Kaba E-PLEX 50XX SERIES Bedienungsanleitung

OPERATIONS MANUAL

E-PLEX®50XX/30XX SERIES

TABLE OF CONTENTS

StatesoftheLock .............................................4

actoryMode ....................................................4

AccessMode .....................................................4

PushbuttonProgrammingMode ....................................5

Sequence of Operations for Start-Up Programming . . . . . . . . . . . . . . . . . .4

Default Values of the E-Plex™Lock Programmable Parameters . . . . . . . . . . . . .5

ConfiguringtheLock ...........................................5

General Procedure for Pushbutton Programming . . . . . . . . . . . . . . . . . . . . .5

ResetProcedures.................................................6

Procedure 1 - Program the Access Code Length . . . . . . . . . . . . . . . . . . . . . .7

Procedure 2 - Modify the Master User Access Code . . . . . . . . . . . . . . . . . . .8

Procedure3-SettheDate/Time ..................................8

Procedure 4 - Program the Lock ID and Unlock Time . . . . . . . . . . . . . . . . .9

Procedure 5 - Program the Duration of the . . . . . . . . . . . . . . . . . . . . . . . . . .9

Passage Mode Period

Procedure 6 - Program the Lock for Tamper . . . . . . . . . . . . . . . . . . . . . . . .10

Time Parameters

Procedure 7 - Programming the Lock for Keypad . . . . . . .11

Buzzer Volume

Users-GeneralInformation........................................11

UserLevels......................................................12

UserCodes...................................................13

User Access Codes (PINs) - Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Procedure 1 - Add / Modify a User Access Code . . . . . . . . . . . . . . . . . . . . . .13

Procedure 2 - Add / Modify a Manager Access Code . . . . . . . . . . . . . . . . .14

Procedure 3 - Add / Modify Service User Access Code . . . . . . . . . . . . . . . .15

Procedure 4 - Delete User Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Procedure 5 - Delete Manager Access Codes . . . . . . . . . . . . . . . . . . . . . . . .22

Procedure 6 - Delete Service User Access Codes . . . . . . . . . . . . . . . . . . . .22

Procedure 7 - Delete All Access Codes Except Master,16

Manager, and M-Unit

Procedure 8 - Activate User Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . .23

Procedure 9 - Activate Manager Access Code . . . . . . . . . . . . . . . . . . . . . . .23

Procedure 10 - Activate Service User Access Code . . . . . . . . . . . . . . . . . . .24

Procedure 11 - Activate All User Access Codes . . . . . . . . . . . . . . . . . . . . . . .24

Procedure 12 - Activate / De-activate Passage Mode . . . . . . . . . . . . . . . . .24

Procedure 13 - De-activate User Access Codes . . . . . . . . . . . . . . . . . . . . . .25

Procedure 14 - De-activate Manager Access Codes . . . . . . . . . . . . . . . . . . .25

Procedure 15 - De-activate Service User Access Code . . . . . . . . . . . . . . . .26

Procedure 16 - De-activate all Access Codes except20

Master, Manager, and M-Unit

Procedure 17 - Activate / De-activate Lockout Mode . . . . . . . . . . . . . . . . .26

Procedure 18 - Perform Manual Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . .27

Battery Life and Replacement . . . . . . . . . . . . . . . . . . . . . . . .27

Procedure 19 - Latch Holdback Operation . . . . . . . . . . . . . . . . . . . . . . . . . .28

(E-Plex 30xx Series Only)

Procedure 20 - Swing Bolt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

(E-Plex 30xx Series Only)

Summary of Pushbutton Programming Commands . . . . . . . . . . . . . . . . . . . . . . .31

Visual eedback Message Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

UserListTable ......................................................35

TABLE OF CONTENTS (continued)

A publication of Kaba Access Control

2941 Indiana Avenue

Winston-Salem, NC 27105

No part of this book may be reproduced or

transmitted in any form or by any means,

electronic or mechanical, including photocopying,

recording, or by any information storage and

retrieval system, without prior written permission

from the Publisher.

The information contained in this publication

is accurate to the best of Kaba Access

Control’s knowledge.

Specifications are subject to change

without notice.

Legend

• “E-Plex Lock” refers to both the E-Plex 5000 and the E-Plex 3000 locks.

• “E-Plex 5000” refers to the E-Plex 5000 series locks only.

• “E-Plex 3000” refers to the E-Plex 3000 series locks only.

States of the Lock

Factory Mode

The factory mode is one of three primary states of the E-Plex Lock. The main

characteristics of this state are:

• The E-Plex Lock opens only when the 8-digit master

combination (1-2-3-4-5-6-7-8) is keyed in.

• The visual indication for ‘access granted’ is green LED flashing once.

A high-pitched tone is also generated while the green LED is on.

• The Master User must change the combination to be able to exit the

factory mode, and switch to the access mode.

Access Mode

This mode refers to a lock that is operational for user access, and not in facto-

ry or Programming Mode.

Pushbutton Programming Mode

The E-Plex lock enters the Pushbutton Programming Mode when the user

enters the master combination or one of the manager combinations, preceded

and followed by the character ‘#’ (ex: #12345678#). Once the E-Plex Lock is in

the Pushbutton Programming Mode, the Master/Manager can enter one or more

command sequences. Each command sequence ends with a ‘#’ character that

acts like an < enter > character. At the very end of all sequences of program-

ming commands, enter one more # to remove the lock from the Pushbutton

Programming Mode to return to normal access mode.

Sequence of Operations for Start-Up Programming

What is the recommended sequence of operations?

With the E-Plex Lock in the factory mode.

• Program the Access Code Length (default length is four digits).

The access

code field length can only be changed when the lock is not activated

(when still in the factory mode).

• Change factory Master to your own Master Code (always eight digits) to

place lock in access mode.

Put lock in Pushbutton Programming Mode.

• Set the Date / Time

• Program the Lock ID and Unlock time

•

Program the Lock for the Duration of Passage Mode (if desired)

• Program the Lock for Tamper Time Settings

• Program the Lock for Buzzer Volume

• Add Access Codes as desired

Default values of the E-Plex®Lock programmable parameters

Parameters Factory Default Values

Date (MM/DD/YY) 01/01/00

Time (HH:MM) 00:00

Lock state Unprogrammed

Lock ID 0000

Passage mode open time limit 9 hours

Passage mode Disabled

Lockout mode Disabled

Unlock time 2 seconds

Buzzer volume control Low

Tamper shutdown time 30 seconds

Tamper attempt count 4 attempts

Access code length 4 digits

Latch Holdback Mode Disabled (E-30xx only)

Swingbolt Privilege Disabled (E-30xx only)

Privacy Privilege Disabled (E-50xx only)

Master combination 12345678 (8 digits)

Access code None

Code status Activated

M-Unit user’s combination None

M-Unit user’s status Disabled

Configuring the Lock

General Procedure for Pushbutton Programming

1. The pages that follow provide step-by-step instructions for programming

the E-Plex Lock.

2. The general procedure for all programming functions is as follows:

a. Put the lock in Programming Mode by pressing # Master Code #

b. Use the Summary of Commands Table in the appendix section of this

guide to enter the three digit command sequence (Command Type +

unction Code), followed by #.

c. Enter the appropriate numbers as required.

d. Press # to end Programming Mode.

e. Once the lock is in programming mode, multiple command sequences

can be entered without having to repeat the #mastercode#.

However, if there is no activity for 15 seconds at the keypad, the lock

will automatically exit from programming mode.

For example

• If the Master or Manager enters his code of 87654321, the door will

open.

• If he enters #87654321#, the lock will enter into the Programming

Mode and wait for the next part of the command.

• If he enters the # sign twice at the end of the code, for example

#87654321##, the lock will go out of Programming Mode and

return to its normal mode.

Note: The # pound sign acts like the Enter key on a keyboard in your

communications with the lock. The # tells the lock that one part of the

entry is finished. The # serves another purpose - to distinguish a program-

ming type command from a simple Access Code to open the door. A Master

or Manager User can use the same number to open the door or to put the

lock in Programming Mode, the only difference being that he uses the #

or increased security, it is recommended that the master user code not

be used for everyday access. This can be accomplished by creating an

access user code for the master user.

Reset Procedures

There are three different “Reset” levels available in the E-Plex Lock.

Code 099# will reset the lock to the factory default settings except for the

access code length (Master, Manager Access User codes and Time / Date

are retained if already programmed)

Code 299# will delete all access and service user codes (Master, Manager

and M-Unit * users are retained)

Hard Reset will return the lock to factory mode including deleting all codes,

putting the lock back to factory default values (4 digit access code length)

and making the master code 1-2-3-4-5-6-7-8. A hard reset is performed as fol-

lows.

Insert key, turn and hold in open position (Latch retracted).

Within 5 seconds, press # and then release latch

While red /green light flashes, press 1-2-3-4-5-6-7-8-# on keypad

The lock will reset. A green light with corresponding high pitch tone indicates

reset is complete and successful.

Lock is now reset to the factory mode and the Master Code is now

1-2-3-4-5-6-7-8.

*M-Unit is only applicable when using optional E-Plex software.

PROCEDURE 1 - PROGRAM THE ACCESS CODE

LENGTH

Setting the length of Access Codes must be the first lock programmable func-

tion you perform, because all your other access codes must have the same

length. If a user enters a code of a different length, the lock will not accept it.

Longer length Access Codes permit a greater number of code possibilities, and

thus higher security. The master code must always be 8 digits. This length can

not be changed.

Required User Level: Master

1. To configure the E-Plex Lock programmable pushbutton lock, it must first

be placed in Programming Mode.

mportant: This is the only programmable function that can be done

during the factory mode using the factory master code. Except for

changing from the factory code to a new master code.

2. Enter the E-Plex Lock factory Master (Programming) Code

(#12345678#). The lock responds with a flashing green light.

If 1-2-3-4-5-6-7-8 does not seem to work, please follow the steps

to perform a hard reset by following the procedure in on page 6.

3. Enter the code 009 #LL #, where LL represents the length (number of

digits in a code). The range is from 04 to 08 digits. You can leave the

factory default Access Code length (4 digits) if you wish by not

changing the length.

4. Example of Complete Entry: 009#05# to change the code length to 5

digits.

5. Key in another #to indicate the end of programming.

6. rom now on, all the Access Codes you create must be the length

specified in this step.

PROCEDURE 2 - MOD FY THE MASTER USER ACCESS

CODE

Required User Level: Master

1. To change the factory code or current Master Code, follow the next three

steps:

2. Put lock into Pushbutton Programming Mode.

3. Use the command, 000, for Master, then the new Master Code number.

4. You must use 8 digits between 00000000 and 99999999 as follows:

000#MMMMMMMM#, we’ll use 000#87654321# as an example.

5. Enter the Master Code again 87654321# for confirmation.

6. Example of Complete Entry: 000#87654321#87654321#.

7. Key in another #to indicate the end of programming.

8. After that, you will always use your own Master Code. Please write the code

down and keep in a safe place. The factory code is no longer valid.

PROCEDURE 3 - SET THE DATE / T ME

Note: Not required if software is not used

You must enter the current date and time in each lock to enable accurate

programming and auditing. Always enter Standard Time; the software package

will make the adjustment for Daylight Savings Time. These must be regularly

updated according to your maintenance schedule. Enter 001 for date settings

and 002 for time settings. Date / time settings are kept after a battery change

unless you remove the batteries for more than two minutes. In this case, the

time is reset to 00:00:00 and the date to 01/01/00.

Required User Level: Master

1. Put lock into pushbutton programming mode.

2. Enter the date as follows: 001#MMDDYY# (Month, Day, Year, where MM

= 01 to 12; DD = 01 to 31; YY = 00 to 99. or example, Nov. 22, 2007

would be entered as 112207).

3. Enter the date again to confirm MMDDYY#. Example of Complete Entry:

001#112207#112207#.

4. or the time, enter as follows: 002#HHMM#, where HH = 00 to 23

hours; MM = 00 to 59 minutes. Use military time - for example eight-

thirty in the morning would be 0830, while in the evening it would be

2030).

5. Enter the code again HHMM#, for example 0830.

6. Example of Complete Entry: 002#0830#0830#.

7. Enter another #to indicate the end of programming.

8. The current date and time are now programmed into the lock.

PROCEDURE 4 - PROGRAM THE LOCK D AND

UNLOCK T ME

Assign an ID number to each lock for configuration and auditing purposes. This is

an internal number (default 0000), and is the same as the door number. Unlock

time is the length of time the door will remain unlocked when a correct code is

entered before automatically re-locking itself.

Required User Level: Lock D: Master, Unlock Time: Master, Manager

1. Put the lock into Pushbutton Programming Mode.

2. To set up the Lock ID, enter command 003#.

3. Enter NNNN (where NNNN is the lock ID - a number from 0000 to

9999). or example, 1234.

4. Example of Complete Entry: 003#1234#.

5. The lock ID is now in its memory.

6. Enter another #to indicate the end of programming, or remain in

programming mode to continue.

7. To establish Unlock Time, enter the following code: 004#TT#,where TT

is the time in seconds, (TT=02 to 20 seconds, for example 10 seconds).

8. Example of Complete Entry: 004#10#.

9. Enter another #to indicate the end of programming.

10. You have now programmed the lock ID 1234 and, for example, an Unlock

Time of 10 seconds for the door.

PROCEDURE 5 - PROGRAM THE DURAT ON OF THE

PASSAGE MODE PER OD

You might want to program locks for public areas, such as cafeterias, to have

free access (Passage Mode) during certain periods of the day, and revert to

required code access outside of these regular hours.

The length of time that the lock remains in Passage Mode is programmable.

The factory default length of time for Passage Mode is 9 hours - you may leave

the default, but by default, the lock’s passage mode is de-activated.

When the lock is activated at the lock keypad to go into Passage Mode, it will

automatically relock after the designated duration.

Required User Level: Master, Manager

1. Put the lock into Pushbutton Programming Mode.

2. Enter command code 005#.

3. Then TT#, where TT= 01 to 24 hours.

4. A TT entry of 00 means there is no time limit - the door remains

unlocked (permanently).

5. Enter 005 #TT#; for example, 005#06# for six hours.

6. Example of Complete Entry: 005#06#.

7. Enter another #to indicate the end of programming.

8. In this example, the lock will remain unlocked for six hours, starting from

the time you activate it in Passage Mode.

9. You have now configured the duration of the Passage Mode period for

that lock. This does NOT initiate Passage Mode until you activate the

Passage Mode - See Procedure 12 on “How to activate/deactivate the

Passage Mode.”

10. The new length of time will take effect the next time you put a lock into

Passage Mode by following the correct command sequence.

PROCEDURE 6 - PROGRAM THE LOCK FOR TAMPER

T ME PARAMETERS

You can set a Tamper Time Wrong Tries parameter referring to the number

of times the wrong code can be entered before the lock goes into Tamper

Shutdown Mode.

or example, if you program the lock to accept three wrong tries, the lock will

tolerate three wrong entries, staying locked but providing visual feedback (see

visual message chart in rear section). After that, it will go into a Tamper

Shutdown Mode and remain locked until the end of the Tamper Shutdown Time

period - the length of that period is configured in Step 4 of this procedure

(below).

Required User Level: Master, Manager

1. Set the tamper time for the period of time during which the keypad will

remain inaccessible after the specified number of wrong Access Codes

are entered

2. Put the lock into Pushbutton Programming Mode.

3. Enter the code as follows - 006#TT# (TT is seconds - 00 to 90 seconds).

4. Example of Complete Entry: 006#60#. (for 60 seconds)

5. Enter the code as follows: 007 #TT# (TT is number of wrong entries -

03 to 09), let’s use 05 for example.

6. Example of Complete Entry: 007#05#.

7. Enter another #to indicate the end of programming.

8. The lock will stay locked after three wrong entries for the length of time

you select in the steps below, even if a valid code (including the

Master or a Manager Code) is entered after the three wrong codes.

Only the mechanical key override will open the lock during the

tamper shut down Period.

9. Enter another #to indicate the end of programming.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kaba Türschloss Handbücher

Kaba

Kaba Digital Cylinder Bedienungsanleitung

Kaba

Kaba E-PLEX STANDARD Series Bedienungsanleitung

Kaba

Kaba E-PLEX Bedienungsanleitung

Kaba

Kaba Combi B 30 Bedienungsanleitung

Kaba

Kaba ILCO Generation E-760 Series Bedienungsanleitung

Kaba

Kaba 7102 series Bedienungsanleitung

Kaba

Kaba Ilco 790/79 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5X10 Bedienungsanleitung

Kaba

Kaba EF 680E Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Kaba

Kaba 7002 Series Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba E-PLEX 3x65 Deadlatch/Exit Mortise Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Bedienungsanleitung

Kaba

Kaba PowerLever 1550 Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba E-PLEX 5X51 Bedienungsanleitung

Kaba

Kaba 1547-K5 Bedienungsanleitung

Kaba

Kaba E-Plex 5900 Bedienungsanleitung

Kaba

Kaba Peaks Preferred Bedienungsanleitung

Kaba

Kaba E-Plex 5200 Bedienungsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba S-module Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung