HP Vectra VEC 7 Bedienungsanleitung

Etherlink III PCI Network Interface

Card (10BT)

3C590-TPO

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.1A.

DOS ODI - File Name: EL59X.DOS Size: 27KB Date: 10/04/96

• DOS and MS-Windows for Workgroups 3.11 media.

• Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Network Driver Optimization Normal

• Full Duplex Disabled

• Boot PROM Disabled

• Media Type 10BASE-T

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and allow it to boot to a DOS prompt.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C59XCFG.EXE.

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address FCCO (PCI) FCC0h (PCI) DC00h (PCI)

Interrupt Request

Level

10 (PCI) 9 (PCI) 10 (PCI)

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

6Remove the 3com cards driver diskette and insert Netware client for DOS

and MS-Windows disk 1.

If you are using a Vectra VL7 or VE7/VE8, follow the instructions below to

complete the installation. If you are using a VL8, go directly to step 7.

aExecute INSTALL.EXE.

bSpecify the settings as listed below:

• C:\NWCLIENT

•Yes

• C:\WINDOWS

•No

• 3Com Fast Etherlink/Etherlink III Bus Master

cUnder the heading "Select the driver for your network board", insert

the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\

CLIENT." (If you have an HP preloaded HDD, set path to "C:\Masters\

LanDrv\3C590\NETWARE\CLIENT\)

dPress "Enter" to continue the installation.

eWhen prompted, insert the corresponding disks to complete file trans-

fer and driver installation.

fWhen the install utility is finished, press <CRTL><ALT><DEL> to

restart the machine.

gAfter Windows loads, open the "NETWORK" folder, double-click the

"NETWORK SETUP" icon.

hSelect "Networks" and verify that "Novell Netware (Workstation Shell

4.0 and above)" is selected under "Install Windows support for the

following network only:"

iSelect "OK" twice, and the installation is complete.

7Execute INST_DOS.EXE and enter Yes to accept the agreement.

8Accept the default products by pressing Enter, and then press “F10” to

continue.

9Select 16-bit LAN Drivers and hit the Enter key.

10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

and hit enter.

11 Insert the 3COM Etherlink 3C590 Ethernet card and drivers disk, set the

path to “A:\NETWARE\CLIENT\” and press enter.

12 Select “3Com Fast Etherlink / Etherlink III Bus Master Family” and press

enter.

13 Accept the default settings, press “F10” to continue, and verify the

following entries for the “Installation Configuration Summary”:

❒YES

❒C:\NOVELL\CLIENT32

❒C:\WINDOWS

❒16-bit LAN drivers

❒3Com Fast Etherlink / Etherlink III Bus Master Family

14 Press “F10” to save and continue.

15 When prompted, insert the corresponding disks to complete file transfer

and driver installation.

16 When the install utility is finished, press <CRTL><ALT><DEL> to restart

the machine.

17 After windows loads, open the “NETWORK” folder, double-click the

“NETWORK SETUP” icon.

18 Select “Networks”, and verify that “Novell Netware (Workstation Shell 4.0

and above)” is listed under “Install Windows support for the following

network only:” and click on “OK.”

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95 SR2 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.1a.

• File Name: EL59X.VXD Size: 38KB Date: 1/27/97

Driver for Vectra VE7/VE8: Windows 95 Embedded

• Windows 95 SR2 media (If you have an HP preloaded HDD, the media is

located at C:\Masters\Win95\System\Cabs\)

• Novell Netrware 3.12 server that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

Device Configuration

• Network Driver Optimization Normal

• Full Duplex Disabled

• Boot PROM Disabled

• Media Type 10BASE-T

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C59XCFG.EXE.

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

6Remove the 3com cards driver diskette and restart the machine.

7Windows 95 SR2 should automatically recognize the 3COM 3C590

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address FCC0h (PCI) FCE0h (PCI) DC00h (PCI)

Interrupt Request

Level

10 (PCI) 9 (PCI) 10 (PCI)

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

ethernet card

8When prompted, click on “OK” to continue.

9Enter “Computer Name”, “Workgroup”, and “Computer Description” data

and then open the “Configuration” folder.

10 In the “Configuration” folder, click on “Add”, then click on “Protocol” and

click on “Add” once again.

11 Listed under “Manufacturers”, select “Microsoft”, then select “TCP/IP”

under “Network Protocols:” and click on “OK.”

12 In the “Network” window, click on “Close” to continue the installation.

13 After files copy, you will be asked to restart your computer. Click on

“Yes.”

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

2 Connecting to a Netware 4.11 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.1a.

DOS ODI -

Vectra VL8 Driver File Name: 3C59X.COM Size: 55KB Date:10/04/96

• Vectra VL7 and VE7/VE8 Driver File Name: EL59X.DOS Size:27KB

Date: 10/04/96

• DOS and MS-Windows for Workgroups 3.11 media.

• Novell Netware server 4.1 that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Network Driver Optimization Normal

• Full Duplex Disabled

• Boot PROM Disabled

• Media Type 10BASE-T

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and allow it to boot to a DOS prompt.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C59XCFG.EXE.

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address FCC0h (PCI) FCC0h (PCI) DC00h (PCI)

Interrupt Request

Level

10 (PCI) 9 (PCI) 10 (PCI)

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

6Remove the 3com cards driver diskette and insert Netware client for DOS

and MS-Windows disk 1.

If you are using a Vectra VL8, go directly to step 7.

If you are using a VL7 or VE7/VE8, follow the instructions below to

complete the installation.

aExecute INSTALL.EXE.

bSpecify the settings as listed below:

• C:\NWCLIENT

•Yes

• C:\WINDOWS

•No

• 3Com Fast Etherlink/Etherlink III Bus Master

cUnder the heading "Select the driver for your network board", insert

the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\CLI-

ENT." (If you have an HP preloaded HDD, set path to "C:\Masters\Lan-

Drv\3C590\NETWARE\CLIENT\)

dPress "Enter" to continue the installation.

eWhen prompted, insert the corresponding disks to complete file trans-

fer and driver installation.

fWhen the install utility is finished, press <CRTL><ALT><DEL> to re-

start the machine.

gAfter windows loads, open the "NETWORK" folder, double-click the

"NETWORK SETUP" icon.

hSelect "Networks" and verify that "Novell Netware (Workstation Shell

4.0 and above)" is selected under "Install Windows support for the fol-

lowing network only:"

iSelect "OK" twice, and the installation is complete.

7Execute INST_DOS.EXE and enter Yes to accept the agreement.

Andere Handbücher für Vectra VEC 7

Dieses Handbuch passt für folgende Modelle

Andere HP PCI-Karte Handbücher

HP Vectra VL6 7 Bedienungsanleitung

HP A6826A Anleitung zur Verwendung

HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

HP Vectra VEi 7 Bedienungsanleitung

HP Model 748 - VME Workstation Bedienungsanleitung

HP 673642-B21 Bedienungsanleitung

HP FC HBAs Installationsanleitung

HP NC570C Bedienungsanleitung

HP Edgeline EL1000 Bedienungsanleitung

HP Vectra VL410 Bedienungsanleitung

HP Compaq Pro 6305 Bedienungsanleitung

HP FX 3500 Installationsanleitung

HP Vectra VL6 8 Bedienungsanleitung

HP PCIe 2-Port 10GbE Bedienungsanleitung

HP StorageWorks fca2384 Bedienungsanleitung

HP NC380T Gebrauchsanweisung

HP NC1020 Gebrauchsanweisung

HP Vectra VE6 8 Bedienungsanleitung

HP Thunderbolt 3 Bedienungsanleitung

HP AB465A Bedienungsanleitung

HP VL600 - Vectra - 128 MB RAM Bedienungsanleitung

HP 435508-B21 Gebrauchsanweisung

HP Vectra VEi 7 Bedienungsanleitung

HP A7173A Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung