Kaba LCLX Bedienungsanleitung

LOCK MODES

A maximum of two users can exist in a lock. A lock can operate in either Single Mode or

Dual Custody Mode.

Note:

For a UL listed installation, only one user can be activated.

• Single Mode E

Single Mode defaults to having only a Manager User (User 1) in the lock. A second

user (User 2) can then be added by the Manager User (User 1). (See section on

Manager User Operations.)

In Single Mode only one valid user combination is required to open the lock - the Manager

User (User 1) combination or the User 2 combination.

Note:

Default lock status from the factory is Single Mode with an opening

combination of “50 25 50” for the Manager User (User 1).

•Dual Custody Mode EE

Dual Custody Mode defaults to two users in the lock - User 1 and User 2.

Both user combinations are required to open the lock - the User 1 combination and the

User 2 combination.

Note:

Manager User Operations are not available in Dual Custody Mode.

LOCK OPERATING CONVENTIONS

•The LC Series lock models are battery powered (PowerSaverTM Technology.)

• To clear a combination or keystroke, press the ¸¸

¸¸

¸key.

• If the bolt is not retracted within 4-6 seconds after a valid opening combination is

accepted, the lock will “relock”.

• Slide Bolt (Auto Locking) Technology: Once a combination has been entered and

accepted, the lock bolt movement works in conjunction with the bolt works of the

container. When the bolt works are disengaged to open the container, the lock bolt will

slide into the “unlocked” or retracted position. Once the bolt works are extended to the

locked position, the lock bolt automatically slides into the “locked” position. The lock will

not open if force is applied to the end or side of the bolt.

LC SERIES

OPERATING INSTRUCTIONS

MODELS LCLX, LCMX,TLCL,TLCM

Document Number 3032.034 Rev. B - 03/05

LOCK RESPONSES

• Each keystroke generates a green flash

with a beep 8.

• The completion of a step within an operation is indicated by a green flash

with a

beep 8.

• The successful completion of an operation is indicated by a green/red flash with a

beep

• An error is indicated by three red flashes with beeps.

• A low battery is indicated by continuous alternating green and red flashes with

beeps (

8... ) after a lock opening.

• Bolt end pressure is indicated by a maximum of twelve red flashes

followed by a

green/red flash with a beep

8after a correct opening combination has been

entered. If the bolt end pressure is relieved before all twelve red flashes are displayed,

the red flashes will terminate and a green flash with a beep

8will occur

indicating that the lock can now be opened.

• If an attempt is made to initiate an operation that begins with a # on a Model TLC lock

during Time Delay, you will get an error indicator of three red flashes with beeps

8after the first two keystrokesof the operation.

TO UNLOCK

1. • For Single Mode EE

E(Factory combination is “50 25 50”.)

Enter Manager User (User 1) or User 2 combination.

• For Dual Custody Mode EE

EEE

Enter User 1 or User 2 combination.

Enter the second combination.

Wrong Try Penalty: 5 wrong tries =

3 min. lockout

Each additional wrong try = 3 min. lockout

Red flashes with beeps

8will occur during the lockout.

2. Immediately rotate the container handle to retract bolt works before a green/

red flash with beep

8occurs (4 second opening window). Open the

container door. To close and lock the container, close the door and rotate the

container handle back to locked position.

CHANGE COMBINATION

Caution:

Before changing combination, open the container door to allow testing

with the new combination. Record new combination and store it in a secure

place.

1. • For User 1 (Manager User in Single Mode)

Press #. Press 1.

• For User 2

Press #. Press #. Press 1.

• For Courier (Only available on the Model TLC lock.)

Press #. Press #. Press #. Press 1.

2. Enter current combination. (Factory combination is “50 25 50”.)

3. Enter new six-digit combination.

4. Enter new combination again for verification.

5. Open the lock with the new combination before closing container.

CHANGE LOCK MODE (SINGLE / DUAL CUSTODY)

Note:

Changing the lock mode will reset the combination(s) to “50 25 50”. If a

courier exists in the lock, it will be deleted when the mode is changed. For a

Model TLC lock, no change will be made to the Time Delay values.

1. Press #. Press 2.

2. • If changing from Single to Dual Custody Mode

Enter Manager User (User 1) combination.

• If changing from Dual Custody to Single Mode

Enter User 1 or User 2 combination.

Enter the second combination.

SET DELAYTIME AND OPENINGWINDOW*

* This feature is only available on the Model TLC lock.

1.Press #. Press 5.

2. • For Single Mode EE

E(Factory combination is “50 25 50”.)

Enter Manager User (User 1) combination.

• For Dual Custody Mode EE

EEE

Enter User 1 or User 2 combination.

Enter the second combination.

3. Enter number of minutes (01-99) you want to delay lock opening or “00” to disable

time delay.

4. Enter delay time again for verification.

If not “00”, proceed to step 5.

5. Enter number of minutes (01-20) for the delayed opening window.

6. Enter number of minutes for the delayed opening window again for verification.

Note:

A change in delayed opening will not take effect until after the next

opening of the lock.

TO UNLOCK WITHTIME DELAY*

* This feature is only available on the Model TLC lock.

If operating a Model TLC lock with a Delay Time set to something other than 0, red

flashes

will display every 4 seconds after a combination has been entered and will

continue during the time delay.

Green flashes

display with beeps 8to indicate the opening window is active

and will continue during the opening window.

Enter the combination(s) to open the lock before the opening window expires.

If a combination other than a valid Courier combination is entered during the time delay,

you will get an error indicator of three red flashes with beeps.

COURIER OVERRIDE OFTIME DELAY*

* This feature is only available on the Model TLC lock.

If you wish to override time delay on a Model TLC lock with a Delay Time set to something

other than 0, the Courier combination can be entered during the time delay window once

another user has initiated the time delay. If the Courier combination is entered success-

fully, green flashes

will display with beeps 8to indicate the opening window is

active and will continue during the opening window.

Enter the combination(s) to open the lock before the opening window expires.

If the combination entered is not a valid Courier combination, you will get an error

indicator of three red flashes with beeps.

Manager User Operations

These operations are only available in Single Mode and can only be performed by the

Manager User (User 1). All Manager User Operations involve management of User 2 and

the Courier (TLC only).

User 2 can have a lock access status of “Enabled” or “Disabled”. If “Enabled”, User 2

can open the lock. When User 2 is added to the lock, the default lock access status is

“Enabled”. The Manager User (User 1) has the authority to change the lock access

status for User 2. If “Disabled”, User 2 will not have the ability to open the lock.

ADD USER 2

1. Press #. Press 3.

2. Enter Manager User (User 1) combination.

Note:

User 2 is added to the lock as “Enabled” with a factory combination of “50 25 50”.

User 2 can change the User 2 combination while Enabled, but only the Manager User

(User 1) can change the lock access status.

DELETE USER 2

1. Press #. Press 4.

2. Enter Manager User (User 1) combination.

ENABLE USER 2

1. Press #. Press 6.

2. Enter Manager User (User 1) combination.

Note:

If you try to enable User 2 when already enabled, you will get an error indication.

DISABLE USER 2

1. Press #. Press 7.

2. Enter Manager User (User 1) combination.

Note:

If you try to disable User 2 when already disabled, you will get an error indication.

ADD COURIER*

*This feature is only available on the Model TLC lock.

1. Press #. Press #. Press 3.

2. Enter Manager User (User 1) combination.

Note:

The Courier is added to the lock with a factory combination of “50 25 50”. The

combination must be changed before the Courier is enabled to overrideTime Delay.

DELETE COURIER*

* This feature is only available on the Model TLC lock.

1. Press #. Press #. Press 4.

2. Enter Manager User (User 1) combination.

Battery Replacement

Read all instructions before attempting to replace the battery in an LC Series

lock. The battery is located in the keypad assembly.

REPLACE LC BATTERY

To replace the battery, you must

first remove the keypad assem-

bly.

For Lexan lock:

Insert the blade of a flat head

screwdriver under the keypad

housing at a point about 15

degrees to the right of 6 o’clock

on the face of the keypad

(below the Enter key). (See

Figure 1.) There is a small

indentation on the back edge of

the keypad housing that will

allow the screwdriver to easily

be inserted at this point. Pry the

keypad assembly from the face

of the safe being careful not to

damage the cable connection

from the safe to the keypad

assembly. (See Figure 2.)

For Metal lock:

Press the keypad release button

found on the bottom of the

keypad housing.

Remove the old battery and

replace with a new 9-Volt

battery. (See Figure 2.) Reattach

the keypad being careful not to

pinch the battery cable

between the keypad housing

and the mounting bracket.

Test the operation of the lock before closing the container. If the combination is

entered successfully, one green flash displays to indicate the lock is ready to

open. Rotate the container handle to retract the bolt. If the test is successful, the

lock and container are now ready for use.

If the lock does not operate successfully, remove the keypad once again to

check the cable and battery connections.

BatteryClip

Cable

Connection

Figure 2

Battery

Insert Blade of

Screwdriver

Under Keypad

Housing

Figure 1

NOTES

Notice: Information in this document is subject to change without notice. Kaba Mas shall not be liable

for technical or editorial errors or omissions contained herein; nor for incidental or consequential

damages resulting from the furnishing, performance or use of this material.

PowerSaver Technology is a trademark of Kaba Mas Corporation in the United States and/or other

countries.

This product is covered by one or more of the following U.S. patents:

4,803,860 5,170,431 5,265,452 5,271,253 5,410,301 5,451,934 5,488,358 5,488,660

5,493,279 5,511,401 5,590,917 5,592,838 5,709,114 5,774,058 5,774,059 5,870,914

5,873,276 5,881,589 5,893,283 5,896,026 D366,822 D388,308 D388,309

Kaba Mas Corporation

749 W. Short Street, Lexington, KY 40508 USA

Phone: (859) 253-4744 FAX: (859) 255-2655

Technical Support: (800) 950-4744

www.kaba-mas.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kaba Türschloss Handbücher

Kaba

Kaba Simplex 1000 Series Installationsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba PowerLever 15 Series Bedienungsanleitung

Kaba

Kaba SIMPLEX 3000 NARROW STILE Bedienungsanleitung

Kaba

Kaba ILCO Generation E-760 Series Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5200 Bedienungsanleitung

Kaba

Kaba Digital Cylinder Bedienungsanleitung

Kaba

Kaba 7002 Series Bedienungsanleitung

Kaba

Kaba Peaks Preferred Bedienungsanleitung

Kaba

Kaba E-PLEX 5X51 Bedienungsanleitung

Kaba

Kaba E-PLEX 50XX SERIES Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Kaba

Kaba SIMPLEX 900 Series Bedienungsanleitung

Kaba

Kaba PowerLever 455 Series Bedienungsanleitung

Kaba

Kaba c-lever 2662-K5 Bedienungsanleitung

Kaba

Kaba Saflok RT Series Bedienungsanleitung

Kaba

Kaba E-Flash 680 Bedienungsanleitung

Kaba

Kaba E-Plex 5900 Bedienungsanleitung

Kaba

Kaba S-module Bedienungsanleitung

Kaba

Kaba 1547-K5 Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung