RAW FUZZ V2 Bedienungsanleitung

FuzzDog

FuzzDog BrassBlender Bedienungsanleitung

FuzzDog

FuzzDog Candyman Bedienungsanleitung

FuzzDog

FuzzDog Axis Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Jordan Bosstone Bedienungsanleitung

FuzzDog

FuzzDog Ultimatum Fuzz Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung

TREX

TREX ToneBug Totenschläger Bedienungsanleitung

BBE

BBE ORANGE SQUASH Bedienungsanleitung