Hach PHC301 Bedienungsanleitung

DOC022.53.80032

PHC301

05/2021, Edition 3

User Manual

Table of Contents

Section 1 Product overview................................................................................. 3

Section 2 Specifications........................................................................................ 3

Section 3 Safety information............................................................................... 4

3.1 Intended use ....................................................................................................... 4

3.2 Use of hazard information..................................................................................... 4

3.3 Precautionary labels............................................................................................. 5

3.4 Product hazards.................................................................................................... 5

Section 4 Preparation for use.............................................................................. 5

Section 5 Calibration.............................................................................................. 7

5.1 Calibration notes................................................................................................... 7

5.2 Calibration procedure........................................................................................... 8

Section 6 Sample measurement ...................................................................... 9

6.1 Sample measurement notes................................................................................. 9

6.2 Sample measurement procedure......................................................................... 9

Section 7 Verify the calibration........................................................................ 10

7.1 Verification procedure......................................................................................... 10

Section 8 Maintenance........................................................................................ 11

8.1 Clean the probe.................................................................................................. 11

8.2 Fill the probe....................................................................................................... 12

8.3 Replace the filling solution.................................................................................. 12

8.4 Soak procedure for dry probes........................................................................... 12

8.5 Storage............................................................................................................... 13

Section 9 Troubleshooting ............................................................................... 14

Section 10 Consumables..................................................................................... 15

10.1 Recommended standards................................................................................. 15

10.2 Accessories...................................................................................................... 16

Table of Contents

Section 1 Product overview

The Intellical PHC301 series pH probes are digital, combination electrodes that measure the pH of

wastewater, drinking water and general water samples. The probes are refillable and have a built-in

temperature sensor and a double ceramic pin for a reference junction. A 28-mL bottle of reference

electrolyte filling solution is supplied with the probe. Refer to Figure 1.

Note: Do not use the probe for measurements in organic solvents.

Figure 1 Probe overview

1 Probe soaker bottle with storage solution 5 Cable

2 Glass bulb, reference junction and

temperature sensor

6 Probe soaker bottle holder

3 Filling-hole plug 7 Electrode filling and storage solution

4 Protective tape and filling hole

Section 2 Specifications

Specifications are subject to change without notice.

Specifications Details

Probe type Digital combination pH probe with refillable electrolyte and built-in

temperature sensor

pH range 0 to 14 pH

pH accuracy ±0.02 pH

Reference type Ag/AgCl

Reference junction Double ceramic porous pin

Slope –59 mV/pH (90 to 110% at 25 °C (77 °F) per Nernstian theoretical

value)

Isopotential point 0 (±30) mV at 7.0 (±0.5) pH

Sodium (alkalinity) error –0.6 pH at pH 12.6 in 1 M NaOH

Temperature accuracy ±0.3 °C (±0.54 °F)

Temperature sensor type 30 kΩ NTC thermistor

Operating temperature 0 to 50 °C (32 to 122 °F)

English 3

Specifications Details

Storage temperature 5 to 40 °C (41 to 104 °F)

Minimum immersion depth 15 mm (0.59 in.)

Body material (standard) Zeonor™

Electrolyte filling solution 3 M KCl saturated with AgCl

Storage solution Hach pH electrode storage solution1 or 3 M KCl

Cable connection M12 digital output and connector

Dimensions Diameter: 12 mm (0.47 in.)

Length: 175 mm (6.9 in.) total; 103 mm (4.1 in.) below head

Cable length: PHC30101: 1 m (3.3 ft); PHC30103: 3 m (9.8 ft)

Weight (includes cable) PHCxxx01: ~0.4 kg (0.9 lb); PHCxxx03: ~0.45 kg (1 lb)

Warranty 6 months on the probe. This warranty covers manufacturing defects,

but not improper use or wear.

Certifications CE, FCC/ISED

Section 3 Safety information

3.1 Intended use

The Intellical probes are intended for use by individuals who measure water quality parameters in the

laboratory. The Intellical probes do not treat or alter water.

3.2 Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that

requires special emphasis.

1Use of other storage solutions can cause permanent damage to the probe.

4 English

3.3 Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

Electrical equipment marked with this symbol may not be disposed of in European

domestic or public disposal systems. Return old or end-of-life equipment to the

manufacturer for disposal at no charge to the user.

3.4 Product hazards

CAUTION

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the

personal protective equipment appropriate to the chemicals that are handled. Refer to

the current safety data sheets (MSDS/SDS) for safety protocols.

CAUTION

Chemical exposure hazard. Dispose of chemicals and wastes in accordance with local,

regional and national regulations.

CAUTION

Personal injury hazard. Glass components can break. Handle with care to prevent cuts.

Section 4 Preparation for use

N O T I C E

Make sure to remove the protective tape from the filling hole of new probes. A probe with a blocked

filling hole will not operate correctly.

New probes are filled with electrolyte filling solution and have a soaker bottle that contains storage

solution to keep the glass bulb and reference junction hydrated. Prepare the probe for calibration and

measurement as follows.

1. Remove the protective tape from the filling hole. Refer to Figure 2.

2. Rinse the reference junction and glass bulb with deionized water. Blot dry with a lint-free cloth.

3. If the inner filling solution is low, add more filling solution. Refer to Fill the probe on page 12.

4. Make sure that the meter has the correct date and time settings. The service-life time stamp in

the probe comes from the date and time settings in the meter.

Note: Some meters automatically open the date and time settings when the meter starts for the first time, or

after battery replacement.

5. Connect the probe to the meter.

6. Open the filling hole before use. Keep the level of the electrolyte filling solution above the level of

the measurement liquid during use. Refer to Figure 3.

Note: For faster stabilization, soak the probe for 3 or more minutes in the sample before use.

English 5

Figure 2 Remove the protective tape

6 English

Figure 3 Probe position during use

1 Open filling hole 3 Level of calibration solution or sample

2 Level of electrolyte filling solution

Section 5 Calibration

The procedure that follows is applicable to meters that can connect to Intellical pH probes. Refer to

the applicable meter documentation for meter operation and probe-specific settings.

5.1 Calibration notes

Read the notes that follow before calibration:

• Use prepared pH buffer solutions or mix pH buffer powder pillows with deionized water for

calibration. Discard the prepared buffer solutions after each calibration.

• Use two or three buffer solutions for best results. Two buffer solutions are sufficient if the expected

sample pH is between the pH of the two buffer solutions. The sequence in which the pH buffer

solutions are used is not important. Use buffer solutions that are 2 or more pH units apart.

• For a one-point calibration, use a pH buffer near the expected sample pH.

• Use the default calibration options or change the options in the probe settings menu.

• Use the single display mode for calibration when more than one probe is connected to the meter (if

applicable).

• Calibrate the probes and verify the calibration regularly for best results. Use the meter to set

calibration reminders.

• The calibration data is stored in the probe. When a calibrated probe is connected to a different

meter with the same calibration options, a new calibration is not necessary.

• Air bubbles below the sensor when in solution can cause a slow response or error in the

calibration. Make sure to remove air bubbles during calibration.

• The pH buffer solutions have known pH values at different temperatures. The meter uses the mV

and temperature readings of the probe in the pH buffer solutions to calculate a calibration slope.

During measurements, the meter adjusts the slope for the sample temperature to determine the

pH value of the sample.

English 7

5.2 Calibration procedure

1. Go to the

calibrate menu.

Select the probe, if

applicable. The

display shows the

pH buffer solutions

to use for calibration.

2. Prepare or pour

the pH buffer

solutions in different

beakers.

3. Open the filling

hole.

4. Rinse the probe

with deionized water.

Dry the probe with a

lint-free cloth.

5. Put the probe in

the first pH buffer

solution. Make sure

that the sensor and

reference junction

are fully in the

solution. Do not put

the probe on the

bottom or sides of

the beaker.

6. Shake the probe

from side to side to

refresh the reference

junction and remove

air bubbles.

7. Stir slowly, then

read the pH value of

the buffer solution.

The display shows

the temperature-

corrected pH value

when the reading is

stable.

8. Continue with

steps 4 through 7 for

the remaining

buffers or select

Done.

9. Save the

calibration.

8 English

Inhaltsverzeichnis

Andere Hach Laborausrüstung Handbücher

Hach

Hach BOD Direct plus Kurzanleitung

Hach

Hach AS950 AWRS Bedienungsanleitung

Hach

Hach DRB 200 Bedienungsanleitung

Hach

Hach sensION MM340 Bedienungsanleitung

Hach

Hach TitraStir 19400-00 Bedienungsanleitung

Hach

Hach sensION+ EC7 Bedienungsanleitung

Hach

Hach TitraLab Bedienungsanleitung

Hach

Hach LZV902 Bedienungsanleitung

Hach

Hach Debubb Bedienungsanleitung

Hach

Hach TitraLab Kurzanleitung

Hach

Hach POCKET TURBIDIMETER Bedienungsanleitung

Hach

Hach LOC 100 Bedienungsanleitung

Hach

Hach 2100AN IS Kurzanleitung

Hach

Hach PHOSPHAX sigma High Range Bedienungsanleitung

Hach

Hach DR 5000 Bedienungsanleitung

Hach

Hach LS 120 Bedienungsanleitung

Hach

Hach ISEF121 Series Bedienungsanleitung

Hach

Hach BODTrak II Kurzanleitung

Hach

Hach 2100AN IS Bedienungsanleitung

Hach

Hach SD900 Kurzanleitung

Hach

Hach ORBISPHERE 29122 Bedienungsanleitung

Hach

Hach MTC10101 Bedienungsanleitung

Hach

Hach POCKET COLORIMETER II Bedienungsanleitung

Hach

Hach TitraLab Total Hardness Kurzanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung