Kaba E-PLEX 3x65 Deadlatch/Exit Mortise Bedienungsanleitung

INSTALLATION INSTRUCTIONS

E-PLEX®3X00 SERIES NARROW STILE LOCK

TABLE OF CONTENTS

E-PLEX 3x65 Deadlatch/Exit ortise odel

E-PLEX 3x66 Deadbolt/Swing Bolt ortise odel

This lock is designed to function with new or existing Adams Rite®Hardware

for Deadlatch, Deadbolt, and Exit applications. These Adams Rite Hardware

models (1850, 1950, 4500, 4700, 4900, MS1850S, MS1950S, and 8400 Series)

are sold separately. The specific applications for this model are for narrow stile

aluminum and glass doors, 2” minimum width and 1 3⁄4” thick.

Shipping Package Includes (See Figure 1):

• (1) E-Plex 3x00 Lock Assembly

• (1) Outside Lever (Lever Model Only)

• (1) Screw Pack

• (1) Battery Housing with four AA Batteries (alkaline)

• (2) Keys (Schlage C or Kaba 90 Keyway)

• Documentation pack consists of:

(1) Installation Instructions (this manual)

(1) Operations Manual

(1) Lock Set-up Guide

(1) Quick-Reference Guide

a. 54579–Upper Mounting Screws (2)

b. 44229–Mounting Bushings (4)

c. 54275–Lower Mounting Screws (2)

d1. 75271–Kaba Cam Plug Deadlatch (1)

d2. 75262–Kaba Cam Plug Deadbolt (1)

e1. 75272–Lock Assembly for Lever (1)

e2. 75273–Lock Assembly with Thumbturn (1)

f. 54725–Pinned Torx Screw (2)

g. 34298–Lever Cap (1)

h. 34309–Lever (1)

i. 44226–“D” Bushing (2)

j. 54685–Battery Pack (1)

k. 24554–Battery Cover (1)

l. 54725–Pinned Torx Screws (1)

ToolsRequired .................................................................3

A. Door Preparation - Remove Existing Outside Hardware . . . . . . . . . . . . . . . . . . . . . . . . . .3

B. StilePreparation ...........................................................5

C. LockPreparation ...........................................................6

D. LockInstallation ...........................................................13

E. StandardOperationsProcedures.............................................15

Figure 1

WARNING: This loc is designed to be used with Adams

Rite®brand hardware only. Improper use or installation of

this product will void the warranty.

LEVER LOCK ONLY

TOOLS REQUIRED

• Power Drill with 3⁄8” (10mm) drill bit

• Tape

• Center Punch or Awl

• Hex Allen Wrench Set

• Phillips Head Screwdriver

• Small Flat Blade Screwdriver

• Safety Glasses

A. DOOR PREPARATION—RE OVE EXISTING

OUTSIDE HARDWARE

A-1 Remove any existing Outside Hardware such as Lever Entry Trim, Latch

Pull, Key Cylinders, etc.

A-2 Remove and retain the screws and Armored Face Plate (Scalp) from the

face of the Deadlatch (See Figure 2A) or Deadbolt (See Figure 2B).

A-3 Loosen the set screw and remove the existing hardware assembled from

the outside to the Deadlatch or Deadbolt Mortise, including the Adams

Rite Cam Plug 4580 (d).

A-4 Set Scalp and screws aside for reassembly later.

Figure 2A

set screw

scalp

screws

Figure 2B

set screw

Disclaimer: While reasonable efforts were made to ensure the accuracy of this document at the time of printing, Kaba

assumes no liability for any errors or omissions. This information is subject to be revised without notice, and changes

may be incorporated in future releases.

scalp

screws

KABA E-PLEX®3x00 SERIES

LI ITED WARRANTY

KABA ACCESS CO TROL WARRA TS THIS PRODUCT TO BE FREE FROM

DEFECTS I MATERIAL A D WORKMA SHIP U DER ORMAL USE A D SERV-

ICE FOR A PERIOD OF THREE (3) YEARS. KABA ACCESS CO TROL WILL

REPAIR OR REPLACE, AT OUR DISCRETIO , E-PLEX 3000 SERIES LOCKS

FOU D BY KABA ACCESS CO TROL A ALYSIS TO BE DEFECTIVE DURI G THIS

PERIOD. OUR O LY LIABILITY, WHETHER I TORT OR I CO TRACT, U DER

THIS WARRA TY IS TO REPAIR OR REPLACE PRODUCTS THAT ARE

RETUR ED TO KABA ACCESS CO TROL WITHI THE THREE (3) YEAR WAR-

RA TY PERIOD.

This warranty is in lieu of and not in addition to any other warranty or condition,

express or implied, including without limitation merchantability, fitness for purpose

or absence of latent defects.

ATTE TIO : This warranty does not cover problems arising out of improper

installation, neglect or misuse. All warranties implied or written will be null and

void if the lock is not installed properly and/or if any supplied component part

is substituted with a foreign part. If the lock is used with a wall bumper, the

warranty is null and void. If a doorstop is required, we recommend the use of a

floor secured stop.

The environment and conditions of use determine the life of finishes on Kaba

Access Control products. Finishes on Kaba Access Control products are subject

to change due to wear and environmental corrosion. Kaba Access Control can-

not be held responsible for the deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval. Approvals

and Returned Goods Authorization umbers (RGA umbers) for the E-Plex

3x00 Series are available through our Customer Service department in

Winston-Salem, C (800) 849-8324. The serial number of a lock is required

to obtain this RGA Number. The issuance of an RGA does not imply that a

credit or replacement will be issued.

The RGA number must be included on the address label when material is

returned to the factory. All component parts must be included in the package

with return. All merchandise must be returned prepaid and properly packaged

to the address indicated.

B. STILE PREPARATION

B-1 Install the Kaba Cam Plug d1 or d2 into the Deadlatch or Deadbolt. Face of

Cam Plug must be flush or below the surface of the stile, make sure set

screw is snug but do not tighen it yet. (See Figure 2 on page 3).

Note: Refer to the Adams Rite Cam Plug Instructions for Right Hand/Left

Hand Installations (located in the Screw Pack). (For Deadlatch Models)

B-2 Affix the appropriate model Template to the outside face of the door stile.

Ensure the pins from the Cam Plug are through the proper holes, the tem-

plate is straight and aligned with the edge of the door, and that “TOP” is

facing up and “BOTTOM” is facing down (See Figure 3).

B-3 With a center punch or awl, mark the four drilling points.

B-4 Utilizing a power drill with 3⁄8” drill bit, drill four holes as marked completely

through the door (interior and exterior of the stile). Tip—you may want to

first, drill pilot holes, then drill from each side to keep holes straight

through and minimize burrs.

Figure 3

Flush or

Below

For

Deadlatch

Model, use

template

64782.

For Deadbolt

Model, use

template

64783.

C. LOCK PREPARATION

C-1 On Deadlatch Model only, remove Handing Screw (FIG 4):Caution: The

appropriate handing screw must be removed for proper lock function

after installation.

Inside the battery compartment, the lock comes with both handing

screws installed. Based on the door application handing, Left Hand (LH)

or Right Hand (RH) one screw must be removed as noted in FIG 4.

Deadbolt Models, are shipped with no handing screws attached. They

must be removed for Deadbolt applications.

Note: A RH Deadlatch lock is shown in FIG 4.

For Deadlatch Locks only, orient the lock as shown in FIG 4 (spindle up)

and remove the appropriate shipping screw, left screw for LH or right

screw for RH.

Figure 4

Remove left handing

screw for left hand

application.

Note: Right Hand

application shown,

Left Hand application

would show the lever

on the opposite side. Remove right handing

screw for right hand

application.

Note: Right Hand

application shown.

Spindle Assembly:

Deadlatch—Upper Hole

(Deadlatch assembly

shown)

Deadbolt—Lower Hole

C-2 Battery Pack Installation

Secure the connection end of the Battery Pack to

the Cable Harness. After the connection, the lock

will set itself and you should hear an audible

sound, spinning of the inside motor, and see a

green light—all simultaneously. Upon connection,

place the Battery Pack into the rubber battery

housing, harness connection up, and slide the

assembly into the battery compartment (see Fig

5). Secure in place with the Battery Cover and

Torx Screw.

The lock can now be programmed prior to installa-

tion if desired. Figure 5

Note: If your application requires a change of cylinder, that step should

be done at this time, before installation. If not required, skip to

section D.

KABA ACCESS CO TROL

2941 I DIA A AVE UE

WI STO -SALEM, C 27199-3770

O POSTAGE

ECESSARY

IF MAILED

I THE

U ITED STATES

BUSINESS REPLY AIL

FIRST-CLASS MAIL PERMIT O. 1563

POSTAGE WILL BE PAID BY ADDRESSEE

WI STO -SALEM, C

Thank you for purchasing our product. In order to

protect your investment and to enable us to better

serve you in the future, please fill out this registration

card and return it to Kaba Access Control, or

This lock will be used in what type of facility?

Commercial Building Industrial / Manufacturing Airport

College/University Government/Military School/Educational

Hospital/Healthcare Other (please specify)

What area is being secured with this lock? (e.g. Front Door, Common Door, Exercise Room)

This lock is:

ew Installation

Replacing a conventional keyed lock

Replacing a Kaba Mechanical Pushbutton Lock

Replacing a Kaba Electronic Access Control

Replacing a Keyless Lock other than Kaba

How did you learn about Kaba Access Control Pushbutton Locks?

Advertisement Previous Use Internet / Web Another Use

Locksmith Maintenance Training Class Other (please specify)

What was your reason for buying this lock?

Who installed your lock?

Locksmith Maintenance Other

Check here if you would like more information on Kaba Access Control locks.

ame

Position

Company

Address

City

State ZIP (Postal Code) Country

Phone

ame of Dealer Purchased From

Date of Purchase

Lock Model umber

REGISTRATION CARD

Notes

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kaba Türschloss Handbücher

Kaba

Kaba S-module Bedienungsanleitung

Kaba

Kaba 5 00 Series Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Kaba

Kaba E-Plex 5X10 Bedienungsanleitung

Kaba

Kaba PowerLever 1550 Bedienungsanleitung

Kaba

Kaba SIMPLEX 5000 CYLINDRICAL Bedienungsanleitung

Kaba

Kaba E-PLEX STANDARD Series Bedienungsanleitung

Kaba

Kaba LCLX Bedienungsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5x00 Cylindrical Bedienungsanleitung

Kaba

Kaba Simplex 7104 Series Bedienungsanleitung

Kaba

Kaba SIMPLEX 900 Series Bedienungsanleitung

Kaba

Kaba 1547-K5 Bedienungsanleitung

Kaba

Kaba E-Flash EF780 Bedienungsanleitung

Kaba

Kaba 7102 series Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba E-Flash 680 Bedienungsanleitung

Kaba

Kaba Ilco 790/79 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5900 Bedienungsanleitung

Kaba

Kaba ILCO Generation E-760 Series Bedienungsanleitung

Kaba

Kaba Saflok MT RFID Bedienungsanleitung

Kaba

Kaba Ilco 790 Series Montageanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung