Handicare SystemRoMedic Vega505EE Bedienungsanleitung

User manual – English

Manual nr: 630 Rev 12

SWL: 230 kg / 505 Ibs

DETAIL A

SCALE 1 : 5

No burrs allowed

Break sharp edges: Rmax:0.3 mm / 0.3 mmx 45degrees

Replaces drawing/part number (Linido Part No)

Unless otherwise stated, general tolerances according to ISO 2768-m

Omitted dimensions according to

[60600003_03_Vega505EE.dwg/step]

REVISION HISTORY

REV.

POS.

DESCRIPTION

DATE

DRAWN BY

Art. no.

extension

RAL code

Color

Stainless steel polished

Blanc

RAL 9010

White

RAL9005

Black

RAL3003

Red

RAL5002

Blue

RAL9001

Créme white

09 (special)

Divers

Color

This drawing and any information or descriptive matter set out hereon are the confidential and copyright property of Handicare

and must not be disclosed, loaned, copied or used for manufacturing, tendering or any other purpose without their written permission.

SCALE

PROJECTION

MATERIAL SPECIFICATION:

2015-03-02

60600003

Vega505EE

Released

SIZE

MATERIAL:

TITLE

STATUS

WEIGHT:

SHEET 1 OF 1

CREATED

DATE

NAME

REV.

DWG. NO.

1:20

hc-makn

Vega505EE

60600003

SystemRoMedicTM

English

Vega505EE is a mobile patient lift adapted for safe and easy lifting of users weighing up to 230 kg/505 lbs. Vega505EE

features a unique design with a lift arm that can be both raised to an almost upright position and lowered all the way

down to the floor. It is also relatively narrow and compact, with dimensions adapted for use in premises and situations

where space is limited. In spite of the handy size, Vega505EE offers an unusually high lifting height and an extremely

large lifting range. Therefore, the lift can manage all lifting situations and requirements; both low and high lifting, seated or

supine, to and from the floor, bed or chair, and gait training.

1. Lift arm

2. Mast

3. Handlebar

4. Emergency stop

5. Control box / Battery pack

6. Motor for base-width adjustment

7. Rear castors with brakes

8. Sling bar with safety latches

9. Front castors

10. Emergency lowering

11. Motor/actuator for lift arm

12. Hand control

REVISION HISTORY

REV.

DESCRIPTION

DATE

APPROVED

SCALE:1:20

DWG. NO.

REV.

NAME

DATE

DRAWN

APPROVED BY

SHEET 1 OF 1

WEIGHT:

COMMENTS:

STATUS:

TITLE

MATERIAL:

SIZE

Released

Vega505EE

60600003 02

2014-09-25

Unless otherwise stated, general

tolerances according to ISO 2768-m

139402makn@z40

This drawing and any information or descriptive matter set out hereon are the confidential and copyright property of Handicare

and must not be disclosed, loaned, copied or used for manufacturing, tendering or any other purpose without their written permission.

Vega505EE

Visual inspection

Inspect lift functions regularly. Check to ensure that material is free from damage.

Before use

Make certain the lift is properly assembled.

Check sling bar connection and safety latch function.

Check lifting function and base-width adjustment.

Check to ensure that the quick-connecting locking pin for the actuator is correctly installed.

Safety information

Always read the user manuals for all assistive devices used during a transfer.

Keep the user manual where it is accessible to users of the product.

Always make sure that you have the right version of the user manual.

Under no circumstances may the lift be used by persons who have not received instruction in the operation of the lift.

It is strongly prohibited to modify the original product.

Always read the user manual

SystemRoMedicTM

4USER MANUAL SystemRoMedicTM

English

Assembly

Check to ensure that the following components are included

Mast and lift arm, actuator, slingbar, control box, hand control.

Undercarriage with base-width adjustment motor, screws,

washers, nuts and screw covers.

User manual and charger.

Insert the mast onto the base. Assemble according to illustration A and tighten it

hard (>60 Nm). Place the screw covers over the screws.

Place the battery in the mount in the control box.

Connect the cables: The cable for the hand control in outlet HS; the cable for the

hoist motor in outlet M1, and the cable for the base motor in outlet M2.

Release the emergency stop and perform a final inspection (see final inspection).

DETAIL A

SCALE 1 : 5

No burrs allowed

Break sharp edges: Rmax:0.3 mm / 0.3 mmx 45degrees

Replaces drawing/part number (Linido Part No)

Unless otherwise stated, general tolerances according to ISO 2768-m

Omitted dimensions according to

[60600003_03_Vega505EE.dwg/step]

REVISION HISTORY

REV.

POS.

DESCRIPTION

DATE

DRAWN BY

Art. no.

extension

RAL code

Color

Stainless steel polished

Blanc

RAL 9010

White

RAL9005

Black

RAL3003

Red

RAL5002

Blue

RAL9001

Créme white

09 (special)

Divers

Color

This drawing and any information or descriptive matter set out hereon are the confidential and copyright property of Handicare

and must not be disclosed, loaned, copied or used for manufacturing, tendering or any other purpose without their written permission.

SCALE

PROJECTION

MATERIAL SPECIFICATION:

2015-03-02

60600003

Vega505EE

Released

SIZE

MATERIAL:

TITLE

STATUS

WEIGHT:

SHEET 1 OF 1

CREATED

DATE

NAME

REV.

DWG. NO.

1:20

hc-makn

DETAIL A

SCALE 1 : 5

No burrs allowed

Break sharp edges: Rmax:0.3 mm / 0.3 mmx 45degrees

Replaces drawing/part number (Linido Part No)

Unless otherwise stated, general tolerances according to ISO 2768-m

Omitted dimensions according to

[60600003_03_Vega505EE.dwg/step]

REVISION HISTORY

REV.

POS.

DESCRIPTION

DATE

DRAWN BY

Art. no.

extension

RAL code

Color

Stainless steel polished

Blanc

RAL 9010

White

RAL9005

Black

RAL3003

Red

RAL5002

Blue

RAL9001

Créme white

09 (special)

Divers

Color

This drawing and any information or descriptive matter set out hereon are the confidential and copyright property of Handicare

and must not be disclosed, loaned, copied or used for manufacturing, tendering or any other purpose without their written permission.

SCALE

PROJECTION

MATERIAL SPECIFICATION:

2015-03-02

60600003

Vega505EE

Released

SIZE

MATERIAL:

TITLE

STATUS

WEIGHT:

SHEET 1 OF 1

CREATED

DATE

NAME

REV.

DWG. NO.

1:20

hc-makn

DETAIL A

SCALE 1 : 5

No burrs allowed

Break sharp edges: Rmax:0.3 mm / 0.3 mmx 45degrees

Replaces drawing/part number (Linido Part No)

Unless otherwise stated, general tolerances according to ISO 2768-m

Omitted dimensions according to

[60600003_03_Vega505EE.dwg/step]

REVISION HISTORY

REV.

POS.

DESCRIPTION

DATE

DRAWN BY

Art. no.

extension

RAL code

Color

Stainless steel polished

Blanc

RAL 9010

White

RAL9005

Black

RAL3003

Red

RAL5002

Blue

RAL9001

Créme white

09 (special)

Divers

Color

This drawing and any information or descriptive matter set out hereon are the confidential and copyright property of Handicare

and must not be disclosed, loaned, copied or used for manufacturing, tendering or any other purpose without their written permission.

SCALE

PROJECTION

MATERIAL SPECIFICATION:

2015-03-02

60600003

Vega505EE

Released

SIZE

MATERIAL:

TITLE

STATUS

WEIGHT:

SHEET 1 OF 1

CREATED

DATE

NAME

REV.

DWG. NO.

1:20

hc-makn

HS M1 M2

USER MANUAL

SystemRoMedicTM

Final inspection

Check to ensure that no parts have been left in the packaging.

Inspect the lift for signs of wear and damage.

Check all four castor wheels and castor wheel locks.

Check all connections and fixtures including screws and bolts.

Check the emergency stop function by activating the emergency stop button, and

then pressing either the up or down button. If nothing happens when the up or down

buttons are pressed, the emergency stop is functioning properly.

Grasp the hand control, press the up button and run the lift arm all the way up. Then,

press the down button and run the lift arm all the way down.

Test base-width adjustment function. Press the button for base-width adjustment to

widen the base fully, and then press the other button to narrow the base again.

Test lift function by lifting a person (not a user) using an approved sling. At the same

time, check the emergency lowering function with someone on the lift. See section on

Emergency lowering.

If the lift is functioning correctly, connect the charger and check to ensure that the

charging lamp on the control box lights up.

NOTE!

Before the lift is used for the first time:

• it must be charged for at least 4 hours. See section on charging batteries.

• the control box service counter needs to be reset. To reset the service counters

press both lift buttons on the hand control at the same time for 5 seconds.

An audio signal will indicate that the timer has been reset.

Keep the user manual where it is accessible to users of the product.

6USER MANUAL SystemRoMedicTM

English

Using the product

Safe working load

Different products on the same lift system (lift unit, slingbar, sling and other lifting accessories) may have different al-

lowable safe working loads. The lowest allowable safe working load always determines the safe working load of the

assembled system. Always check the safe working loads for the lift and accessories before use. Contact your dealer if

you have any questions.

Important Information

• The lift must be assembled according to the instructions provided by Handicare.

• The lift may only be used indoors and on a level floor.

• Lifting accessories must be properly fitted and tested in relation to the user’s needs and functional ability.

• Do not leave the user unattended during a transfer situation.

• Under no circumstances may the safe working load be exceeded. See section on Safe Working Load.

• Never move the lift by pulling on the actuator!

• The lift must not be used or immersed in or under water including showering.

• The lift should not be left / stored in a high humidity environment.

• The lift must not be charged in a wet room.

• To ensure optimal function, the lift must be inspected regularly. See section on other maintenance details.

• Warranty applies only if repairs or alterations are made to the product by personnel who are authorized by Handicare.

• Using lifting accessories other than those approved can entail a risk.

• Note that there is a pinch point between the manual emergency lowering mechanism and the lift arm when

the lift arm is in its highest and lowest positions.

• Verify that all lifting accessories hang vertically and can move freely.

USER MANUAL

SystemRoMedicTM

Battery information on the display

The battery discharging will be shown in four stages:

Battery state 1: The battery is ok, no need for charging (100 - 50 %).

Battery state 2: Battery needs charging. (50 - 25 %)

Battery state 3: Battery needs charging. (Less than 25 %) A tone sounds when a button is pressed in

this battery state.

Battery state 4: The battery needs charging. (17V or lower) At this stage some of the functionality of the

lift is lost.At this battery stage it is only possible to drive the lift arm down. Furthermore an audio signal

will sound when a control button is activated. The symbol will switch between the two pictures for 10

seconds.

The battery symbol is shown when the control box is active until power down (2 minutes after use).

It is not possible to use other batttery types than BAJ1/BAJ2.

The battery level is measured via voltage. This means that it is possible to experience e.g. that the

battery switches from state 1 to state 2 and back to state 1.

Charging batteries

A tone sounding when using the lift indicates that the battery need recharging.

Charge the lift after use to ensure that the battery is always fully charged.

Lock the castor wheels when charging the battery.

1. Connect the charging cable to a power outlet and in the connection for charger cable.

The symbol for charging is shown on the display.

2. Check to ensure that the lamps on the control box light up. The green LED lamp indicates that the

charger is receiving power and the yellow LED lamp indicates that the battery is charging.

3. Charging stops automatically when the battery is fully charged.

Wall-mounted charger

1. Remove the battery pack from the lift and place it in the wall-mounted charger.

2. Check to ensure that the LED lamp on the front of the charger lights up.

NOTE!

Before the lift is used for the first time, it must be charged for at least 4 hours.

For maximum battery life, charge batteries regularly. We recommend daily charging when the lift is

used daily.

The emergency stop must be deactivated during charging.

8USER MANUAL SystemRoMedicTM

English

Eva450EEL Eva600EEL

Eva450EML

REVISION HISTORY

REV.

DESCRIPTION

DATE

APPROVED

SCALE:1:10

DWG. NO.

REV.

NAME

DATE

DRAWN

APPROVED BY

SHEET 1 OF 1

WEIGHT:

COMMENTS:

STATUS:

TITLE

MATERIAL:

SIZE

Released

EVA EEL 450 base

90001288 02

2011-05-20

Unless otherwise stated, general

tolerances according to ISO 2768-m

hc-jope

This drawing and any information or descriptive matter set out hereon are the confidential and copyright property of Handicare

and must not be disclosed, loaned, copied or used for manufacturing, tendering or any other purpose without their written permission.

Service information read-out

Basic service information can be read out on the display. To get the service information on the

display please press the lift arm up button for half a second. The information will be shown for

½ minute or until other buttons are activated.

• Total cycles done by the actuator

• Total work done by the actuator (ampere usage times seconds in use)

• Total number of overloads

• Days since last service/Days between services

Hand control

Raising/lowering the lift arm

Symbol indicate direction of travel.

Motion stops as soon as the button is released.

If the lift arm encounter an obstacle while lowering, the lift will

immediately stop the motion. In order to continue, the lift arm will

need to be raised slightly by using the hand control before further lowering.

Electrical base-width adjustment (EE)

Markings on the buttons of the hand control indicate function.

Motion stops as soon as the buttons are released.

Changing the battery

”Click!”

USER MANUAL

SystemRoMedicTM

Emergency stop

To activate emergency stop

Depress the red emergency stop button on the control box.

Resetting

Turn the button in the direction of the arrows until the button pops out.

To prevent battery discharge, we recommend that the emergency-stop button is pressed in

when the lift is not in use.

Emergency lowering

Manual emergency lowering

For manual emergency lowering, turn the round plastic knob on the actuator clockwise.

Electrical emergency lowering

For electrical emergency lowering, puch the down button on the control box. Use a narrow

object such as a pen.

Trouble shooting

If the lift or base-width adjustment cannot be activated, check the following:

- That the emergency stop button is not pressed in.

- That all cables are properly and securely connected. Pull out the contact and plug it in again firmly.

- That battery charging is not in progress.

- That the battery is charged.

If the lift is not working properly, contact your dealer.

If the lift makes unusual noises:

- Try to determine the source of the sound. Take the lift out of operation and contact your dealer.

10 USER MANUAL SystemRoMedicTM

English

Accessories

Lifting slings

Handicare’s SystemRoMedic™ line includes a wide range of functional and comfortable,

high-quality lifting slings that are adapted for all types of lifting and for users with different

needs. The lifting slings are available in several materials and in sizes ranging from XXS to

XXL. There are also special lifting sling models in XXXL and XXXXL for extremely large and

heavy users. All models are safe and very easy to use.

Sling bars

SlingBar is a two-point aluminium sling bar available in four variants with different width. All

variants of SlingBar have safety latches which prevent the sling straps from creeping out of

the sling bar and all variants are for users weighing up to 300 kg/660 lbs.

To get more room in a lifting sling when using SlingBar two-point sling bar, SlingBarSpreader

M side bars can be used as an accessory. SlingBarSpreader M open up the lifting sling and

provide for a more reclined position.

SlingBar XS article no.: 70200071

SlingBar S article no.: 70200001

SlingBar M article no.: 70200002

SlingBar L article no.: 70200003

SlingBarSpreader M article no.: 70200042

StretcherBar, article no.: 70200006, and StretcherSling, article no.: 46502007, for lifting in a

supine position.

Sling bar RFL X4, Article no.: 70200017, is a four-poinr sling bar designed to provide more

space in the sling, for example, for obese and/or pain-sensitive users.

SwiftHook for sling bar article no.: 70200008

Hand control

Hand control HB33-6, article no.: 70200089, with service, battery status and overload

indicator.

Scales

Charder MHS2500 is used together with a stationary or mobile lift for weighing of users.

Article no.: 70100002, SWL: 300kg/660lbs

Article no.: 70200003, SWL: 400kg/880lbs

Assistive devices for positioning

Handicare´s SystemRoMedic™ range includes a wide selection of functional, comfortable,

high-quality assistive devices for positioning that can be adapted for different types of lifting

and for users with different needs.

USER MANUAL

SystemRoMedicTM

Maintenance

The lift must undergo thorough inspection at least once per year. Inspection must be performed by authorized personnel

and in accordance with Handicare’s service manual.

Repairs and maintenance may only be done by authorized personnel using original spare parts.

Used batteries are to be left at the nearest recycling station. Used batteries can also be returned to

Handicare or a Handicare dealer for recycling.

+50 ºC

-10 ºC

Cleaning/disinfection

If necessary, clean the lift with warm water or a soap solution and check that the castors are free from dirt and hair. Do

not use cleaning agents containing phenol or chlorine, as this could damage the aluminium and the plastic materials. If

disinfection is needed, 70 % ethanol, 45 % isopropanol or similar should be used.

Storage and transportation

If the lift is not to be used for some time or e.g., during transport, we recommend that the emergency stop button be

pressed in. The hoist should be transported and stored in -10 ° C to + 50 ° C and in normal humidity, 30% -75 %.

The air pressure should be between 700 and 1060 hPa. Let the hoist reach room temperature before the batteries are

charged or the hoist is used.

Service agreements

Handicare offers the possibility of service agreements for maintenance and regular testing of your mobile lift. Contact

your local Handicare representative.

106 kPa

70 kPa

75%

30%

1060 hPa

700 hPa

+50 °C

-10 °C

75%

30%

12 USER MANUAL SystemRoMedicTM

Andere Handbücher für SystemRoMedic Vega505EE

Inhaltsverzeichnis

Andere Handicare Medizinische Geräte Handbücher

Handicare

Handicare SystemRoMedic SoftLegSupport Bedienungsanleitung

Handicare

Handicare SystemRoMedic TurnTable Bedienungsanleitung

Handicare

Handicare SystemRoMedic EasyBelt Bedienungsanleitung

Handicare

Handicare SystemRoMedic EasyBelt Bedienungsanleitung

Handicare

Handicare LI2610.0010-00 Bedienungsanleitung

Handicare

Handicare MiniLift160 Classic Bedienungsanleitung

Handicare

Handicare MiniLift125 Bedienungsanleitung

Handicare

Handicare LinidoSolutions LI2403.150 Series Bedienungsanleitung

Handicare

Handicare LI2613.000 Series Bedienungsanleitung

Handicare

Handicare SystemRoMedic SupportStraps Bedienungsanleitung

Handicare

Handicare LI2214.201 Series Bedienungsanleitung

Handicare

Handicare Micro Pilot Joystick Bedienungsanleitung

Handicare

Handicare SitWalk Bedienungsanleitung

Handicare

Handicare SystemRoMedic ReTurnBelt Bedienungsanleitung

Handicare

Handicare SystemRoMedic RiseAtlas450 Bedienungsanleitung

Handicare

Handicare SystemRoMedic AmpSling Series Bedienungsanleitung

Handicare

Handicare SitWalk Bedienungsanleitung

Handicare

Handicare SystemRoMedic WendyLett Bedienungsanleitung

Handicare

Handicare LI3012.0004-02 Bedienungsanleitung

Handicare

Handicare 3309320 Bedienungsanleitung

Handicare

Handicare SystemRoMedic SoftLegSupport Bedienungsanleitung

Handicare

Handicare SystemRoMedic EvaDrive Bedienungsanleitung

Handicare

Handicare 201903314 Bedienungsanleitung

Handicare

Handicare Eva400 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung