ICP DAS USA ET-2260 Bedienungsanleitung

English / Sep. 2015 / Version 1.0

T-

-2

The eSearch Utility can be obtained from either the companion CD-ROM or

from the ICPDAS website, as indicated below:

CD:\NAPDOS\software\eSearch\

http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/esearch/

Double-click the “eSearch_vxxx_setup.exe”file icon to execute the driver installation.

Click the “Next>”button to start the installation.

Select the destination location. The default path is C:\ICPDAS\eSearch. Verify that the destination

path is correct and click the “Next>”button.

Click the “Next>”button to continue.

Click the “Finish”button to complete the installation.

t’

’s

The package includes the following items:

ET-2260 Module Quick Start Guide (This Document) Companion CD

Pin Assignments:

Wire Connections:

(0xxxx) DO Address:

Starting

Address

Points

Description

Bits Per

Point

Range

Access

Type

0 (0x0)

1 ~ 6

Digital Output Channels

0: OFF, 1: ON

R/W

32 (0x20)

Clears the status of all high latched DI

channels

1: Clear

33 (0x21)

Clears the status of all low latched DI

channels

1: Clear

190 (0xBE)

1 ~ 6

Enables frequency measurement for all DI

Channels

0: Disable

1: Enable

(Default: 0)

R/W/F

235 (0xEB)

1 ~ 6

Sets the Power-on value for all DO Channels

0: OFF, 1: ON

(Default: 0)

R/W/F

267 (0x10B)

1 ~ 6

Sets the Safe value for all DO Channels

0: OFF, 1: ON

(Default: 0)

R/W/F

“R”: Read; “W”: Write; “F”:Settings are recorded in flash memory by default

(1xxxx) DI Address:

Starting

Address

Points

Description

Bits Per

Point

Range

Access

Type

0 (0x0)

1 ~ 6

Digital Input

0: OFF, 1: ON

32 (0x20)

1 ~ 6

Digital Latched Status (High)

0: NO

1: Latched

64 (0x40)

1 ~ 6

Digital Latched Status (Low)

0: NO

1: Latched

“R”: Read

For detailed information related to DI/DO Modbus Addresses, refer to Section 6.3 "Modbus

CD:\NAPDOS\ET2200\document\

http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/

Ensure that the network settings on the Host PC have been correctly configured and are

functioning normally. Ensure that the Windows firewall or any Anti-Virus firewall is properly

configured to allow incoming connections, or temporarily disable these functions, otherwise the

“Search Servers” function in the eSearch Utility described in Section 7 may not perform as expected.

Contact the System Administrator for instructions of how to do this.

Connect both the ET-2260 module and the Host PC to the same sub network or the same Ethernet

Switch.

Apply power to the ET-2260 module. The valid power voltage range is from +10 to +30 VDC.

Verify that the “PWR”LED indicator on the ET-2260 module

is flashing.

-T

A tip for connecting the wire to the connector

A tip for removing the wire from the connector

Connect the NO0 pin (Pin01) to the GND pin (Pin02).

Connect the COM0 pin (Pin03) to the DI0pin (Pin04)

1. Use the blade of the

flat-head screwdriver to

push down the wire

clamp.

Insert the wire

Continue holding the

screwdriver in place

2. While holding the

screwdriver in place,

insert the wire into the

terminal block.

1. Use the blade of a

flat-head screwdriver to

push down the wire

clamp.

Remove the wire

Continue holding the

screwdriver in place

2. While holding the

screwdriver in place,

remove the wire from the

terminal block.

Execute the eSearch Utility and click the “Search Servers” button to search for the ET-2260

module.

Once the search process in complete, double-click the name of the ET-2260 module to open the

“Configure Server (UDP)” dialog box.

Enter the relevant values for the IP Address, Subnet Mask and Gateway, etc., and then click the

“OK” button. The new settings for the

ET-2260 module will take effect within 2

seconds. If the correct network

configuration information is unknown,

contact the Network Administrator to

obtain the relevant details.

Wait for 2 seconds and then click the “Search Servers” button again to ensure that the ET-2260

module is operating correctly using the new configuration.

Click the name of the ET-2260 module to select it.

Click the “Web”button to log in to the web configuration pages.

Factory Default Settings for

the ET-2260 Series:

192.168.255.1

Gateway

192.168.0.1

Mask

255.255.0.0













-T

Once the login screen is displayed, enter the password in the login password field (use the default

password is “Admin”), and then click the “Submit” button to enter the configuration web page.

Click the “Home”tab to access the DI/DO settings page for the ET-2260 module. This page allows a

simple test to be performed to verify the Digital Input/Output functionality.

In the “Set DO Value”section, check the checkbox for “bit0”to set DO0 to ON.

Click the “Update Settings”button to save the revised settings to the ET-2260 module.



Factory Default

Password: Admin







Once the new settings have been saved, the page will be refreshed to indicate the new values.

Verify that the status for the both DO0 and DI0 is shown as “ON”.

ET-2260 Product Page:

http://www.icpdas.com/root/product/solutions/remote_io/ethernet_io/petl-7000_tpet_tet/et-2260.html

Documentation:

CD:\Napdos\ET2200\Document

http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/

Firmware:

CD:\Napdos\ET2200\Firmware

http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/firmware/

NS-205 and DP-665 Product Page (Optional):

http://www.icpdas.com/root/product/solutions/industrial_ethernet_switch/ns-205.html

http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm



Andere Handbücher für ET-2260

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA PROFI-5045 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8092F Stücklistenhandbuch

ICP DAS USA

ICP DAS USA tSH-725 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7000 series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-3033 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7069 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7016 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tZT-P4C4 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-87P2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7067D Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-P3R3 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PETL-7060 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7083 Bedienungsanleitung

ICP DAS USA

ICP DAS USA MN-3253 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PDS-5000 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tSH-700 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA LP-8 21 Series Allgemeine Anweisungen

ICP DAS USA

ICP DAS USA ZT-2055 Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3227 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-3133i Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7016D Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-7552-M Bedienungsanleitung

ICP DAS USA

ICP DAS USA MDC-700 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung