Hoover PRO STAIR Bedienungsanleitung

USER

INSTRUCTIONS

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 1

-2-

IMPORTANT SAFETY REMINDERS

User’s manual- This cleaner should only be

used for its intended purpose as described in

these instructions. Ensure that these are fully

understood before operating this appliance.

Only use attachments recommended or

supplied by Hoover.

When using cleaning tools ensure that the

cleaner is kept in the upright (parked)

position. This will avoid possible damage to

the carpet or floor covering.When cleaning

stairs DO NOT position the cleaner above

you.

STATIC ELECTRICITY. Some carpets can

cause a small build up of static electricity.

Any static discharge is not hazardous to

health.

DO NOT use your cleaner out of doors or

on any wet surface or for wet pick up.

Keep hands, feet, loose clothing and hair

away from rotating brushes.

DO NOT

pick up hard or sharp objects,

matches, cigarette ends or other similar

items.

DO NOT pick up flammable liquids such as

cleaning fluids, petrol etc. or their vapours.

Aerosol sprays may be flammable.

DO NOT

spray near cleaner.

SUPPLY CORD. DO NOT run over the

supply cord when using your cleaner or

remove the plug by pulling on the supply

cord.

FAULTS. DO NOT continue to use your

cleaner if it appears to be faulty. If the supply

cord is damaged stop using the cleaner

IMMEDIATELY .The supply cord must be

replaced by an authorised Hoover service

engineer to avoid a safety hazard.

AFTER USE. Switch the cleaner off and

remove the plug from the electricity supply.

Always switch off and remove the plug

before cleaning the appliance or attempting

any maintenance task.

HOOVER SERVICE.To ensure the continued

safe and efficient operation of this appliance

we recommend that any servicing or repairs

are only carried out by an authorised

Hoover service engineer.

HOOVER SERVICE 08705 400 600

HOOVER SPARES 01204 556 111

Genuine Hoover Spares and Consumables

Always replace parts with Genuine Hoover spares and consumables.

Safety with Children, Elderly or the Infirm:

Do not let children play with the appliance

or its controls. Please supervise the use of

the appliance by older children, the elderly

and the infirm.

Congratulations on the purchase of your

new Hoover Pro Stair.

This highly advanced machine makes

cleaning easier and more ecient.

You’ll nd it kinder to your carpets - and

to you!

Please take the time to read this manual

carefully.

You’ll be ready to make the most of the

special features only the new Hoover

Pro Stair can oer!

WARNING!

ELECTRICITY CAN BE

EXTREMELY DANGEROUS

This appliance is double insulated and must not be

earthed.

The plug is fitted with a 13 amp fuse.

IMPORTANT:The wires in the mains lead

are coloured in accordance with the

following code:

Blue - NEUTRAL

Brown - LIVE

PRO STAIR

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 2

PRO STAIR

-3-

GETTING TO KNOW YOUR CLEANER*

Effortless

cleaning

with your

new Hoover

PRO STAIR

When rst unpacking

your cleaner please

check all items are

included.

If any parts are missing,

contact your retailer or

call the Hoover helpline

on 08705 400 600

Handle

Cleaner body

On/Off switch

Door release

Door

Carpet Height Selector

Handle lock release

Supply cord

Dusting brush

Grooming nozzle

Hose supports

Carrying handle

Hose retainer

Pro Stair

Telescopic Tube

Long Crevice Tool

Note: The Long Crevice Tool is located inside the Pro Stair Telescopic Tube,

they must be seperated before use of either item.

Hose hook

Cord storage

swivel hook

Pro Stair Brush

Flexible hose

Hose supports

Exhaust filter cover

behind Pro Stair Lock

Pro Stair Lock

* Features vary according to model

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 3

-4-

PREPARING TO USE YOUR CLEANER

1Insert handle into body of cleaner. Slide into

position.

Ensure handle is flush with body of cleaner.

Tighten large screw (pre-fitted to handle

upper hole). Insert small screw into handle

lower hole and tighten.

2Locate hose end, turn clockwise to lock.

3Locate hose retainer on lower hose support.

4Position hose over hose supports.

5Push handgrip firmly into socket.

Clip tools to back of cleaner.

Check that dust container is fitted

POWER SWITCH SETTING

Switching on and o

Push bottom of the switch to switch on.

Push top of switch to switch off.

CARPET HEIGHT SELECTOR

The carpet height selector raises or lowers the height of

the nozzle.The nozzle height will not change until the

handle is released.Try various settings until you get the

best results for each of your carpets.

IMPORTANT:When cleaning hard oors

such as vinyl or linoleum, move the

“Carpet Height selector” to the

Hard oor position. Failure to do so may

cause damage to the oor surface.

Ensure that the cleaner

is in an upright (parked)

position.

Slide selector to position

best suited to depth of

carpet pile.

Using this cleaner for carpets with pile greater than

30mm is not recommended.

HANDLE LOCK RELEASE

Unlock the handle by pressing

down on pedal with foot. For

cleaning under low

furniture and some

maintenance tasks

simply press

pedal again and

lower handle

to floor.

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 4

-5-

CLEANING TOOLS*

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 5

IMPORTANT:When using cleaning tools, the cleaner must be kept in the

upright (parked) position, particularly when cleaning stairs.The carpet

height selector should also be set to tool mode:

CLEANING THE STAIRS

It is dangerous for the cleaner to be above you at the

top of the stairs.

ALWAYS work with the cleaner below you. Ensure it is

positioned up against the bottom step.

DO NOT attach hose retainer when cleaning the stairs.

PRO STAIR LOCK FEATURE*

The PRO STAIR LOCK has been designed to improve cleaner stability when you pull on

the hose while stair cleaning. It can be adjusted to suit any staircase.

* Features vary according to model

Location.

The PRO STAIR LOCK, stability

device, is located at the back of the

cleaner.

Pull the bottom of the device to

release it from its storage

position.

Operation.

Lift the device upwards to the

position shown in the diagram.

Simultaneously squeeze the finger

tabs and extend the device.

Use.

Place the cleaner against the stairs

and the PRO STAIR LOCK in the

position shown. Use the stair

cleaning hose and accessories as

usual.

To return the cleaner to carpet

mode, repeat the above process in

reverse.

The Pro Stair Brush is the ideal tool for stair

cleaning incorporating a rotating brush that

deep cleans and grooms the carpet.

DO NOT TOUCH THE ROTATING BRUSH.

The Pro Stair Brush also converts to a Crevice

tool to clean the corners between treads and

risers.

Always attach the hose retainer to the hose

hook when using the cleaning tools.

Unhook after use

Pro Stair Telescopic Tube

Fitted on the flexible hose and with accessories

at its end, its ideal for stair cleaning.

It extends to minimise stretching and bending.

All accessories can fit on the end of the flexible

tube. Combine accessories depending on use.

To use your Pro Stair Brush as

a crevice tool rotate the tool to

the ‘Open’ position as shown.

When using the Pro

Stair Brush keep the base

of the nozzle flat to the

carpet.

When cleaning treads &

risers use the crevice

tool in the ‘OPEN’

position.

-6-

CHANGING BELT OR BRUSHES

IMPORTANT: Switch cleaner o and

remove plug from electricity supply

before checking the brushes or removing

hood.

If your cleaner is not picking up efficiently, the

belt or brushes (or both) may need replacing,

but first make sure you have:

•Emptied the dust container

•Cleaned filters

•Checked for blockages

Remove hood

•Prise off the carpet height selector

•Remove hood screws A and B

Lift off hood

Remove brush assembly

•Inspect belt for signs of wear.

•To remove, pull brush cleaner assembly

upwards out of cleaner housing. Remove belt

from motor spindle then from brush assembly.

Replace belt

•Loop the new belt around the motor spindle

then around the brush channel.

Ret brush assembly

•Hold the brush assembly and

stretch the belt until brush

mountings slot down into the

cleaner housing.

Rotate the brush to ensure free

movement of the belt.

Ret hood

•Refit hood, ensuring the lugs

along the front of hood are

located in the slots along the

front edge of baseplate.

•Secure hood, using screws

A and B.

Ret carpet height selector

•Ensure the raised face (T) is

towards the front of the

cleaner.

CLEARING A BLOCKAGE*

IMPORTANT: Switch the cleaner o

and remove the plug from the

electricity supply before dismantling

cleaner.

This cleaner is unlikely to become blocked, except by

overfilling of the dust container or accidentally

picking up large solid objects. Clearing a blockage is

simple. If cleaning tools were in use,

check cleaning tool and

extension tube first. Next

check hose handgrip; to

remove grip ribbed ring as

shown, turn in direction of

arrow and ease apart.

To check the hose, stretch it

to full length and switch on

the cleaner; the suction will

dislodge most obstructions. If

this is unsuccessful, switch off

and unplug the cleaner.

Remove the hose by turning

it anti-clockwise as shown.

Detach cassette and remove

blockage.

For blockages in cleaner base:

1.Turn the cleaner over

and check that the

brushes are free to

rotate.

2. Check for a blockage

in hose socket. Use a

piece of wire or a blunt

flexible rod to remove

any obstructions.

* Features vary according to model

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 6

-8-

User checklist

If your cleaner is not working properly run through the following checklist.

1. Is there a working electricity supply to the cleaner?

check with another electrical product.

2. Is the dust container full or choked with ne dust?

To empty the dust container see the instructions on page 8.

3. Is the hose blocked?

To clear a blockage, see the instructions on page 6.

4. Is there a blockage in the cleaner base?

To clear a blockage, see the instructions on page 6.

5. Are the lters blocked?

To clear the lters, see the instructions on page 8.

6. Is the nozzle height set correctly?

To set the carpet height selector, see the instructions on page 4.

7. Are the brushes rotating correctly?

To check the brushes, see the instructions on page 6.

8. Has the cleaner overheated? If so, it will take about 30 minutes to reset itself.

If there is any doubt call the Hoover Service Oce for advice. They may be

able to assist you over the telephone.

A service charge will be made if the cleaner is examined and found to be in

working order, has not been assembled in accordance with these instructions or

has been used incorrectly.

WARNING!

A thermal cut out switches o the cleaner to prevent

overheating if it is used when full or there is a blockage or

dirty lters. If this should happen switch o, unplug and

correct the fault.

It will take about 30 minutes for the cut out to

automatically reset.

IMPORTANT: Do not run cleaner over the supply

cord as this could damage the supply cord insulation.

Hoover Limited

Pentrebach

Merthyr Tydl

Mid Glamorgan

CF48 4TU

Registered Trade Mark

Part Number: 0565 5261

EMPTYING AND CLEANING THE DUST

CASSETTE AND FILTERS*

Press down on door release pad and remove door. Pull out the dust cassette. Empty

the cassette of dirt and debris. Clean the Red cyclonic screen after each empty.

Washing cassette lter and foam:

Washing pre-motor and exhaust lter:

After emptying the cassette 5

times, wash the Blue top filter and

and foam under hand warm water.

Remove excess water by shaking

and leave to dry for 24 hours.

Do not use a brush as this will

damage the filter.

The pre-motor lter should be washed every three

months.Wash under hand warm water. Remove excess water

by shaking and leave to dry for 24 hours.When completely

dry, refit the filter.

Carbon lter

Normally maintenance free, this component should not be washed. If a replacement is

required please contact our spares department.

The exhaust lter should be washed every 3 months.

press down on the latch to remove the exhaust cover

and filter.

Wash under hand warm water.

Remove excess water by shaking and leave to dry for

24 hours.

* Features vary according to model

Hoover_Stabiliser_FINAL_Vs2c_01_03_06.qxp 01/03/2006 10:28 Page 8

Andere Handbücher für PRO STAIR

Inhaltsverzeichnis

Andere Hoover Staubsauger Handbücher

Hoover

Hoover U5184 Bedienungsanleitung

Hoover

Hoover HH87-LX2-ID Bedienungsanleitung

Hoover

Hoover U5753900 Bedienungsanleitung

Hoover

Hoover FH50035 - SteamVac Carpet Cleaner Bedienungsanleitung

Hoover

Hoover Jive Bedienungsanleitung

Hoover

Hoover Stick Cleaner S2535 Bedienungsanleitung

Hoover

Hoover HGO320H Bedienungsanleitung

Hoover

Hoover Savvy U8185 Bedienungsanleitung

Hoover

Hoover WindTunnel U5720-960 Bedienungsanleitung

Hoover

Hoover S2IN1600 Bedienungsanleitung

Hoover

Hoover F7410 Bedienungsanleitung

Hoover

Hoover SSN1700 Steamjet Bedienungsanleitung

Hoover

Hoover POWERDASH PET Bedienungsanleitung

Hoover

Hoover Power Nozzle Bedienungsanleitung

Hoover

Hoover Sensory Bedienungsanleitung

Hoover

Hoover U3721 Bedienungsanleitung

Hoover

Hoover smart R1 Bedienungsanleitung

Hoover

Hoover HHWD14 Installationsanleitung

Hoover

Hoover 3000 PERFORMER Bedienungsanleitung

Hoover

Hoover KS42JCAR 011 Bedienungsanleitung

Hoover

Hoover MPWR 40V CH93619 Bedienungsanleitung

Hoover

Hoover Sprint Bedienungsanleitung

Hoover

Hoover Freespace TFS-8205 Bedienungsanleitung

Hoover

Hoover ATHEN Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch