FuzzDog Ruby/NoisyCricket Bedienungsanleitung

Ruby / Noisy Cricket

A couple of saucy

little amps

No reproduction permitted without the express written

Important notes

If you’re usin any of our footswitch dau hterboards,

DOWNLOAD THE DAUGHTERBOARD DOCUMENT

•Download and read the appropriate build document for the daughterboard

as well as this one BEFORE you start.

•DO NOT solder the supplied Current Limiting Resistor (CLR) to the main

circuit board even if there is a place for it. This should be soldered to the

footswitch daughterboard.

POWER SUPPLY

Unless otherwise stated in this document this circuit is designed to be

powered with 9V DC.

COMPONENT SPECS

Unless otherwise stated in this document:

•Resistors should be 0.25W. You can use those with higher ratings but

check the physical size of them.

•Electrolytics caps should be at least 25V for 9V circuits, 35V for 18V

circuits. Again, check physical size if using higher ratings.

LAYOUT CONVENTIONS

Unless otherwise stated in this document, the following are used:

•Electrolytic capacitors:

Long leg (anode) to square pad.

•Diodes/LEDs:

Striped leg (cathode) to square pad. Short leg to square pad for LEDs.

•ICs:

Square pad indicates pin 1.

Schematic RUBY

R1 1 5

R2 3K9

R4 10R

C1 47n

C2 100n

C3 Empty

C4 47n

C5 Empty

C6 100n

C7 100u elec

C8 220u elec**

Q1 2N5457*

IC1 L 386-N1

VOL 10KB

GAIN 1KB

*Other FETs will work, such

as J201. This section is

working as a buffer and will

have little bearing on the

tone. Pads are provided for

through-hole or S T FETs.

**We’ve been building these

for years will 100u at the

output. It’s plenty bassy.

Schematic NOISY CRICKET

R1 1 5

R2 3K9

R4 10R

C1 47n

C2 100n

C3 100n***

C4 47n

C5 100n

C6 100n

C7 100u elec

C8 220u elec**

Q1 2N5457*

IC1 L 386-N1

VOL 10KB

GAIN 1KB

TONE 100KB***

GRIT SPDT ON-ON

*Other FETs will work, such

as J201. This section is

working as a buffer and will

have little bearing on the

tone. Pads are provided for

through-hole or S T FETs.

**We’ve been building these

for years will 100u at the

output. It’s plenty bassy.

***To build it without the

tone control simply leave out

these parts.

No jumpers required.

Be very careful when soldering Q1. FETs are very

sensitive to heat. You should use some kind of

heat sink (crocodile clip or reverse action

tweezers) on each leg as you solder them. Keep

exposure to heat to a minimum (under 2

seconds). Same goes for the IC if you aren’t

using a socket.

You need to remove anything that’s sticking out

of the 9mm pot other than the three PCB pins. It

should snip off easily with wire cutters.

You should solder all other board-mounted

components before you solder the pots. Once

they’re in place you’ll have no access to much of

the board. ake sure your pots all line up nicely.

The best way to do that is to solder

a single pin of each pot in place then melt and

adjust if necessary before soldering in the other

two pins. Don’t push the pins all the way into the

PCB - give yourself 1-2mm of wiggle room on

the pot height if you’re going to be adding the

toggle switch.

If you’re wiring your pots, the square pad is pin 1.

These need to o away.

Enclosure layout

Of course you can lay it out however you like, but it was designed for this configuration in a 1590B.

Wiring

This configuration, using a TRS input jack, will disconnect the battery when the

jack is unplugged. However, if you have a DC supply connected it will be on all the

time. You can add an on/off switch inline with the ground wire between the DC

socket and the PCB - see bottom.

18mm15mm

22mm21mm

21mm 21mm

18mm

Drilling guides - 1590B

Pots are 7mm, toggle switch is 6mm. However, adding 1mm to each will make for less

headaches when boxing up your circuit.

Jacks are normally 10mm, DC socket is 12mm.

This layout will give you space between the DC and output jack to fit a PP3 battery.

This templates are rough guides only. You should ensure correct marking of your

enclosure before drilling. You use this template at your own risk.

Pedal Parts Ltd can accept no responsibility for incorrect drilling of enclosures.

FuzzDog.co.uk

Inhaltsverzeichnis

Andere FuzzDog Musikpedal Handbücher

FuzzDog

FuzzDog FY2 Bedienungsanleitung

FuzzDog

FuzzDog Flender Bedienungsanleitung

FuzzDog

FuzzDog Shin-Ei FY2 Companion Fuzz Bedienungsanleitung

FuzzDog

FuzzDog PHASE 90 Bedienungsanleitung

FuzzDog

FuzzDog Electrica+ Bedienungsanleitung

FuzzDog

FuzzDog Gristleiser Bedienungsanleitung

FuzzDog

FuzzDog Big Skweez Bedienungsanleitung

FuzzDog

FuzzDog SweetyPuss Bedienungsanleitung

FuzzDog

FuzzDog Hot Snake Boost Bedienungsanleitung

FuzzDog

FuzzDog Filth Fack! Bedienungsanleitung

FuzzDog

FuzzDog Animatron Bedienungsanleitung

FuzzDog

FuzzDog MicrAmp Bedienungsanleitung

FuzzDog

FuzzDog Mutant Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Rodent Bedienungsanleitung

FuzzDog

FuzzDog GimpFX Ultr-Fk Bedienungsanleitung

FuzzDog

FuzzDog Repeater V4 Bedienungsanleitung

FuzzDog

FuzzDog 7 of Dwarves Auto Wah Bedienungsanleitung

FuzzDog

FuzzDog RockBox Bedienungsanleitung

FuzzDog

FuzzDog Super Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Amber Chuck V4 Bedienungsanleitung

FuzzDog

FuzzDog Cocoon Bedienungsanleitung

FuzzDog

FuzzDog Tube Screamer v4.0 Bedienungsanleitung

FuzzDog

FuzzDog Axis Fuzz Bedienungsanleitung

FuzzDog

FuzzDog Clay Jones OD V2 Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung

TREX

TREX ToneBug Totenschläger Bedienungsanleitung

BBE

BBE ORANGE SQUASH Bedienungsanleitung