Honeywell Miller Soll GlideLoc Bedienungs- und Wartungshandbuch

www.honeywellsafety.com

Söll parallel switch

Söll GlideLoc® climbing protection system

EN 353-1:2014+A1:2017

in conjunction with Y-spar and twin ladder aluminum

Order no.

Mast diameter 200 - 350mm 16612

Mast diameter 351 - 500mm 18697

Mast diameter 501 - 700mm 18698

Mast diameter 701 - 1000mm 18699

in conjunction with Y-spar steel

Order no.

Mast diameter 200 - 350mm 16352

Mast diameter 351 - 500mm 18700

Mast diameter 501 - 700mm 18701

Mast diameter 701 - 1000mm 18702

clockwise (see Fig. B 17 for counterclockwise)

Installation, maintenance

& operating instructions

2www.honeywellsafety.com

Inhalt

A General 3

B Installation 5

C Review and acceptance 18

D Screw connections, screw locks 18

E Using the parallel switch 19

F Maintenance 21

G Checklist for acceptance 22

www.honeywellsafety.com

A General

A1. Anyone working with or on the Söll GlideLoc climbing protection system according to EN 353-

1 must be informed about the content of this manual before using the system. Acting contrary

to these instructions endangers human life.

A2. The operator of the fall protection system must ensure that these instructions are kept safe,

dry and accessible to the user at all times.

A3. These instructions must be provided by the operator of the system on request to the manufac-

turer of the fall arrest system (Honeywell Fall Protection Deutschland GmbH & Co. KG or one

of its authorized dealers).

A4. For the use of this Söll GlideLoc climbing protection system, the instructions for use of the

corresponding Söll fall arrester must be observed.

A5. For installation and use of Söll GlideLoc accessory parts on these fall arrest systems, the cor-

responding separate instructions must be observed.

A6. When using further personal protective equipment, the corresponding separate instructions

must be observed.

A7. The accident prevention regulations VBG 1 and VBG 74 as well as the „Guidelines for safety

and rescue harnesses“ ZH 1/709 and ZH 1/710 must be observed.

For installation the UVV VBG 37 as well as the reference book ZH 1/61 must be observed.

A8. Söll GlideLoc climbing protection devices may only be assembled and operated using original

Söll components/elements. The combination with components/elements of other manufactur-

ers can impair the safety of the Söll GlideLoc climbing protection systems. Product liability in

such cases is rejected by Honeywell Fall Protection Deutschland GmbH & Co. KG, as well

as by its authorized dealers. In addition, there is no approval in such cases, as Söll climbing

protection devices are tested and approved as a system. The full liability is thus transferred to

the operator.

A9. Thecontrollist(sectionG)mustbelledoutcompletelyandcorrectlybythesitemanagerof

theinstallationrmwithanindeliblepen.

A10. Before and during each use of the assembled fall protection system, a visual inspection of the

functionality of the system must be carried out.

4www.honeywellsafety.com

A11. Important: Climbing locks

For new assemblies, only the following types of climbing locks may be used in accordance

with the requirements of EN353-1: 2014 + A1: 2017:

These climbing locks must be used if the following refers to or depicts “upper climbing

lock” or “lower climbing lock”. A distinction in type between “upper” and “lower” is no longer

required.

When doing so, follow the assembly instructions for the respective climbing lock and in

particular the assembly position (arrow upwards).

Climbing locks with locking

bolts for steel/stainless steel

ladders

Climbing locks with locking

bolts for aluminum ladders

Mount from behind

(standard)

Lateral

mount

Mount from behind

(standard)

Lateral mount on the

spar mount bracket

www.honeywellsafety.com

B Installation

B1. The assembly kit consists of:

1 parallel switch (reversing ring with integrated carriage)

1 stop each on left and right

1 end stop each left and right

4 climbing locks

1 lock each on the right top and bottom

1 lock each on left top and bottom

B2. Functional items for easy installation:

1 - ring spanner SW 19 mm

2 - fork wrench, SW 10

1- hand drill

1- Drill 6.5mm

1- Handsaw

 1-roundle8mm

 1-atle,30mm

2- fall arresters

2 - safety harnesses EN 361

1 - roller boom (for a max. load of 20 kg), order no. 17563, for raising and lowering ladder

parts.

1-Rope for roller boom, max. 12mm diameter, length as needed 1- Tool bag

2-Handheld Radios

1 - pulley

At least 1 separate safety rope according to EN 354/355 with fall absorber to additionally

secure against falling during installation.

B3. Personnel required for installation: At least two persons

B4. Handle components gently, do not throw.

B5. Before installation, clean parts of dirt, especially at the connecting surfaces. Parts should

not come into contact with cement, mortar or similar substances. Mortar residues are to be

removed immediately. Especially the running surface for the fall arrester on the inside and

outside of the guide rail must be clean.

B6. Do not use damaged parts and do not repair them. They have to be replaced by brand

new parts.

B7. Minimum dimensioning for the mounting of climbing protection ladders:

The minimum dimension of the screws is M12. The order of the mounting bracket must be

designed for the used screw dimensioning.

Reference is made to the exclusive use of dowels approved by the building authorities.

6www.honeywellsafety.com

B8. Attention:

 Installationcanbeconducteddirectlyfromtheladderwithoutsca󰀨olding.Forthispurpose,

the installer shall use safety harness and fall arrester. In order to be protected against fal-

ling during a possible retraction of the fall arrester, the installer must always secure himself

with a safety rope according to EN 354/355 as shown in Fig. 1.

 Onlyplacethekarabinerhookofthesafetyropearoundtheguiderailwithapositivet

underneaththelastbracketrmlyconnectedtothestructureandtheladder.Neversecure

on the side rail of the ladder!

Fig. 1a, b, c, d

Correct

Incorrect Incorrect

Incorrect

www.honeywellsafety.com

B9. Attention:

 Theclimbinglocksandthemountingbracketsmustrstbemounteddirectlyaboveand

below the parallel switch installation location before the recess for the parallel switch is

sawn into the existing ladder.

If this is not possible, the installer must additionally attach himself to the mast with a

holding rope according to Fig. 2 in order to prevent any bending back of the ladder after

sawing and thus secure against falling.

Fig.2

Attention:

The function of the fall arrester is only guaranteed within the guide rail area secured by

climbing locks and when used as intended.

The insertion or removal of the fall arrester from the guide rail as well as the guiding over

the climbing lock with the arrester must be carried out in a secured position (for examp-

le,xedoor,securedplatform,securedhookingladderorsafetyropeaccordingto

EN 354/355).

Securing rope

8www.honeywellsafety.com

B10. Mountingbrackets(2.3)mustrstbeplaceddirectlyaboveandbelowtheinstallation

location of the parallel switch.

Attention:

If this is not possible, mount the mounting bracket (2.3) immediately after sawing out the

recess (see also point B 9. - Attention).

Furthermore, the „lower“ (2.1)* and „upper“ (2.2)* climbing locks must be mounted.

Important:

Above the parallel switch, the „lower“ (2.1)* climbing lock must be screwed from behind

through the square perforation of the central rail (2.0) so that the „upper“ (2.1)* climbing

lockislocatedimmediatelyabovetherstsparmountingbracketovertheparallelswitch

and the locking bolt is located on the right side of the central rail.

Belowtheparallelpoint,insertthe„upper“climbinglock(2.2)*intotherstsquareperfora-

tion below the last spar mounting bracket, so that the locking bolt is also on the right side

of the central rail.

Fig. 3

*Please observe the deviating instructions for using and installing the new climbing locks (A11).

www.honeywellsafety.com

B11. Saw out the central rails (2.0) of the Y-spars (in the case of twin ladders also the side rails)

between 2 rungs for the installation of the parallel switch. For this purpose, the cutting

lines 30mm and 217mm from the lower rung are marked and sawn out of the ladder

section applying straight cuts.

Note:

Ensure that the recesses in the Y-spar of the two climbing paths are at the same height to

ensure correct installation.

Attention:

The climbing locks „lower“ (2.1)* and „upper“ (2.2)* may only be guided over after the

parallel switch has been mounted and the carriage has been locked in the correspond-

ing end position, or if a fall arrest system is in place (e.g. with safety rope according to

EN 354/355).

Fig. 4

* Please observe the deviating instructions for using and installing the new climbing locks (A11).

10 www.honeywellsafety.com

Self-locking nut

M6 – DIN 985

Hex bolt

M6x20 – DIN 933

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitsausrüstung Handbücher

Honeywell

Honeywell HCL-1PH Bedienungsanleitung

Honeywell

Honeywell MILLER GlideLoc Body Control I Bedienerhandbuch

Honeywell

Honeywell Miller Falcon Edge Bedienerhandbuch

Honeywell

Honeywell Miller MLAS Bedienungsanleitung

Honeywell

Honeywell Miller Vi-Go Bedienungsanleitung

Honeywell

Honeywell satronic DMG 970 Bedienungsanleitung

Honeywell

Honeywell SALISBURY ARC FLASH PROTECTIVE GARMENTS Bedienungsanleitung

Honeywell

Honeywell Miller H-Design DuraFlex Bedienungsanleitung

Honeywell

Honeywell MILLER H500 Bedienungsanleitung

Honeywell

Honeywell MaxLED 26m Bedienungsanleitung

Honeywell

Honeywell ESSIAN 2 Bedienungsanleitung

Honeywell

Honeywell Miller AirCore Series Bedienungsanleitung

Honeywell

Honeywell FF-SYA14 Series Bedienungsanleitung

Honeywell

Honeywell MILLER TurboLite EXTREME MFLEC-3/6FT Bedienerhandbuch

Honeywell

Honeywell Miller EN 795 Bedienungsanleitung

Honeywell

Honeywell COMBISAFE SkyReach 8100 Bedienungsanleitung

Honeywell

Honeywell FF-SB14 Series Handbuch

Honeywell

Honeywell FF-SYA234 Series Bedienungsanleitung

Honeywell

Honeywell MUTEX 2 Bedienungsanleitung

Honeywell

Honeywell ExiLED Bedienungsanleitung

Honeywell

Honeywell MILLER MIGHTYLITE+ MML-OGC1 Bedienungsanleitung

Honeywell

Honeywell UniLED Bedienungsanleitung

Honeywell

Honeywell A164221 Bedienungsanleitung

Honeywell

Honeywell MFL/6FT Bedienerhandbuch

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung

GRIDMESH ANCHOR

GRIDMESH ANCHOR GA01 Bedienungsanleitung