Honeywell MaxLED 26m Bedienungsanleitung

MaxLED

Dimensional Drawings:

330mm

230mm

336mm

460mm

427mm

700mm

198mm

52mm

304mm

52mm

395mm

52mm

MaxLED 26m MaxLED 47m MaxLED 65m

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

Installation:

Step 1: To dismantle the luminaire, push the lock/unlock button, slide the luminaire to the left

and pull it down.

Step 2: To gain access to the module address SET-10, lift the inner plastic cover (on top of the

luminaire).

Step 4: To insert pictograms, first unscrew the two screws holding the side profile and remove

the profile.

Step 5: For double sided pictogram, insert the appropriate pictograms to both sides and refit

the profile. For single sided pictogram, there is one blind pictogram in the package.

Step 3: Set the module address. For more information about module settings see the next

page.

1 2 3

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

The product contains bracket for wall mounting and spacers for ceiling mounting.

Step 3: Tighten the cable tie around the cables.

Step 4: Slide the luminaire into the socket. The lock/unlock button appears

indicating that the luminaire is securely installed.

Step 2: Pass the mains cables through the cable gland. Always use in any

case round mains cable, with a diameter of 5-10mm (H05RN-F

type 2x1mm² or any other type, at least equal to it's mechanical and

electrical properties). ATTENTION!! The cable must not be

deformed in any way (This requirement is important to ensure the

IP rating). Connect the mains to terminal blocks: L for live wire, N for

neutral and PE for ground.

Step 1: Fasten the mounting part (with screws from within) to either wall bracket (supplied), ceiling (with or without

supplied spacers). If mounted close to a wall make sure, that the

unlock button is facing outwards.

Mouting Methods:

PRESS HERE

TO UNLOCK

PRESS HERE

TO UNLOCK

Power

cable Power

cable

Metal Wall Bracket

Spacers

Wall Mounting

Ceiling Mounting

At the end of their useful life the packaging and product should

be disposed of via a suitable recycling centre. Do not dispose of

with your normal household waste. Do not burn.

Technical description

Part no.:

-10 to 60 C

Up to 95%

Produced in accordance with:

Ambient Temperature Range:

Maximum Power Consumption:

Operation Voltage:

Relative Humidity:

Technical lifetime (light source):

Lumen output

> 100000 hours

280lm 550lm 850lm

MaxLED 26m MaxLED 65mMaxLED 47m

3.1W / 3.8VA 5.4W / 5.9VA 7.7W / 8.2VA

220-240V AC/DC, 50-60 Hz

290253.S10 290255.S10290254.S10

IP40

Degress of cover protection:

EN 60598-1, EN 60598-2-22, EN 55015

EN 61547, EN 61000-3-2, EN 61000-3-3

Weight: 800 gr 1190 gr 1765 gr

The light source contained in this luminary shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

MODULE FOR SINGLE LAMP SELECTION AND MONITORING

Switching of one selected light in the electric circuit

SET010 select

DIP-switch 1

ON for non-maintained mode

OFF for maintained mode (Default)

DIP-switch 2

OFF for lighting address 1-16 (Default)

ON for lighting address 17-32

Indicator LED

Rotary coding switch

for setting the exact lamp adress DIP-switch 3 (OFF)

Attention!

Connect L and N correctly!

Exchanging L and N causes malfunction.

Function

Setting the lighting address is carried out by a rotary coding switch that is easily accessible from the

outside.

By means of a suitable control, it is possible with the aid of the SET010 select to determine whether the

lamp connected to it is ready for use or faulty.

In the mixed operation circuit, the connected lamp can also be additionally set in non-maintained mode

or maintained mode (DIP Switch 1).

The address range 17 to 32 can be selected by setting DIP switch 2 to ON.

The module is already prepared for administering a total of 32 lighting addresses.

Settings

Lighting addresses 1 to 16 can be slected when DIP switch 2 is set at OFF.

(DIP switch 2 = ON and rotary coding switch = 1 is equivalent to lighting address 17 etc.)

Technical description

Cross section:

Temperature:

Dimensions (L x W x H in mm) 78 x 30 x 20

Max: 1.5mm

-10°C up to +60°C, T =+75°C

cmax

SET010 select

Prewired

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitsausrüstung Handbücher

Honeywell

Honeywell Q-87586 Bedienerhandbuch

Honeywell

Honeywell A164221 Bedienungsanleitung

Honeywell

Honeywell Miller EN 795 Bedienungsanleitung

Honeywell

Honeywell Miller H-Design DuraFlex Bedienungsanleitung

Honeywell

Honeywell MILLER MIGHTYLITE+ MML-OGC1 Bedienungsanleitung

Honeywell

Honeywell Miller H-Design DuraFlex Bedienungsanleitung

Honeywell

Honeywell Miller Soll VR500 Bedienungsanleitung

Honeywell

Honeywell SALISBURY ARC FLASH PROTECTIVE GARMENTS Bedienungsanleitung

Honeywell

Honeywell Miller SCORPION 1016840 Series Bedienerhandbuch

Honeywell

Honeywell Miller Vi-Go Bedienungsanleitung

Honeywell

Honeywell Miller AirCore Series Bedienungsanleitung

Honeywell

Honeywell GENT S4-348 Series Gebrauchsanweisung

Honeywell

Honeywell BA300 Series Bedienungsanleitung

Honeywell

Honeywell MUTEX 2 Bedienungsanleitung

Honeywell

Honeywell MILLER MIGHTEVAC 1014390-A Bedienerhandbuch

Honeywell

Honeywell VA201T Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell SPACEL 3500 Bedienungsanleitung

Honeywell

Honeywell E3 Point E3SRMNO2 Bedienungsanleitung

Honeywell

Honeywell COMBISAFE SkyReach 8100 Bedienungsanleitung

Honeywell

Honeywell RG500 Bedienungsanleitung

Honeywell

Honeywell Miller EN 795 Bedienungsanleitung

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

Honeywell

Honeywell Miller SafEscape ELITE SEHWLB FT Series Bedienungsanleitung

Honeywell

Honeywell Miller VC300 Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung

GRIDMESH ANCHOR

GRIDMESH ANCHOR GA01 Bedienungsanleitung