Insportline IN 4071 Verge Bedienungsanleitung

Owner’s manual – EN

IN 4071 Inc inSPORTline Verge

Parts Listing

The following parts list describes all of the parts

illustrated on the exploded diagram on the following

page. Please note, most of these parts are already pre-

assembled on your unit.

Part# Description Part# Description

01 Front Leg Tube 25 Hex Bolt (M10x30 mm)

02A-R

Right Cross Support Bracket

Hex Bolt (M6x50 mm)

02A-L

Left Cross Support Bracket

Hex Bolt (M10x25 mm)

03A

Rear Base

Hex Bolt (M6x45 mm)

Adjustable Ankle Brace

Lock Nut (M10)

05A

Height Adjustment Tube

Lock Nut (M6)

Adjustable Pivot Bar

Square Inner Plug (30 mm)

07B

Backrest Frame

Curved Washer (M6)

Adjustable Foot Tube

Washer (M6)

Spring

Washer (M10)

Square Inner Plug (32 mm)

Small Pin

Bumper

Safety Strap with Buckle

Ankle Brace Tube

Safety Hook

13R

Right Hand Rail

Hex Bolt (M10x35 mm)

13L

Left Hand Rail

Grip Tape

Foam Grip

Pivot Bracket

15R

Right Cover

Plastic Washer (M6)

15L

Left Cover

Safety Lock

Round Inner Plug

Lock Nut (M8)

Plastic Clip

Hex Bolt (M8x35 mm)

Ankle Brace Lock Pin

Washer (M8)

Height Selector Lock Pin

Inner Plug (40x20 mm)

Foam Roller

Bolt (M6x15 mm)

Round Inner Plug (19 mm)

Square Inner Plug (35 mm)

Inner Plug (53x23 mm)

Safety Lock Pin

Knob Bolt

Hex Bolt (M6x10 mm)

24B

Back Rest

Exploded Diagram

The following diagram is provided to help you familiarize yourself with the parts and hardware

that will be used during the assembly process. Please note that not all of the parts and hardware

you see here will be used while you are assembling the machine because some of these items are

already pre-installed. Please continue to the next page to begin the assembly process and use this

page only as a reference guide for parts and hardware.

Assembly

Instructions

Assembly Step 1

A.) A-Frame Assembly

Open the pre assembled A-Frame, which is composed

of parts (#01), (#02A-R/L) and (#03A). Make sure that

two Cross Support Brackets (#02A-R/L) are fully

extended

and ﬁrmly locked

place

pressing

down on them.

B.) Hand Rail Assembly

Align the top hole located on the Rear Base (#03A)

with the top hole located on the Pivot Bracket

(#40). Position the Right Hand Rail (#13R)

on the outside of the Rear Base (#03A) and

position one Safety Hook (#37) on the inside

of the Pivot Bracket (#40)

Insert a Hex Bolt

(#38) through a Washer (#34) followed by the

Safety Hook (#37), Pivot Bracket (#40)

Rear Base

(#03A), Right Hand Rail (#13R), Washer

Align the lower hole located on the Rear Base A

(#03A) with the lower hole located on the Pivot

Bracket (#40) and the lower hole located on

the Right Hand Rail (#13R).

Insert

a Hex Bolt (#25)

through a Washer (#34) followed by the Pivot Bracket

(#40), Rear Base (#03A)

Right Hand Rail (#13R)

Washer (#34) and secure it with one Lock Nut (#29).

Repeat this process on the opposite side. Please look at the

diagrams and make sure

you assembled all of the parts as illustrated.

Assembly

Instructions

Assembly Step 2

A.)

Cover

Assembly

Slide the Left Cover (#15L) and Right Cover (#15R) onto

the left and right of the Hand Rail (#13R/L).

B.)

Adjustable

Pivot

Bar

Assembly

Each Adjustable Pivot Bar (#06) has three adjust able holes in it.

These three holes are designed to be a fine -tune adjustment that

will allow you to shift your center of gravity,

so that you can easily control the rate of inversion. Insert each of

the two Adjustable Pivot Bars (#06) into the slots located on the

Back Rest Frame (#07B) ensuring that they both line up to the top

holes. Proceed with these instructions for now and if you are not

satisfied with the amount of control you have during the inversion

process, please return to this step and move the Adjustable Pivot

Bars (#06) down to the

second hole or to the lowest hole and try again. A

NOTE: EACH HANDLE BAR SHOULD BE PROPERLY

SEATED INSIDE EACH BRACKET. A BRACKET PIN

SHOULD ENGAGE THE HOLE OF EACH HANDLE BAR.

BOTH HANDLE BARS SHOULD ALWAYS BE SET TO

THE SAME POSITION.

Insert a Bolt (#47) and a Washer (#33) through the bottom of both

Adjustable Pivot Bars (#06) and secure it with a Washer (#33) and

a Lock Nut (#30). Insert a Lock Pin (#49) on the top of both the

Adjustable Pivot Bars (#06) . This is for an additional safety

measure.

C.)

Back

Rest

Frame

Assembly

Open the Safety Hooks (#37) on the brackets located on the A-

FRAME. With the help of an assistant, lift the Back

Rest Frame (#07B) and align the Adjustable Pivot Bars (#06) B

into the two slots. Make sure both sides are properly seated into each

slots. Do not be alarm if the frame does not fit perfectly in the slot.

Have your assistant pry apart the handle bars to align it for a perfect

fit. Test the Back Rest Frame (#07B) by rocking it back and forth a

few times. After you have ensured that the Back Rest Frame (#07B)

rotates smoothly, lower the Safety Hooks (#37) over the Adjustable

Pivot

Bars (#06) as far as they will go. Once the Safety Hooks (#37) are

secure, insert Hex Bolts (#50) into the Pivot Brackets (#40) to lock

the Safety Hooks (#37) in place.

Assembly

Instructions

Assembly Step 3

A.) Adjustable Ankle Brace Assembly Take the illustrated

assembly which is composed of parts (#04),(#05A) and (#18)

out of the box. Pull up the Ankle Brace Lock Pin (#18) as

illustrated and, at the same time, pull the Adjustable Ankle

Brace (#04) out

of the Height Adjustment Tube (#05A) SLOWLY. (You will

notice that there is a Spring (#09) that pulls downward as you

pull the Adjustable Ankle Brace (#04) out).

After you get the Adjustable Ankle Brace (#04) out

completely, rotate it 90 degrees counter-clockwise

so that the holes face toward the Ankle Brace Lock Pin

(#18). Insert the Adjustable Ankle Brace (#04) back into

the Height Adjustment Tube (#05A).

B.) Adjustable Ankle Brace Assembly II

Release

the Ankle Brace Lock Pin (#18).

The assemblyshould

looklike

drawing B

after

C.) Ankle Brace Tube Assembly

Slide the Ankle Brace Tube (#12) through the Height

Adjustment Tube (#05 )

05A

Ankle Brace Tube (#12)

Lock Nut (#30).

05A

Note: The holes on these parts must line up in

order for the Bolt (28) to go through.

Assembly Instructions

Assembly Step 4

A.) Foam Roller Assembly

Slide the two Foam Rollers (#20) onto the

Adjustable Ankle Brace (#04) and another two on

the Ankle Brace Tube (#12). Apply soapy water to

the tubes if the foam rollers do not slide on easily.

B.) Adjustable Foot Tube Assembly Remove the Knob Bolt

(#23) from the Height Adjustment Tube (#05A) and set it

aside. Slide the Adjustable Foot Tube (#08) in the Height

Adjustment Tube (#05A) and secure it with the Knob Bolt

(#23).

The Adjustable Foot Tube (#08) is designed to accommodate

different shoe sizes by moving up for smaller feet and down

for larger feet. Please adjust it to accommodate your foot size

accordingly before inverting (ALWAYS WEAR ATHLETIC

SHOES BEFORE INVERTING).

C.) Height Adjustment Tube Assembly With the help

of an assistant, attach the Height Adjustment Tube

(#05A) to the Backrest Frame (#07B) by pulling the

Height Selector Lock Pin (#19) out and simultaneously

sliding the Height Adjustment Tube (#05A) in.

Release the Height Selector Lock Pin (#19) at any

setting for now. Please note, the Height Adjustment

Tube (#05A) is designed to accommodate the height of

various users; set it accordingly by pulling the Height

Selector Lock Pin (#19) as you slide the Height

Adjustment Tube (#05A) up or down. The assembly

process is now complete. Please read the rest

of the manual to learn about the safety features and

operation procedures.

05A

D.) Plastic Clip Footing Assembly Ensure that

two Plastic Clip (#17) footing is installed on the

Front Leg Tube (#01) and Rear Base

(#03$)

before using the unit.

If for any reason they are not installed on the

unit, follow these simple steps to install them. First,

lift the front end up and you will notice that there is a

hole on the bottom. Insert the clip pin on the Plastic

Clip (#17) into the hole on the Front Leg Tube (#01)

and snap it into place. Repeat this process to the

Rear Base (#03

)

if neccessary.

03A 17

17 D

Safety Instructions

WARNING: 250 lb. WEIGHT CAPACITY

DO NOT USE THIS INVERSION TABLE WITHOUT A PHYSICIAN'S APPROVAL IF YOU HAVE ANY OF THE

FOLLOWING CONDITIONS

(this list is for reference only, it is not an exhaustive listing):

Pregnancy, Hiatal Hernia, Ventral Hernia, Glaucoma, Retinal Detachment or Conjunctivitis; High Blood Pressure, Hypertension,

recent Stroke or Transient Ischemic Attack; Heart or Circulatory Disorders for which you are being treated; Spinal Injury; Cerebral

Sclerosis; Acutely Swollen

Joints; Bone Weakness (Osteoporosis), recent unhealed fractures, medulary pins and/or surgically implanted orthopedic supports; the use

of anticoagulants, including high doses of aspirin; Middle Ear Infections; Extreme Obesity.

IF YOUR PHYSICIAN PERMITS YOU TO USE INVERSION THERAPY, DO SO UNDER THEIR DIRECTION AND

HAVE OUR GUIDELINES APPROVED BY YOUR PHYSICIAN.

DO NOT LET CHILDREN USE THE INVERSION TABLE UNSUPERVISED.

THERE ARE CERTAIN PEOPLE WHO SHOULD NEVER INVERT. IF YOU THINK YOU BELONG TO THIS MINORITY,

PLEASE CHECK WITH YOUR PHYSICIAN BEFORE USING THIS INVERSION TABLE.

IMPORTANT:

LOCK SAFETY HOOKS (#37) IN PLACE BEFORE USE.

Safety Lock

There is a Safety Lock

#42 Safety

ock#43

ock

Nut (M8)

ADJUST TO YOUR HEIGHT

(Start at 2-3" taller than your actual height)

(#42) included to lock the

inversion system when not in

use. This lock slides into the

Height

Adjustment Tube (#05

) and then

into the frame. Use a Lock Nut

(#43) to secure the Safety Lock

(#42) and tighten it with a

wrench to keep children

[

piece]

05A 43

[

piece]

Secure your ankles by Adjusting top rollers (using pull

pin) as close to bottom rollers as possible.

BE SURE PULL PIN LOCKS INTO PLACE IN

ORDER TO SECURE ANKLES!

from using the inversionsystem.

Usage Guidelines

ATTACH THE SAFETY STRAP TO THE NYLON COVERED STEEL

FRAME.

The buckle of the Safety Strap should be positioned about

KDOIZD\

down the Strap with the concave side facing up. The two ends of

the buckle should show; the middle slot should be covered up by the Strap. Feed the

free end of the Strap through the buckle under one end, over the middle and under the

other end. The buckle should be able to slide on the Strap so that you can adjust the

length of the Strap loop.

The shorter the strap, the less the angle of inversion. The longer the strap, the

greater the inversion angle.

First time users should adjust the tether strap by shortening it for minimal

inversion.

THE FIRST TIME THAT YOU USE THIS INVERSION TABLE, HAVE

SOMEONE WITH YOU TO WATCH YOU. ALTHOUGH THE INVERSION

TABLE IS EASY TO USE, HAVING SOMEONE NEARBY TO “SPOT” YOU

WILL PROVIDE YOU WITH COMFORTAND ENSURE YOU HAVE THE

CORRECT INITIAL SETTINGS.

Before starting, ensure that the Inversion Table is at the correct settings to match your

height and weight. As each individuals’ body type is different, you will need to find

the correct settings for you personally.

ENSURE THATALL PULL PINS ARE TIGHTAND ENTIRELY IN THE

HOLES.

ALWAYS MAKE SURE THAT THE SAFETY STRAP IS

ATTACHED.

AVOID INVERTING AFTER MEALS.

Usage Guidelines

05A

The settings for height range from 4'7" (140cms) to 6'5" (196cms).

To adjust the Inversion Table for the correct height setting; Pull out the Height

Selector Lock Pin (#19) and slide the Height Adjustment Tube (#05A) until the

desired height is shown just below the sleeve.

As everyone's body is different, not all 5'9" people will ultimately use the 5'9" setting.

Your correct setting will be determined by a minimal amount of testing (Explained

further in the USAGE section of this manual).

ALWAYS USE THE INVERSION TABLE UNDER SUPERVISION UNTIL

YOU FEEL COMFORTABLE WITH THE PRODUCT.

Set the Height Adjustment Tube (#05A) to your height (or just above

your height).

Stand on the Adjustable Foot Tube (#08) with the back of your ankles resting and

centered on the rear foam rollers.The position of the Adjustable Foot Tube (#08)can be

adjusted by removing the Knob.

Bolt (#23)

Adjust the Adjustable Ankle Brace (#04) by adjusting Ankle Brace

18 Lock Pin (#18) so that the Foam Rollers are snug but comfortable across the front of

your ankles and top of your feet.

MAKE SURE THAT THE SAFETY STRAP IS ATTACHED.

Inhaltsverzeichnis

Andere Insportline Fitnessgeräte Handbücher

Insportline

Insportline IN 14147 Bedienungsanleitung

Insportline

Insportline AF5004 Bedienungsanleitung

Insportline

Insportline Airstunt IN 21989 Bedienungsanleitung

Insportline

Insportline IN 20848 Bedienungsanleitung

Insportline

Insportline AB Perfect Bedienungsanleitung

Insportline

Insportline LCR1102 Bedienungsanleitung

Insportline

Insportline LCR1103 Bedienungsanleitung

Insportline

Insportline Hero B80 Bedienungsanleitung

Insportline

Insportline IN 21393 Bedienungsanleitung

Insportline

Insportline MegaSpin Bedienungsanleitung

Insportline

Insportline IN2185 Bedienungsanleitung

Insportline

Insportline IN 12075 Bedienungsanleitung

Insportline

Insportline IN 561 Bedienungsanleitung

Insportline

Insportline AcroBar 25979 Bedienungsanleitung

Insportline

Insportline IN 7280 Bedienungsanleitung

Insportline

Insportline Verticon Pro 500 Bedienungsanleitung

Insportline

Insportline IN 1794 Bedienungsanleitung

Insportline

Insportline Squo IN 21715 Bedienungsanleitung

Insportline

Insportline 7153 Bedienungsanleitung

Insportline

Insportline IN 4071 Bedienungsanleitung

Insportline

Insportline RK200 Bedienungsanleitung

Insportline

Insportline Verticon 21964 Bedienungsanleitung

Insportline

Insportline Holister Bedienungsanleitung

Insportline

Insportline Gardian G8 IN 13970 Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung