Hach SIP 10 kit Bedienungsanleitung

DOC272.97.80548

SIP 10 kit for TL23xx

02/2017, Edition 1

User Instructions

Instructions d'utilisation

Instrucciones para el usuario

Instruções do Usuário

用户说明

取扱説明書

사용자 지침

คำแนะนำในการใช้งาน

English..............................................................................................................................3

Français......................................................................................................................... 17

Español.......................................................................................................................... 31

Português...................................................................................................................... 45

中文................................................................................................................................. 59

日本語............................................................................................................................. 72

한글................................................................................................................................. 85

ไทย.................................................................................................................................... 98

Table of contents

Specifications on page 3 Maintenance on page 12

General information on page 3 Troubleshooting on page 15

Installation on page 7 Replacement parts and accessories on page 15

Operation on page 10

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions (W x D x H) Sipper unit: 120 x 85 x 200 mm (4.7 x 3.4 x 7.9 in.)

Enclosure IP30

Weight Sipper unit: 0.5 kg (1.1 lb)

Protection class II

Pollution degree 2

Installation category I

Power supply Power is supplied by the turbidimeter through the USB cable, 530 mA, 5 V

Operating temperature 10 to 40 °C (50 to 104 °F)

Storage temperature –10 to 60 °C (14 to 140 °F)

Humidity 80% relative humidity, non-condensing

Rinsing agent 120 mL minimum to remove sample from the tubing

Flow speed 1 mL/sec

Sample temperature 2 to 70 °C (35.6 to 158 °F)

Sample salt content 65 g/L maximum

Interface USB

Certifications CE

Warranty 1 year (EU: 2 years)

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

English 3

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This symbol, if noted on the instrument, references the instruction manual for operation and/or safety

information.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

Certification

Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

4 English

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

Product overview

WARNING

Fire hazard. This product is not designed for use with flammable liquids.

CAUTION

Chemical exposure hazard. Dispose of chemicals and wastes in accordance with local, regional and

national regulations.

The SIP 10 sipper kit for the TL23xx turbidimeter is used to pull a selected quantity of a water sample

through the flow cell in the TL23xx before each turbidity measurement. Refer to Figure 1. If selected,

the sipper pulls a selected quantity of a user-supplied rinse agent through the flow cell after each

turbidity measurement.

English 5

Figure 1 Product overview

1 USB cable 4 Flow cell 7 Sample source

2 TL23xx turbidimeter 5 Flow cell assembly 8 SIP 10 sipper unit

3 Flow cell cover 6 Drain 9 Peristaltic pump

Product components

Make sure that all components have been received. Refer to Figure 2. If any items are missing or

damaged, contact the manufacturer or a sales representative immediately.

6 English

Figure 2 Product components

1 USB cable, type AB, 1 m (3.3 ft) 7 Flow cells (2x)

2 Tygon® tubing, 1/8-in. ID, 1.70 m (5.6 ft) 8 Bottom cap with O-ring

3 Flow cell cover 9 Y fitting for 1/8-in. ID tubing

4 Flow cell assembly 10 Flow cell frame

5 Top cap with O-ring 11 SIP 10 sipper unit

6 Replacement O-rings (2x)

Installation

Clean and install the flow cell assembly

N O T I C E

Do not to touch or scratch the flow cell. Contamination or scratches on the glass can cause measurement errors.

1. Clean the flow cell assembly. Do steps 2 to 4 of Clean the flow cell assembly on page 12.

2. Install the flow cell assembly as shown in the illustrated steps that follow.

Note: Keep the tubing as short as possible to minimize air locking and lag time of the sample flow.

At step 4 of the illustrated steps, apply silicone oil to the flow cell as follows:

a. Apply a small drop of silicone oil from the top to the bottom of the flow cell.

Note: Use only the provided silicone oil. This silicone oil has the same refractive index as the flow cell glass

and masks minor glass scratches.

b. Use the oiling cloth to apply the oil equally to the surface of the flow cell. Remove most of the

oil. Make sure that the vial is almost dry.

Note: Put the oiling cloth in a plastic storage bag to keep the cloth clean.

English 7

8 English

English 9

Connect the USB cable

Connect the USB cable. Refer to the illustration that follows.

Operation

Configure the settings

1. Connect the turbidimeter power cable to an electrical outlet.

2. Push the power button to set the turbidimeter to on.

3. Push Sipper.

10 English

Inhaltsverzeichnis

Sprachen:

Andere Hach Laborausrüstung Handbücher

Hach

Hach POCKET COLORIMETER II Bedienungsanleitung

Hach

Hach ISECL181 Bedienungsanleitung

Hach

Hach sensION MM340 Bedienungsanleitung

Hach

Hach HQ440d Bedienungsanleitung

Hach

Hach 2100N Kurzanleitung

Hach

Hach Lachat BD40HT Bedienungsanleitung

Hach

Hach MTC10101 Bedienungsanleitung

Hach

Hach PHC745 Bedienungsanleitung

Hach

Hach BODTrak Bedienungsanleitung

Hach

Hach TitraLab Bedienungsanleitung

Hach

Hach GANIMEDE P Bedienungsanleitung

Hach

Hach TU5200 Bedienungsanleitung

Hach

Hach CDC401-01 Bedienungsanleitung

Hach

Hach TenSette 19700-01 Bedienungsanleitung

Hach

Hach sensIONTM+ pH31 Bedienungsanleitung

Hach

Hach BOD Direct plus Kurzanleitung

Hach

Hach ISENH4181 Bedienungsanleitung

Hach

Hach ISEF121 Series Bedienungsanleitung

Hach

Hach PHC705 Bedienungsanleitung

Hach

Hach TitraLab AT1000 Series Kurzanleitung

Hach

Hach TitraLab Kurzanleitung

Hach

Hach POCKET TURBIDIMETER Bedienungsanleitung

Hach

Hach LQV157.99.50001 Bedienungsanleitung

Hach

Hach QuikChem 8500 2 Series Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung