HP 04H8095 Bedienungsanleitung

Auto LANstreamer PCI Adapter

04H8095

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.

• Driver Name: IBMMPC.DOS Size: 59KB Date: 5/22/95

• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Interrupt 9 (2)

• I/O Address FCC0-h

Procedure

1With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR

adapter card into a PCI slot.

2Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer

PCI Diagnostic Disk) and power on the machine.

3After the machine boots, verify that the adapter finished testing and that

the adapter is “OK.”

4Click on “F3” to exit, and then press “CTRL+ALT+DEL.”

5Boot the machine to a DOS prompt, and Netware client for DOS and MS-

Windows disk 1.

6Execute INSTALL.EXE and set lines 1-5 as listed below;

• C:\NWCLIENT

•YES

C:\WINDOWS

•NO

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

• IBM Auto LANStreamer PCI Adapter (use the driver on disk 3 of 5, Net-

ware DOS requester Installation disk)

7Highlight option 6 to continue with installation.

8When prompted, insert the corresponding disks to complete file transfer

and driver installation.

9When the install utility is finished, press <CRTL><ALT><DEL> to restart

the machine.

10 After windows loads, open the “NETWORK” folder, and double-click the

“NETWORK SETUP” icon.

11 Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0

and above)” is selected under “Install Windows support for the following

network only:”

12 Click on “OK” twice and the installation is complete.

1 Connecting to Netware 3.12 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95 SR2 installed.

• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.

• Driver Name: Windows 95 Default

• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

Device Configuration

• Interrupt 9 (2)

• I/O Address FCC0-h

Procedure

1With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR

adapter card into a PCI slot.

2Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer

PCI Diagnostic Disk) and power on the machine.

3After the machine boots, verify that the adapter finished testing and that

the adapter is “OK.”

4Click on “F3” to exit, and then press “CTRL+ALT+DEL.”

5Upon booting, Windows 95 will automatically recognize the adapter. Click

on “Next.”

6When prompted, click on “Other Locations.”

7Insert drivers disk 4 of 6 (Auto LANStreamer PCI NDIS 3.0 Driver

Diskette), set the path to “A:\” and click “OK.” (If you have an HP

preloaded HDD, set the path to “C:\LANDRV\LNSTRM\DISK4\”)

8Verify that “IBM Auto LANStreamer PCI Adapter (NDIS3)” is listed and

click on “Finish.”

9When prompted to insert disk labeled “IBM Streamer Family Adapter

Option Diskette”, click on “OK.”

10 Insert disk 2 of 6 (Auto LANStreamer PCI Driver Diskette), set the path

to “A:\” and click “OK.” (If you have an HP preloaded HDD, set the path

to “C:\LANDRV\LNSTRM\DISK2\”)

11 At the “Copying Files” window, click on “OK.”

1 Connecting to Netware 3.12 Server

Windows 95 SR2

12 Click “OK” to provide your Computer and Workgroup names.

13 Enter your Computer Name, Workgroup Name, Computer Description,

and click on “Close.”

14 Accept the default properties, and click on “OK.”

15 When prompted to insert the Windows 95 CD-ROM, click on “OK.”

16 Set the path to your Windows 95 files and click on “OK.” (If you have an

HP pre-loaded HDD, set the path statement

C:\MASTERS\WIN95\SYSTEM\CABS\”).

17 When prompted to insert the disk labeled “IBM Streamer Family Adapter

Option Diskette”, click on “OK.”

18 Insert disk 4 of 6 (Auto LANStreamer PCI Driver Diskette), set the path

to “A:\Win95\” and click “OK.” (If you have an HP preloaded HDD, set the

path to “C:\LANDRV\LNSTRM\DISK4\WIN95\”)

19 Click on “Yes” to restart your computer and finish the installation.

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

2 Connecting to a Netware 4.11 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.

• Driver Name: IBMMPC.DOS Size: 59KB Date: 5/22/95

• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Interrupt 9 (2)

• I/O Address FCC0-h

Procedure

1With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR

adapter card into a PCI slot.

2Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer

PCI Diagnostic Disk) and power on the machine.

3After the machine boots, verify that the adapter finished testing and that

the adapter is “OK.”

4Click on “F3” to exit, and then press “CTRL+ALT+DEL.”

5Boot the machine to a DOS prompt, and Netware client for DOS and MS-

Windows disk 1.

6Execute INSTALL.EXE and set lines 1-5 as listed below;

• C:\NWCLIENT

•YES

C:\WINDOWS

•NO

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

• IBM Auto LANStreamer PCI Adapter (use the driver on disk 3 of 5, Net-

ware DOS requester Installation disk)

7Highlight option 6 to continue with installation.

8When prompted, insert the corresponding disks to complete file transfer

and driver installation.

9When the install utility is finished, press <CRTL><ALT><DEL> to restart

the machine.

10 After windows loads, open the “NETWORK” folder, and double-click the

“NETWORK SETUP” icon.

11 Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0

and above)” is selected under “Install Windows support for the following

network only:”

12 Click on “OK” twice and the installation is complete.

2 Connecting to a Netware 4.11 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95 SR2 installed.

• IBM LANStreamer 16/4 PCI TR adapter and drivers diskettes ver 1.01.

• Driver Name: Windows 95 Default

• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

Device Configuration

• Interrupt 9 (2)

• I/O Address FCC0-h

Procedure

1With the HP Vectra turned off install the IBM LANStreamer 16/4 PCI TR

adapter card into a PCI slot.

2Insert the IBM LANStreamer TR drivers disk 1 of 6 (AUTO LANStreamer

PCI Diagnostic Disk) and power on the machine.

3After the machine boots, verify that the adapter finished testing and that

the adapter is “OK.”

4Click on “F3” to exit, and then press “CTRL+ALT+DEL.”

5Upon booting, Windows 95 will automatically recognize the adapter. Click

on “Next.”

6When prompted, click on “Other Locations.”

7Insert drivers disk 4 of 6 (Auto LANStreamer PCI NDIS 3.0 Driver

Diskette), set the path to “A:\” and click “OK.” (If you have an HP

preloaded HDD, set the path to “C:\LANDRV\LNSTRM\DISK4\”)

8Verify that “IBM Auto LANStreamer PCI Adapter (NDIS3)” is listed and

click on “Finish.”

9When prompted to insert disk labeled “IBM Streamer Family Adapter

Option Diskette”, click on “OK.”

10 Insert disk 2 of 6 (Auto LANStreamer PCI Driver Diskette), set the path

to “A:\” and click “OK.” (If you have an HP preloaded HDD, set the path

to “C:\LANDRV\LNSTRM\DISK2\”)

11 At the “Copying Files” window, click on “OK.”

2 Connecting to a Netware 4.11 Server

Windows 95 SR2

12 Click “OK” to provide your Computer and Workgroup names.

13 Enter your Computer Name, Workgroup Name, Computer Description,

and click on “Close.”

14 Accept the default properties, and click on “OK.”

15 When prompted to insert the Windows 95 CD-ROM, click on “OK.”

16 Set the path to your Windows 95 files and click on “OK.” (If you have an

HP pre-loaded HDD, set the path statement

C:\MASTERS\WIN95\SYSTEM\CABS\”).

17 When prompted to insert the disk labeled “IBM Streamer Family Adapter

Option Diskette”, click on “OK.”

18 Insert disk 4 of 6 (Auto LANStreamer PCI Driver Diskette), set the path

to “A:\Win95\” and click “OK.” (If you have an HP preloaded HDD, set the

path to “C:\LANDRV\LNSTRM\DISK4\Win95\”)

19 Click on “Yes” to restart your computer and finish the installation.

Andere HP PCI-Karte Handbücher

HP NC380T Gebrauchsanweisung

HP Vectra VL410 Bedienungsanleitung

HP A7173A Bedienungsanleitung

HP Vectra VEi 7 Bedienungsanleitung

HP Vectra VEC 7 Bedienungsanleitung

HP Model 748 - VME Workstation Bedienungsanleitung

HP Edgeline EL1000 Bedienungsanleitung

HP NC375T Bedienungsanleitung

HP NC1020 Gebrauchsanweisung

HP VL600 - Vectra - 128 MB RAM Bedienungsanleitung

HP AB465A Bedienungsanleitung

HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

HP Vectra VE6 8 Bedienungsanleitung

HP 435508-B21 Gebrauchsanweisung

HP PCIe 2-Port 10GbE Bedienungsanleitung

HP FC HBAs Installationsanleitung

HP 4X - DDR InfiniBand Mezzanine HCA Merkblatt

HP Compaq Pro 6305 Bedienungsanleitung

HP StorageWorks Q2300 Bedienungsanleitung

HP Vectra VL6 8 Bedienungsanleitung

HP Vectra VL6 7 Bedienungsanleitung

HP Vectra VEi 7 Bedienungsanleitung

HP Vectra VL6 6 Bedienungsanleitung

HP Thunderbolt 3 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung