Honeywell ExiLED Bedienungsanleitung

ExiLED

Surface Mounted

Installation:

Dimensional Drawings:

266mm

132mm

223mm

53mm

ExiLED 25m 366mm

199mm

289mm

53mm

ExiLED 40m

Step 1: For double sided pictogram, install the appropriate pictograms to both sides, push up until you

hear click sound. For single sided pictogram, there is one blind pictogram in the package.

Step 4. Drill a hole on a black grommet and pass the mains cables through it. Connect the mains cables to

terminal blocks: L for live wire, N for neutral and PE for ground. Power supply cables cross section

should be 0.8 - 3 mm . The C1 and C2 terminals are used for elBus communication optional), DALI

communication (optional), or voltage free contact (optional). Tighten the cable tie around the

cables. ATTENTION!!: Pass the tie through one (NOT two), of the available fixing holes.

The product contains bracket for wall mounting and spacers for ceiling mounting.

Step 3: Dismantle the luminaire by sliding the mounting part as shown in picture. Fasten the mounting

part (with screws from within) to either wall bracket(supplied), ceiling (with or without supplied

spacers), pendulum, wire or flag bracket.

Step 6: In case you use a module connect it on the PCB.

Step 5: Connect the battery cable to its respective connector on the PCB.

Step 2: Install the retaining clip to hold the pictograms.

click click

Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com

1 2 3 4

Switch 4 = ON

Maintained operation

(default position)

1 2 3 4

Switch 4 = OFF

Non-maintained

operation

1 2 3 4

(default position)

3h 8h

Step 7: The control of maintained or non maintained operation of the luminary is achieved through Switch

4 of DS1. For maintained operation, switch number 4 must be in ON position. For non-maintained

operation, switch number 4 must be in OFF position.

Step 8: Slide the two aluminium parts carefully together.

Step 9: Fasten the two screws (included) as shown in the picture.

Step 10: Fasten the two screws (included) as shown in the picture.

The user can select one of the 3 available minimum autonomy durations: 1 hour, 3 hours and 8 hours. The

selection must be done while the luminaire is disconnected from AC and battery supplies. The selection is

achieved through Switches 2 & 3 of DS1. Switch 1 is not used.

Two additional labels are included in the package, one for 3 hour duration (180) and one for 8 hour duration

(480). Depending on the selected duration, the installer must cover the default 1 hour (60) printing with

one that has the required duration.

Note: In case of mains power disconnection for a period of more than two months, the battery must be

disconnected.

Note: If the supply cable of the luminaire is damaged, it shall exclusively be replaced by a competent person

in order to avoid hazard.

Note: In case of battery replacement, this must be replaced with parts of the same type and characteristics.

The replacement must be performed by the manufacturer or a competent person.

To avoid that luminaires perform their battery test at

the same day, connect the battery packs with more

than 1,5 minutes inbetween.

Important notice when installing luminaires within the

same area!!!

7 8 9

Indicator LEDs

LED Status explanation

Description

GREEN

YELLOW

RED

Normal

Charging (battery test not possible while charging

Mains off, battery not connected or charger fault

Battery fault

Battery test

Light source test

Light source fault

Battery fault and light source fault

Off On Flashing

At the end of their useful life the packaging, product

and batteries should be disposed of via a suitable

recycling centre. Do not dispose of with your normal

household waste. Do not burn.

Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com

Technical description

Part no.:

Battery (LiFePO ):

Battery Protection:

Min. - Max. Charge Current: 25 - 125mA

Overcharge protection / Deep discharge protection

5 to 40 C

Up to 95%

8hours

Produced in accordance with:

Ambient Temperature Range:

Maximum Power Consumption:

Operation Voltage:

Relative Humidity:

Charging Time:

Technical lifetime (light source):

Lumen output, normal:

> 100000 hours

155lm 180lm

ExiLED M ST LED 25m 10Y 138h ExiLED M ST LED 40m 10Y 138h

220-240V AC, 50-60 Hz

138126.10138087.10

6.4V / 0.6Ah

3.8W / 4.1VA 4.1W / 4.4VA

IP40

1h / 3h / 8h manually selected (default 1h)

Degress of cover protection:

Emergency Mode Duration:

EN 60598-1, EN 60598-2-22, EN 55015

EN 61547, EN 61000-3-2, EN 61000-3-3

Charge Voltage Range: 5.6 - 7.3V

Lumen output, emergency (1h/3h/8h): 200/90/40lm 210/90/40lm

Weight:

Expected Battery Lifetime:

Controlgear classification in accordance with IEC 62034: with automatic test function

900 gr 1400 gr

10 years

The dimming setting remains stored in the luminaire even when both mains and battery voltages are disconnected.

Manual tests can only be performed if both mains and battery are connected.

By pressing the test button briefly (less than 5 seconds) an emergency operation test is performed. The exit sign will be lit for

approximately 3 seconds, the red indicator LED will flash during this test sequence.

To restore the original settings, repeat the above procedure.

By pressing the test button for a time space between 5 and 10 seconds, a battery condition test is performed. This test will

last for the stated duration and can only be performed when the battery is fully charged (steady green indicator LED). The

exit sign will be lit and the yellow indicator LED will flash during this test sequence.

Dimming

Push the test button for a time space between 10 and 15 seconds to delete all indicated errors. Then the luminaire enters

regular operation mode.

Resetting errors

By pressing the test button continuously for 15 seconds, when luminaire is connected to mains, the luminosity will be

reduced to 10% of its total luminance. In emergency mode the light output will remain unchanged.

Note: When using DALI or Wireless communication, the frequencies and schedules for tests will instead be determined by

the connected PC software.

Every 15 days the luminaire will perform an emergency operation test. This will light the exit sign for approximately 3

seconds. The red indicator LED will flash during this test sequence.

Selftest functions

Manual test functions

The ExiLED is a self-contained LED exit sign with selftest function.

It can be configured as maintained or non-maintained.

Every 6 months the luminaire will perform a battery condition test. The test will last for the stated duration. The exit sign will

be lit and the yellow indicator LED will flash during this test sequence.

Honeywell Life Safety AS, Postboks 236, 1372 Asker http://www.hls-nordic.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitsausrüstung Handbücher

Honeywell

Honeywell SPACEL 3000 Series Bedienungsanleitung

Honeywell

Honeywell MILLER MIGHTEVAC 1014390-A Bedienerhandbuch

Honeywell

Honeywell Miller TurboLite MFL Bedienerhandbuch

Honeywell

Honeywell NORTH OPENGO ABEKP15 Bedienungsanleitung

Honeywell

Honeywell MUTEX 2 Bedienungsanleitung

Honeywell

Honeywell Miller H-Design DuraFlex Bedienungsanleitung

Honeywell

Honeywell 15.112.816 Bedienerhandbuch

Honeywell

Honeywell Miller Turbolite Bedienerhandbuch

Honeywell

Honeywell Q-87586 Bedienerhandbuch

Honeywell

Honeywell Miller DuraHoist 3Pod Bedienerhandbuch

Honeywell

Honeywell satronic DMG 970 Bedienungsanleitung

Honeywell

Honeywell Miller EN 795 Bedienungsanleitung

Honeywell

Honeywell E3 Point E3SRMNO2 Bedienungsanleitung

Honeywell

Honeywell MILLER GlideLoc Body Control I Bedienerhandbuch

Honeywell

Honeywell EBI XLS MASS NOTIFICATION SYSTEM Bedienungsanleitung

Honeywell

Honeywell MILLER MIGHTYLITE+ MML-OGC1 Bedienungsanleitung

Honeywell

Honeywell Miller SCORPION 1016840 Series Bedienerhandbuch

Honeywell

Honeywell NORTH FP100 Bedienungsanleitung

Honeywell

Honeywell FF-SYA14 Series Bedienungsanleitung

Honeywell

Honeywell Miller Soll GlideLoc Bedienungs- und Wartungshandbuch

Honeywell

Honeywell MILLER Soll-MultiRail 17792 Technisches Datenblatt

Honeywell

Honeywell MILLER TurboLite EXTREME MFLEC-3/6FT Bedienerhandbuch

Honeywell

Honeywell SALISBURY ARC FLASH PROTECTIVE GARMENTS Bedienungsanleitung

Honeywell

Honeywell GENT S4-348 Series Gebrauchsanweisung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung

GRIDMESH ANCHOR

GRIDMESH ANCHOR GA01 Bedienungsanleitung