Kaba E-Plex 5900 Bedienungsanleitung

E-Plex®5xxx Series

Egress Monitoring Installation Addendum

Kaba’s E-Plex 5900 door lock will monitor opening and closing of

the door. This is accomplished by installing a position sensor in

the door, and installing a permanent magnet in the door frame.

These are shown in the pages that follow.

Installation:

Prepare the door following the E-Plex 5x00 cylindrical lock Installation

Instructions manual. The door surface will be prepared with a 1" diameter

recessed area approximately 1" deep, which will accommodate the sensor

leads to be mounted within the door. The center of this recessed area should

be 5 1

⁄2" directly above the center of the 2 1

⁄8" hole. A hole is required for the

spindle to pass through the door 2 7

⁄16" (2.4”) above the 2 1

⁄8" hole. Refer to

the Door and Door Frame Openings illustration below.

For wooden doors, the recessed area must be deep enough to meet the wiring

path drilled within the door. Do not drill the recessed area completely through

the door. For metal doors, only drill through the outside of the door. Do not

drill completely through.

Drill a horizontal hole for the sensor and wires through the edge of the door

to intersect with the recessed area 5 1

⁄2" above the latch. The horizontal hole

size is 3

⁄8" inch diameter and 1" deep for a tight t with the sensor. The

remainder should be a 1

⁄4" diameter wire path above or below the upper lock

mounting holes.

Caution: Make sure that the drill path does not interfere with the two upper

⁄4" lock mounting holes.

Outside lock mounting

surface of door.

6.0"

Sensor

Hole 5.5"

Recessed

Hole

5.4"

Mounting

Hole

2.4"

Spindle

Hole

Wire passage holes intersect,

avoiding two mounting holes.

Align magnet in door frame

with sensor in door.

Wood: .250" dia hole, .375" deep.

Steel: .295" dia hole for

mounting collar.

1" dia recessed

1" deep for wire junction

Pass through hole for small

spindle.

Latch

Door Frame

Ensure that no part of the

wires are pinched or shorted

during installation. Place

excess wire in the door, and

nish installing the lock ac-

cording to the instructions in

the manual adding the spindle

connecting both sides accord-

ing to the Spindle Installation

illustration at the right.

Locate the position for the

sensor magnet. Align the

magnet with the sensor now

mounted in the door edge.

In wood, drill a 1

⁄4" hole to be

3/8" deep for the magnet. In

steel, use a size M (.295") drill

and mount the magnet with

the collar provided.

Caution: The magnet is

strong. Avoid placing the

magnet near sensitive devices

such as magnetic stripe cards.

Route the wires through the door.

It is important to ensure that each

wire from the sensor is connected

to a wire extending from the lock

housing. Polarity is not required.

Insulate the junctions. Refer to the

Wire Connections at the left.

Egress Sensor

and Wire

Sensor

Wires in Lock

Outside

Lock

1. Push spindle into mating

socket of the outside hous-

ing until it ”snaps“ into place.

Rotate the spindle to have

the sharp edges horizontal.

2. Place socket

onto spindle.

The socket

has the sharp

corners

horizontal.

Kaba Access Control

2941 Indiana Avenue

Winston-Salem, NC 27105 USA

Tel: (800) 849-8324 (336) 725-1331

Fax: (800) 346-9640 (336) 725-3269

For Technical Assistance

Tel: 1-800-849-TECH (336) 725-1331

www.kabaaccess.com

PKG3235 0308

Andere Handbücher für E-Plex 5900

Dieses Handbuch passt für folgende Modelle

Andere Kaba Türschloss Handbücher

Kaba

Kaba E-Flash 680 Bedienungsanleitung

Kaba

Kaba E-Flash EF780 Bedienungsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba SIMPLEX 5000 CYLINDRICAL Bedienungsanleitung

Kaba

Kaba E-PLEX 5x70 Series Bedienungsanleitung

Kaba

Kaba S-module Bedienungsanleitung

Kaba

Kaba E-Plex 5900 Bedienungsanleitung

Kaba

Kaba PowerLever 455 Series Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba Peaks Preferred Bedienungsanleitung

Kaba

Kaba E-PLEX 50XX SERIES Bedienungsanleitung

Kaba

Kaba 5 00 Series Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba Confidant RFID Kit 2 Bedienungsanleitung

Kaba

Kaba SIMPLEX 900 Series Bedienungsanleitung

Kaba

Kaba E30 Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Installationsanleitung

Kaba

Kaba Saflok MT RFID Bedienungsanleitung

Kaba

Kaba 7002 Series Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Kaba

Kaba Digital Cylinder Bedienungsanleitung

Kaba

Kaba E-Plex 5X10 Bedienungsanleitung

Kaba

Kaba E-PLEX Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung