Interlogix UltraView UVD-6130VE-2 Series Bedienungsanleitung

UltraView UVD-6130VE-2

WDR Dome Camera User

Manual

P/N 1072549A • REV 1.0 • ISS 18JUN12

Trademarks and

patents

The

TruVision and Interlogix names and logo are trademarks of

UTC

Fire & Security.

Other trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products.

Manufacturer

UTC Fire & Security Americas

Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

FCC compliance

Class A:

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated i

n a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own

expense.

ACMA compliance

Notice!

This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

European Union

directives

12004/108/EC (EMC directive):

Hereby, UTC Fire & Security

declares that this device is in compliance or with the essential

requirements and ot

her relevant provisions of Directive 2004/108/EC

2002/96/EC (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local supplier

upo

n the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info.

Contact information

For contact information

, see www.utcfireandsecurity.com or

www.utcfssecurityproducts.eu

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 1

Content

Product overview 2

Package Contents 2

Features 2

User guidelines 3

Product description 3

OSD control pad 3

Installation 5

Mount the camera 5

Connect the cables 5

Adjust the lens 5

Adjust the focus and zoom 6

Programming 7

Access the Setup menu 7

Select the lens type 8

Set shutter/AGC 8

Adjust the picture characteristics 10

Set white balance 10

Set WDR 11

Set image noise reduction 12

Set HLC and BLC 12

Set Day/Night mode 13

Set E-zoom 14

Set DIS 14

Set the privacy mask area 14

Set motion detection 15

Display the synchronization mode 15

Set the camera ID 16

Select the language 16

Reset camera settings 16

Save all changes 16

Specifications 17

Dimensions 17

Menu Map 18

2 UltraView UVD-6130VE-2 WDR Dome Camera User Manual

Product overview

The UVD-6130VE-2 WDR camera uses a digital signal processor (DSP) to

process video signals. The camera includes a microcontroller to provide high-

quality images with high-color reproduction and sharp pictures.

Package Contents

The package contains the following:

• Dome camera

• Monitor output cable

• Mounting screws, wall anchors, and hex wrench

• Power terminal

• Ceiling drilling holes template

• Quick start guide

Note: Use the video output BNC and power jack for normal system operation.

Use the monitor output cable for installation and maintenance.

Features

The camera includes the following features:

• Super HAD II (hole accumulated diode) technology with 480,000 pixels NTSC

(570,000 PAL)

• Use of LSI (large scale integration) digital processors to produce 650 lines of

horizontal resolution

• Smart digital control automatic BLC (backlight compensation)

• WDR (wide dynamic range)

• Advanced auto exposure system for both fixed iris and auto iris lenses to

optimize the amount of light

• Internal synchronization

• Eight privacy mask areas to protect privacy concerns

• Advanced OSD (onscreen display) control

• Signal-to-noise ratio better than 52 dB

• Long life and high reliability

• Isolated switching power 12 VDC and 24 VAC

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 3

User guidelines

• Program the camera settings as much as possible before mounting the

camera. Take appropriate safety precautions while completing programming

after installation.

• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the

camera.

• Do not use the camera over the temperature range specifications: -10°C to

+50°C (14°F to 122°F)

• If the light source where the camera is installed experiences rapid, wide-

variations in lighting, the camera may not operate as intended.

WARNING: To reduce the risk of fire or electronic shock, do not expose the

camera to rain or moisture and do not remove the cover or back.

Product description

Figure 1:: Camera description

Camera body

OSD control

pad

System heater

Power jack

Monitor output cable:

1. Monitor output BNC; 2.

Monitor output RCA

Video monitor output Video output BNC

OSD control pad

The onscreen display (OSD) control pad (Figure 3) is a five-direction pad that

provides the ability to manually control the camera functions. Table 1 below lists

the OSD control pad functions and describes their use.

4 UltraView UVD-6130VE-2 WDR Dome Camera User Manual

Figure 2: OSD control pad

OSD control pad

Table 1: OSD control pad functions

Pad directions Description

Up Moves the cursor upward to select an item.

Left Moves the cursor left to select or adjust the options of the selected

item.

Right Moves the cursor to the right to select or adjust the options of the

selected item.

Down Moves the cursor downward to select an item.

Enter

Press the center of the control pad to display the Setup menu. If the

selected item has its own menu, press the control pad to enter a

submenu. Press the control pad for 2 seconds to save all settings

and exit the Setup menu.

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 5

Installation

Please check the package contents and make sure that the device in the

package is in good condition and all the assembly parts are included.

To install the camera you will need to prepare the mounting surface, mount the

camera, make cable connections, adjust the lens and then secure the dome

cover securely.

Note: Before installing, please ensure that the mounting surface is strong enough

to withstand three times the weight of the camera. If the mounting surface is not

strong enough, the camera may fall and cause serious damage.

Mount the camera

Use the ceiling drilling holes template and mark the holes on the ceiling with a

pen. Attach the plate with fasteners to the ceiling and then attach the camera

body to the plate.

To mount the camera, attach the camera to the mounting surface using the

appropriate fasteners.

Connect the cables

To connect the cables:

1. Connect a coaxial cable from the camera’s BNC connector to a CCTV

monitor or video recording device.

2. Connect the 12 VDC or 24 VAC power supply to the power jack of the

camera.

Caution: Check for polarity when using a 12 VDC power supply.

Adjust the lens

The camera is mounted on a pan-tilt-twist (3-axis grimbal) rotating platform so

that it is easy to adjust the camera orientation. See Figure 3 on page 6.

6 UltraView UVD-6130VE-2 WDR Dome Camera User Manual

Figure 3: Camera adjustment

Platform horizontal adjustment (0 to 180°)

Platform vertical adjustment (0 to 90°)

Rotor horizontal adjustment (0 to 350°)

To adjust the lens:

See Figure 3 above.

1. To adjust the horizontal angle of the platform up to 180 degrees, turn the

platform.

2. To adjust the horizontal angle of the rotor up to 350 degrees, turn the rotor on

the platform.

3. To adjust the vertical angle of the platform up to 90 degrees, turn the

platform.

Adjust the focus and zoom

Figure 4: Zoom and focus adjustment

Zoom ring thumbscrew

Focus ring thumbscrew

To adjust the camera zoom and focus:

1. Loosen the zoom ring thumbscrew and turn the zoom ring to set the desired

zoom. Tighten the thumbscrew.

2. Loosen the focus ring thumbscrew and turn the focus ring to set the desired

focus. Tighten the thumbscrew.

UltraView UVD-6130VE-2 WDR Dome Camera User Manual 7

Programming

Once the camera hardware has been installed, the camera can then be

configured.

Access the Setup menu

The Setup menu provides access to the camera configuration options. The on-

screen display (OSD) is only available in English.

Program the camera by attaching a standard video monitor to the system.

Figure 5: The Setup menu screens

Table 2: Setup menu description

Menu item Description

Lens Defines the camera ID, mirror, and digital noise reduction (DNR) set up.

Shutter/AGC Defines the method of iris control.

Pict Adjust Defines the image quality functions.

White Bal Defines the white balance (WB) set up.

WDR Defines the wide dynamic range (WDR) set up.

NR Defines the digital noise reduction level.

BLC/HLC Defines the highlight compensation (HLC) and backlight compensation

(BLC) set up.

Day/Night Defines the day/night (D/N) set up.

EZoom Enables/disables digital zoom.

DIS Enables/disables the digital image stabilizer.

Privacy Defines privacy mask set up.

Motion Det Defines the motion detection set up.

Sync Displays the current synchronization mode.

Camera ID Defines the camera ID displayed on-screen.

Language Defines the language of the OSD.

Camera Reset Resets the camera to factory default settings.

Save All Saves changes made.

Exit Exits the menu and returns to live mode.

8 UltraView UVD-6130VE-2 WDR Dome Camera User Manual

To access the Setup menu:

1. Press the OSD control pad (Enter) to access the Setup menu and its

submenus.

2. Push the pad up, down, left and right to move between menu options.

3. Press the OSD control pad to select an option.

4. When in a sub menu, select Return to return to the previous menu.

5. To save configuration changes, move the cursor to Save All at the bottom of

the screen and press Enter

6. To exit a menu and return to live mode, move the cursor to Exit at the bottom

of the screen and press Enter.

Select the lens type

In the Setup menu, go to Lens and select the type of lens used with the camera,

Auto or Manual. Select Manual for a manual lens and adjust the options

manually, or select Auto to set the lens type to autoiris. The Autoiris menu

appears.

Autoiris menu:

Type: Select the drive mode of the lens. Only DC is available.

Mode: Select the iris control mode. Auto (automatically controlled depending on

the light), Open (always open), or Closed (always closed).

Speed: When the mode is set to Auto, select the convergence speed of the iris

between 0 and 255.

Set shutter/AGC

In the Setup menu, go to Shutter/AGC and select the required iris control option:

Manual, Auto or Traffic. Auto is default. The selected menu appears:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Interlogix Sicherheitskamera Handbücher

Interlogix

Interlogix TruVision TVD-2402 Bedienungsanleitung

Interlogix

Interlogix TVP-6102 Bedienungsanleitung

Interlogix

Interlogix UVP-M1120P-18X-N Bedienungsanleitung

Interlogix

Interlogix TVB-WBS Bedienungsanleitung

Interlogix

Interlogix UVD-XP4DNR(-P) Bedienungsanleitung

Interlogix

Interlogix TruVision TVB-2401 Bedienungsanleitung

Interlogix

Interlogix TruVision TVP-5101 Merkblatt

Interlogix

Interlogix TruVision Series Bedienungsanleitung

Interlogix

Interlogix 4 SERIES Merkblatt

Interlogix

Interlogix TruVision TVB-2401 Bedienungsanleitung

Interlogix

Interlogix TruVision HD-TVI 3MPX Merkblatt

Interlogix

Interlogix TruVision Bullet IR Bedienungsanleitung

Interlogix

Interlogix TruVision TVD-2401 Bedienungsanleitung

Interlogix

Interlogix TruVision TVB-6102 Bedienungsanleitung

Interlogix

Interlogix TVB-5501 Bedienungsanleitung

Interlogix

Interlogix UVC-XP4DN-HR-P Bedienungsanleitung

Interlogix

Interlogix TVF-1101 Bedienungsanleitung

Interlogix

Interlogix TruVision TVD-7120VE-2 Bedienungsanleitung

Interlogix

Interlogix FW5.1 Bedienungsanleitung

Interlogix

Interlogix TruVision TVT-2103 Bedienungsanleitung

Interlogix

Interlogix UltraView Bedienungsanleitung

Interlogix

Interlogix UVD-XP4DNR Bedienungsanleitung

Interlogix

Interlogix TruVision PTZ 36X Bedienungsanleitung

Interlogix

Interlogix TruVision Open Standards Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung